ML Accessories GDL2 User manual
- Category
- Mounting kits
- Type
- User manual
This manual is also suitable for
ML Accessories GDL2 is a dimmable IP54 rated outdoor light that is suitable for domestic areas, with decorative and ornamental use cases in mind. The fitting contains a GU10 lamp holder which is compatible with GU10 lamps with a maximum wattage of 35W (not included). The GDL2 is compatible with the GDLSPIKE2 or the GDLMK23 for mounting.
ML Accessories GDL2 is a dimmable IP54 rated outdoor light that is suitable for domestic areas, with decorative and ornamental use cases in mind. The fitting contains a GU10 lamp holder which is compatible with GU10 lamps with a maximum wattage of 35W (not included). The GDL2 is compatible with the GDLSPIKE2 or the GDLMK23 for mounting.
INSTALLATION & MAINTENANCE MANUAL
GDL2 / GDL3
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following products:
GDL2 / GDL3
GENERAL INSTRUCTIONS
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is Class I and must be earthed
• This product is IP54 rated
SAFETY
• Provide power to the required point of installation. Suitable IP rated junction boxes should be used where
required
• Remove the four baseplate hex screws and remove baseplate (see Fig. 1)
INSTALLATION
• Using the baseplate as a template, mark the location of the fixing holes and drill the holes ensuring not to
infringe with any gas/water pipes or electrical cables
• Use expansion bolts or appropriate fixings to secure the baseplate to the desired surface
(not included, see ‘Mounting’)
• Remove the four junction box screws and remove the cover (see Fig. 2)
Fig. 1
GDL2 / GDL3
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following products;
GDL2 / GDL3
SAFETY
• Installation of this luminaire should only be carried out by a qualified electrician or competent person to the
latest Building and current IEE Wiring Regulations (BS7671)
• Please isolate mains prior to installation/maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for installation
• This product is Class I and should be earthed
• This product is IP54 rated
INSTALLATION
• Provide power to the required point of installation. Suitable IP rated junction boxes should be used where
required
• Remove the four base plate hex screws and remove base plate (see Fig 1)
Fig 1
• Using the base plate as a template, mark the location of the fixing holes and drill the holes ensuring not to
infringe with any gas/water pipes or electrical cables
• Remove the four junction box screws and remove the cover (see Fig 2)
Fig 2
Remove hex screws
Remove screws
GDL2 / GDL3
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following products;
GDL2 / GDL3
SAFETY
• Installation of this luminaire should only be carried out by a qualified electrician or competent person to the
latest Building and current IEE Wiring Regulations (BS7671)
• Please isolate mains prior to installation/maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for installation
• This product is Class I and should be earthed
• This product is IP54 rated
INSTALLATION
• Provide power to the required point of installation. Suitable IP rated junction boxes should be used where
required
• Remove the four base plate hex screws and remove base plate (see Fig 1)
Fig 1
• Using the base plate as a template, mark the location of the fixing holes and drill the holes ensuring not to
infringe with any gas/water pipes or electrical cables
• Remove the four junction box screws and remove the cover (see Fig 2)
Fig 2
Remove hex screws
Remove screws
Fig. 2
• Ensuring that correct polarity is observed, terminate the mains cable in the terminal block within the
junction box (see Fig. 3)
• Ensuring that correct polarity is observed, terminate the mains cable in the terminal block within the junction box
(see Fig 3)
Fig 3
• Refit the junction box cover and fasten
• Secure the fitting back to the base plate and fasten the four hex screws (see Fig 4)
Fig 4
• Switch on and check for correct operation
MOUNTING
The GDL2 is suitable for use with the GDLSPIKE2 or the GDLMK23
The GDL3 is only suitable for use with the GDLMK23
Live (brown)
• Refit the junction box cover and fasten
• Secure the fitting back to the baseplate and fasten the four hex screws (see Fig. 4)
Fig. 3
Live (brown)
Earth (yellow/green)
Neutral (blue)
Fig. 4
• Ensuring that correct polarity is observed, terminate the mains cable in the terminal block within the junction box
(see Fig 3)
Fig 3
• Refit the junction box cover and fasten
• Secure the fitting back to the base plate and fasten the four hex screws (see Fig 4)
Fig 4
• Switch on and check for correct operation
MOUNTING
The GDL2 is suitable for use with the GDLSPIKE2 or the GDLMK23
The GDL3 is only suitable for use with the GDLMK23
Live (brown)
• Remove both hex screws using the Allen key provided to gain access to the GU10 lamp holder (see Fig. 5)
• Ensuring that correct polarity is observed, terminate the mains cable in the terminal block within the junction box
(see Fig 3)
Fig 3
• Refit the junction box cover and fasten
• Secure the fitting back to the base plate and fasten the four hex screws (see Fig 4)
Fig 4
LAMP INSTALLATION
• Remove both Allen screws using the Allen key provided to gain access to the GU10 lamp holder (see Fig 5)
Fig 5
Remove Allen screws
Fig. 5
LAMP INSTALLATION
This luminaire is intended for domestic areas, and for decorative and ornamental use only.
The GDL2 is suitable for use with the GDLSPIKE2 or the GDLMK23
The GDL3 is only suitable for use with the GDLMK23
Important: Ensure correct fixings are used to suit the installation environment and mounting surface
• Install a GU10 lamp into the fitting ensuring not to exceed the maximum 35W rating (lamp not included)
• Switch on and check for correct operation
MOUNTING
WARNING
Remove hex screws
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do
not use aggressive cleaning products or solvents which may damage the product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product is not suitable for installation in or near a coastal or marine environment.
A light film of acid-free oil is recommended after installation and maintained periodically (2-3 times a year) to
aid corrosion prevention.
This product is dimmable dependent on lamp type.
This product should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist.
GENERAL
This product has a warranty of 2 years from date of purchase. Failure to install this product in accordance
with the current edition of the IEE Wiring Regulations, improper use, or removal of the batch codes will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the
place of purchase for a free of charge replacement. ML Accessories does not accept responsibility for
any installation costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.
WARRANTY
DCJUL21_V3
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
02
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
-
1
-
2
-
3
-
4
-
5
-
6
-
7
ML Accessories GDL2 User manual
- Category
- Mounting kits
- Type
- User manual
- This manual is also suitable for
ML Accessories GDL2 is a dimmable IP54 rated outdoor light that is suitable for domestic areas, with decorative and ornamental use cases in mind. The fitting contains a GU10 lamp holder which is compatible with GU10 lamps with a maximum wattage of 35W (not included). The GDL2 is compatible with the GDLSPIKE2 or the GDLMK23 for mounting.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ML Accessories NETTS1WH User manual
-
-
-
-
-
-
-
-
-
Other documents
-
Knightsbridge CSPT1BC User manual
-
-
-
Knightsbridge OL01B User manual
-
Knightsbridge TORI5F4K Installation guide
-
SG O243S Owner's manual
-
Eglo O87SS Owner's manual
-
-
Knightsbridge ODA1FSB User manual
-
