Clarke Tiger Series Operation & Maintenance Instructions Manual

Brand: Clarke

Model: Tiger Series

Type: Operation & Maintenance Instructions Manual

This manual is also suitable for

OPERATION & MAINTENANCE

INSTRUCTIONS

MODEL No: Tiger 1501 - 1801

TIGER ENGINE DRIVEN WASHERS

-2-

Thank you for purchasing this CLARKE Power Washer.

Before attempting to use the machine, please read this manual, together with the engine

manual provided thoroughly and follow the instructions carefully. In doing so you will ensure

the safety of yourself and that of others around you, and you can look forward to the

washer giving you long and satisfactory service.

Guarantee

This product is guaranteed against faulty manufacture for a period of 12 months from the

date of purchase. Please keep your receipt which will be required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in

any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to

us without prior permission.

This guarantee does not effect your statutory rights.

Specifications

Tiger 1501 Tiger1801

Part No ....................................... 7320051 7320053

Maximum Pressure .................... 100 bar 120 bar

Maximum Flow .......................... 9 L/min 11 L/min

Engine Type ............................... Honda GC135 Honda GC160

Engine Rating ............................ 4.0Hp 5.0Hp

Mounting .................................... Frame/Carry Handle Trolley

Dimensions (LWH) ...................... 535x370x440mm 600x400x800

Weight ........................................ 21Kg 32Kg

Please note that the details and specifications contained herein, are correct at the time of going to print. However,

CLARKE International reserve the right to change specifications at any time without prior notice.

When disposing of this product, do not dispose of with general waste. It must be disposed

of according to the laws governing Waste Electrical and Electronic equipment, at a

recognised disposal facility.

-3-

Safety Precautions

WARNING:

As with all machinery, there are certain hazards involved with their operation

and use. Exercising respect and caution will considerably lessen the risk of

personal injury. However, if normal safety precautions are overlooked or

ignored, personal injury to the operator or damage to property, may result.

WARNING : Water at high pressure can be dangerous if subject to misuse. NEVER allow

anyone to operate this equipment unless they are thoroughly reliable and familiar

with the safety precations.

Before operating the power washer learn the machines’ applications, limitations and the

specific potential hazards peculiar to it. Read and become familiar with the entire operating

manual.

1. NEVER aim water jet at people or animals.

2. NEVER allow children to use or play with the machine.

3. NEVER hold your finger over the high pressure nozzle.

4. NEVER aim jet at the machine itself, or any electrcal equipment, unless adequately

protected.

5. NEVER train the jet at windows, particularly greenhouses etc, also be aware that the

high pressure jet can damage painted surfaces.

6. NEVER operate the machine whilst standing on ladders. ALWAYS use a platform

tower or scaffolding.

7. NEVER change accessories etc with pressure in the high pressure hose. To release

the pressure, switch the machine OFF and operate the trigger.

8. NEVER use solvents, e.g. paint thinners, petrol, oil etc in the detergent reservoir.

9. ALWAYS check for damage. Before using the machine, any damaged part, should

be checked to ensure that it will operate properly, and perform its intended

function. Check for alignment of moving parts, breakage of parts, mountings, and

any other condition that may affect the machines’ operation. Any damage should

be properly repaired or the part replaced. If in doubt, DO NOT use the machine.

Consult your local dealer.

10. ALWAYS disconnect the machine from the power supply before servicing and when

changing accessories.

12. ALWAYS wear safety goggles, manufactured to the latest European Safety Standards.

Everyday eyeglasses do not have impact resistant lenses, they are NOT safety glasses.

13. ALWAYS ensure that adequate lighting is available.

14. ALWAYS keep children away. All visitors should be kept a safe distance from the

work area, especially whilst operating the machine.

15. ALWAYS maintain machine in top condition. Keep machines clean for the best and

safest performance. Follow maintenance instructions.

16. ALWAYS ensure the ON/OFF switch is OFF before plugging in to mains. Avoid accidental

starting.

17. ALWAYS ensure the machine is completely drained before storing for lengthy periods.

18. USE ONLY chemical cleaning agents (detergents) approved for use in power washers.

-4-

Features

These fully portable machines incorporate a variable pressure control, together with a

fan or jet spray, and may be used with or without detergent. Although these machines

were designed to operate using a mains water supply, they will also work satisfactorily

with a supply which is under positive pressure, i.e. from an elevated water tank etc.

NOTE: when using water from the mains supply, you must always comply with local

authority by-laws.

High Pressure

Hose connection

Detergent

Hose

Connection

Water Supply IN

Filter (Detergent)

Pressure

Regulator

Fig. 1

Assembly

and Preparation

for use

1. Assemble the lance

by screwing section

‘B’ into section ‘A’ (Fig. 2).

2. Remove all travel

blanking plugs.

3. Connect one end of

the high pressure hose

to the lance.

4. Connect the other end to the

High pressure connection on

the pump (Fig. !).

Note: Ensure the sealing rings are in place before tightening (DO NOT Overtighten).

5. Connect one end of the hose pipe (not supplied) to the water supply.

6. Connect the other end to the Water Supply IN connection on the pump.

Note: To connect the hose to the pump, it is recommended to use a snap connector

available from any DIY, Hardware and Gardening supply store.

A good quality hose of at least ½” dia,should be used, also available from Hardware and

Gardening supply stores.

All connections should be tight to avoid leaks.

Fig. 2

Fig

‘A’

‘B’

High Pressure

Hose

Connection

Pump Oil Sight Glass

-5-

8. When required, the detergent pick up hose should be connected to the spigot

adjacent to the high pressure hose connector.

9. Check the engine fuel and oil lvels,(Refer to oil levels in the engine handbook,

top up if necessary.

Operation

1. Turn the water supply ON fully at the mains.

2. Release the safety catch on the lance trigger (OFF), squeeze

the trigger to expel any air in the system.

Water will trickle from the end of the lance

when the air is expelled.

3. Start the engine, REFER TO

THE ENGINE HANDBOOK.

Move the speed control lever

to MAX.

NOTE: If you experience starting

difficulties, squeeze the trigger, and

keep it squeezed, whilst trying to start the engine,

this will relieve pressure in the system, and

provide for easier starting.

4. Pull the nozzle towards you to set the

lance at high pressure, and away from

you to set it at low pressure. (see Fig. 4).

NOTE: When sprying detergents etc, always use the low pressure setting.

5. By twisting the nozzle as shown in Fig. 5, you can select either a fan spray or a

narrow jet.

Fig. 4

Check there are no leaks in the system/connections. Any leaks should be rectified before

continuing.

Fig. 5

Trigger Lock

OFF

Trigger

High Pressure

Hose

Connection

Fig. 3

-6-

Chemical Cleaning Agents

To improve cleaning qualities, it is possible to inject chemical cleaning agents

(detergents) into the low pressure spray, particularly useful for washing cars, greasy

engines, oil spots on concrete etc.

To inject detergents, insert the clear plastic hose with filter attachment into the detergent

container, ensuring it is completely submerged.

Maintenance

If detergents have been used, it is important to flush the system thoroughly with clean

water.

If there is a danger of freezing, anti-freeze should be mixed with the flush water, after

flushing, the system must be drained as far as possible.

After the final flush - stop the engine. Do not allow it to idle for longer than 15seconds.

The pump oil level should be checked regularly, by viewing the oil level in the sight glass

(see Fig. 1), the correct level is indicated when the oil is in line with the red dot.

If the level falls below the red dot, top up with Clarke pump oil (sae 30 - part No 3055801).

To top up the oil, proceed as follows:

Ensure the engine is not running.

Loosen and remove the two cap head screws on top of the pump cover. Remove cover

STORAGE

Store in an upright position, completely drained of water,

ENGINE

Refer to the engine handbook, and service accordingly.

NOTE: Use ONLY detergents designed for use with power washers. We recommend the use

of CLARKE Traffic Film Remover, which is a powerful low foaming agent for car cleaning,

patio cleaning etc, or CLARKE Wash and Wax, available from your nearest CLARKE dealer.

When detergent injection is required, slide the lance nozzle away from you top the low

pressure setting, the detergent will be automatically drawn into the water supply. Spray

the detergent onto the vehicle, patio etc, and allow it to work itself into the grime.

To rinse clean ,set the lance to its high pressure setting, and blast off the dirt. Take care

when using high pressure on car bodywork etc.

After cleaning, suspend the detergent hose in a container of clean water, set the lance

to low pressure, and thoroughly flush out the machine.

-7-

Parts List

1 Engine 1501 Honda 7999010 7999020 1

2 Pump 21652 21653 1

3 Frame 1321910 8820027 1

3a Wheel 1801 (not shown) N/A 2100303 2

3b Clip RDF 25 1801 (not shown) N/A 2100304 2

4 Cover 1982311 1982311 1

9 Drive Key 881090 881090 1

13 Foot 1321920 N/A 4

13a Nut 380242 N/A 4

14 Hose Connection 1270940 1270940 1

15 Detergent Hose 1262790 1262790 1

16 Detergent Filter 1341030 1341030 1

16a Detergent Hose assembly 1269115 1269115 1

17 Data Plate 5885??? 5885??? 1

18 Pressure Hose 7310170 7310170 1

19 Gun 7310771 7310771 1

20 Lance 7310774 N/A 1

21 Lance (Not Shown) N/A 7310775 1

22 Bracket 1982300 1982300 1

No Description Part Number

Tiger1501 Tiger1801 Qty

PARTS & SERVICE TEL: 020 8988 7400

or e-mail as follows:

PARTS: [email protected]

SERVICE: [email protected]

-8-

Parts Diagram

Clarke Tiger Series Operation & Maintenance Instructions Manual

Brand: Clarke

Model: Tiger Series

Type: Operation & Maintenance Instructions Manual

This manual is also suitable for

Download PDF

report

Clarke Tiger Series Operation & Maintenance Instructions Manual

This manual is also suitable for

Clarke Tiger Series Operation & Maintenance Instructions Manual

Related papers

Other documents