Milan Technology MIL-SM8002TG User manual

Category
Network switches
Type
User manual
Rev.A1
18-SEPT-2006
MIL-SM8002TG
9 Port 10/100/1000BASE-T
Two Combo 1000BASE-X SFP
Ports
Advanced Managed Switch
User Guide
Regulatory Approval
- FCC Class A
- UL 1950
- CSA C22.2 No. 950
- EN60950
- CE
- EN55022 Class A
- EN55024
Canadian EMI Notice
This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada.
European Notice
Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by
the Commission of the European Community Compliance with these directives imply conformity to the following European Norms:
EN55022 (CISPR 22) - Radio Frequency Interference
EN61000-X - Electromagnetic Immunity
EN60950 (IEC950) - Product Safety
Five-Year Limited Warranty
Transition Networks warrants to the original consumer or purchaser that each of it's products,
and all components thereof, will be free from defects in material and/or workmanship for a
period of five years from the original factory shipment date. Any warranty hereunder is
extended to the original consumer or purchaser and is not assignable.
Transition Networks makes no express or implied warranties including, but not limited to, any
implied warranty of merchantability or fitness for a particular purpose, except as expressly set
forth in this warranty. In no event shall Transition Networks be liable for incidental or
consequential damages, costs, or expenses arising out of or in connection with the
performance of the product delivered hereunder. Transition Networks will in no case cover
damages arising out of the product being used in a negligent fashion or manner.
Trademarks
The MiLAN logo Transition Networks trademarks are registered trademarks of Transition Networks in the
United States and/or other countries.
To Contact Transition Networks
For prompt response when calling for service information, have the following information ready:
- Product serial number and revision
- Date of purchase
- Vendor or place of purchase
You can reach Transition Networks technical support at:
E-mail: support@transition.com
Telephone: +1.800.260.1312 x 200 Fax: +1.952.941.2322
Transition Networks
6475 City West Parkway
Eden Prairie, MN 55344
United States of America
Telephone: +1.800.526.9267
Fax: : +1.952.941.2322
http://www.milan.com
info@ Transition.com
© Copyright 2006 Transition Networks
Content
Introduction............................................................................................................. 1
Features ............................................................................................................................1
Software Features .............................................................................................................2
Package Contents .............................................................................................................5
Hardware Description............................................................................................. 6
Physical Dimension ...........................................................................................................6
Front Panel ........................................................................................................................6
LED Indicators ...................................................................................................................7
Rear Panel.........................................................................................................................8
Desktop Installation ...........................................................................................................8
Power On...........................................................................................................................8
Network Application ............................................................................................... 9
Desktop Application...........................................................................................................9
Indoor & Protected Outdoor Application ............................................................................9
Console Management............................................................................................. 9
Console Management........................................................................................... 10
Connecting to the Console Port.......................................................................................10
Login in the Console Interface .........................................................................................10
CLI Management .............................................................................................................13
Commands Level......................................................................................................13
Commands Set List........................................................................................................14
System Commands Set ...........................................................................................14
Port Commands Set................................................................................................16
Trunk Commands Set..............................................................................................20
VLAN Commands Set..............................................................................................21
Spanning Tree Commands Set ..................................................................................23
QOS Commands Set...............................................................................................26
IGMP Commands Set..............................................................................................28
Mac / Filter Table Commands Set...............................................................................29
SNMP Commands Set.............................................................................................30
Port Mirroring Commands Set....................................................................................31
Stacking Commands Set ..........................................................................................32
802.1x Commands Set ............................................................................................33
TFTP Commands Set..............................................................................................35
Main Menu.......................................................................................................................36
System Configuration ......................................................................................................37
System Information...................................................................................................38
IP Configuration........................................................................................................39
DHCP Configuration .................................................................................................41
DHCP Server Configuration ..............................................................................41
DHCP Client Entries..........................................................................................43
Port and IP Bindings..........................................................................................44
Firmware Update......................................................................................................45
System Event Log ....................................................................................................46
System Log Configuration .................................................................................47
Event Configuration...........................................................................................48
Email Alert Configuration..........................................................................................49
SMTP Configuration ..........................................................................................50
Recipient’s email Configuration .........................................................................51
Security Manager ..............................................................................................52
Port Configuration............................................................................................................54
Port Counters ...........................................................................................................54
Port Control Configuration ........................................................................................55
Trunk Configuration ..................................................................................................56
Aggregator setting .............................................................................................57
Aggregator Information......................................................................................58
State Activity......................................................................................................59
Port Mirroring Configuration .....................................................................................60
Rate Limiting....................................................................................................................61
Protocol Configuration .....................................................................................................63
VLAN Configuration..................................................................................................63
Port Base VLAN Configure................................................................................64
Group Add..................................................................................................65
Group Remove...........................................................................................66
Group List...................................................................................................67
802.1Q VLAN Configure....................................................................................68
GVRP Setting.............................................................................................69
Configure VLAN by Port .............................................................................70
VLAN List ...................................................................................................71
Rapid Spanning Tree................................................................................................72
RSTP System Configuration..............................................................................73
RSTP Per Port Configuration ............................................................................74
SNMP Configuration.................................................................................................76
System Options .................................................................................................77
Community Strings ............................................................................................78
Trap Managers ..................................................................................................79
SNMP V 3 Configuration ...................................................................................80
Context Table.............................................................................................81
User Table..................................................................................................82
Group Table ...............................................................................................83
Access Table..............................................................................................84
MIBview Table............................................................................................87
QoS Configuration ....................................................................................................90
QoS Policy and Priority Type.............................................................................91
Default Port Priority ...........................................................................................92
COS Configuration ............................................................................................93
TOS Configuration.............................................................................................94
SNTP Configuration..................................................................................................95
IGMP Configuration ..................................................................................................98
IGMP Configuration...........................................................................................99
IGMP Status....................................................................................................100
Super ring ......................................................................................................................100
Security Configuration ...................................................................................................102
Security Configuration ...................................................................................................103
802.1X/ Radius Configuration.................................................................................103
System Configuration ......................................................................................104
802.1x Per Port Configuration .........................................................................105
Misc Configuration...........................................................................................106
Port Security...........................................................................................................107
Static MAC Address ........................................................................................108
Filtering MAC Address.....................................................................................109
All MAC Address .............................................................................................110
Load Factory Default Setting .........................................................................................111
Save All Configuration ...................................................................................................112
Reboot System ..............................................................................................................113
Web-Based Management ................................................................................... 115
Preparing for Web Management....................................................................................115
System Login.................................................................................................................115
System Information........................................................................................................116
IP Address .....................................................................................................................117
DHCP Configuration ......................................................................................................118
DHCP Server Configuration ...................................................................................119
DHCP Client Entries ...............................................................................................120
Port and IP Bindings...............................................................................................120
Update Firmware ...........................................................................................................121
Restore Configuration....................................................................................................122
Backup Configuration ....................................................................................................122
System Log Configuration .............................................................................................123
Event Configuration .......................................................................................................124
SMTP Configuration ......................................................................................................126
Security Manager...........................................................................................................127
Port Statistics.................................................................................................................128
Port Control ...................................................................................................................128
View the Single Port Information ............................................................................129
Port Trunk......................................................................................................................130
Aggregator setting ..................................................................................................130
Aggregator Information...........................................................................................131
State Activity...........................................................................................................132
Port Mirroring.................................................................................................................133
Rate Limiting..................................................................................................................134
VLAN configuration........................................................................................................135
Port-based VLAN....................................................................................................136
802.1Q VLAN .........................................................................................................138
802.1Q Configuration ......................................................................................140
Group Configuration ........................................................................................140
Rapid Spanning Tree.....................................................................................................142
RSTP System Configuration...................................................................................142
RSTP Per Port Configuration..................................................................................144
SNMP Configuration......................................................................................................145
System Configuration .............................................................................................145
Trap Managers .......................................................................................................147
SNMPV3 Configuration ..........................................................................................148
Context Table...........................................................................................148
User Table................................................................................................148
Group Table .............................................................................................150
Access Table............................................................................................151
MIBview Table..........................................................................................151
QoS Configuration .........................................................................................................152
QoS Policy and Priority Type..................................................................................152
Port Base Priority....................................................................................................153
COS Configuration .................................................................................................154
TOS Configuration..................................................................................................154
SNTP Configuration.......................................................................................................154
IGMP Configuration .......................................................................................................157
Super ring ......................................................................................................................159
Security Configuration ...................................................................................................161
802.1X Configuration..............................................................................................161
System Configuration ......................................................................................161
802.1x Per Port Configuration .........................................................................162
Misc Configuration...........................................................................................163
Port Security...........................................................................................................164
Static MAC Address ........................................................................................164
Filtering MAC Address.....................................................................................166
All MAC Address .............................................................................................167
Factory Default ..............................................................................................................167
Save Configuration ........................................................................................................168
System Reboot ..............................................................................................................168
Troubleshooting ................................................................................................. 169
Incorrect connections.....................................................................................................169
Faulty or loose cables .....................................................................................169
Non-standard cables .......................................................................................169
Improper Network Topologies .........................................................................170
Diagnosing LED Indicators ............................................................................................170
Technical Specifications.................................................................................... 171
1
Introduction
The product is a multi-port switch that can be used to build high-performance switched
indoor or protected outdoor networks. It provides wire-speed, Gigabit Ethernet switching
function that allows high-performance, low-cost connection. The Switch features a
store-and-forward switching and it can automatically learn and store source address in an
8K-entry MAC address table.
Features
Nine ports of 10/100/1000BASE-T
Two SFP 1000BASE-X transceiver slots
IEEE802.3 10BASE-T, 802.3u 100BASE-TX, 802.3z Gigabit fiber and IEEE 802.3ab
1000Base-T
IGMP snooping and Query mode support for Multi-Media application
18Gbps switch fabric
26.7Mpps throughput
802.1p CoS, per port 4 queues
IEEE802.3x Flow control
Flow control for full duplex
Back pressure for half duplex
Port Based VLAN /802 .1Q VLAN
IEEE802.3ad Port trunk with LACP
Spanning tree protocol
Rapid STP
QoS:
Port based / Tag based
IPv4 ToS/ Ipv4, IPv6 DiffServe
Port mirroring and bandwidth control
IEEE 802.1x user authentication
GVRP and MVR
2
Broadcast storm filter
DHCP Client, Relay, Server
Per port band width control
SNTP and SMTP support
Management IP address security
MAC address security
System log
SNMP Trap support
Configuration up-load and down-load
TFTP firmware update
Web/SNMP/Telnet/CLI /RMON management
Software Features
Management
SNMP v1, SNMP v2c, SNMP v3, Telnet,
Console (Command line interface), Web
management and RMON 1(1,2, 3,9)
RFC standard
RFC2233 MIBII, RFC 1157 SNMP MIB, RFC
1493 Bridge MIB, RFC 2674 VLAN MIB, RFC
2665 Ethernet like MIB, RFC1215 Trap MIB,
RFC 2819 RMON MIB, Private MIB, RFC2030
SNTP, RFC 2821 SMTP, RFC 1757 RMON1
MIB
SNMP Trap
Cold start, warm start, link down, link up,
authorization fail, Trap station up to 3.
Software Upgrade TFTP firmware upgradeable.
3
Port Trunk
Support IEEE802.3ad with LACP function. Up
to 3 trunk groups and maximum group
member up to 8 ports.
Spanning Tree
IEEE802.1d Spanning tree
IEEE802.1w Rapid spanning tree
VLAN
Port based VLAN
Double Tag VLAN for management
IEEE802.1Q Tag VLAN.
The static VLAN groups up to 256 and
dynamic VLAN groups up to 2048, the VLAN
ID can be assigned from 1 to 4094.
GVRP function supports 256 groups.
Class of Service
Per port supports 4 queues.
Wnine round ratio (WRR): High: Mid-High:
Mid-Low: Low (8:4:2:1)
Quality of service
Port based, Tag based, IPv4 Type of service,
IPv4/IPv6 Different service.
IGMP
IGMP v1 and v2 compliance and also supports
256 IGMP groups and support query mode.
Port Security
It supports ingress and egress MAC address
filter and static source MAC address lock.
Port Mirror
Global system supports 3 mirroring types:
“RX, TX and Both packet”. The maximum of
port mirror entries is up to 8.
Bandwidth Control
Ingress rate limiting packet type: all of frames,
broadcast, multicast, unknown unicast and
4
broadcast packet.
Egress rate shaping supports all of packet.
Rate limiting levels: 64kbps to 64Mbits or up to
256Mbits for Gigabit port.
User
Authentication
Support IEEE802.1x User-Authentication and
can report to RADIUS server.
Reject
Accept
Authorize
Disable
System login
security
Provide IP management security function and
provide 4 accounts.
DHCP
DHCP Client, DHCP relay and DHCP Server.
DHCP server provides port based and system
based IP pool.
Packet filter
Broadcast storm packet filter by 5%, 10%,
15% and 25%.
System log
Provide 1000 log entries and support remote
storage function.
DNS Support DNS client function.
NTP
Support RFC2030 Simple Network Time
Protocol and up to 5 NTP server.
SMTP Up to 6 mail accounts.
5
Configuration
upload and
download
Support binary format configuration file for
system quick configuration.
Package Contents
Unpack the contents of the switch and verify them against the checklist below.
Managed Switch unit
Power Cord
Four Rubber Feet
RS-232 cable
User Manual
If any item is missing or damaged, please contact your local dealer for service.
6
Hardware Description
Physical Dimension
The physical dimensions of the switch is 217mm(W) x 140mm(D) x 43mm(H)
Front Panel
The Front Panel of the switch consist of 9x auto-sensing 10/100/1000Mbps Ethernet
RJ-45 ports (automatic MDI/MDIX), 2 SFP copper combo ports, and the LED indicators
are also located on the frond panel of the switch.
Front Panel of the switch
RJ-45 Ports (Auto MDI/MDIX): Nine 10/100/1000 auto- sensing for 10Base-T or
100Base-TX or 1000Base-T connections.
In general, MDI means connecting to another Hub or Switch while MDIX means
connecting to a workstation or PC. Therefore, Auto MDI/MDIX means that you can
connect to another Switch or workstation without changing non-crossover or
crossover cabling.
2 SFP/Giga copper combo port: 2 auto detect Giga port—UTP or fiber. Giga fiber is
the SFP module that is optional.
7
LED Indicators
The following table provides descriptions of the LED statuses and meaning. They provide
a real-time indication of systematic operation status.
LED Status Description
Power
Green Power On
Yellow
The port is operating at the speed of
1000Mbps.
Orange
The port is operating at the speed of
100Mbps.
1000M
Off
The port is operating at the speed of
10Mbps or no device attached
Green
The port is successfully connecting
with the device.
Blinks
The port is receiving or transmitting
data.
LNK / ACT
Off No device attached.
Green
The port is successfully connecting
with the device.
Blinks
The port is receiving or transmitting
data.
LNK / ACT
(SFP)
Off No device attached.
8
Rear Panel
The 3-pronged power plug are located at the Rear Panel of the switch as shown in figure.
The Switches will work with AC in the range 90-240V AC, 50-60Hz.
Rear Panel of the switch
Desktop Installation
Set the switch on a sufficiently large flat space with a power outlet nearby. The surface
where you put your Switch should be clean, smooth, level, and sturdy. Make sure there is
enough clearance around the Switch to allow attachment of cables, power cord and air
circulation.
Attaching Rubber Feet
1. Make sure mounting surface on the bottom of the Switch is grease and dust free.
2. Remove adhesive backing from your Rubber Feet.
3. Apply the Rubber Feet to each corner on the bottom of the Switch. These footpads
can prevent the Switch from shock/vibration.
Power On
Connect the power cord to the power socket on the rear panel of the Switch. The other
side of power cord connects to the power outlet. The internal power works with AC in the
voltage range 90-240VAC, frequency 50~60Hz. Check the power indicator on the front
panel to see if power is properly supplied.
9
Network Application
Desktop Application
The switch is designed to be a desktop size switch that is an ideal solution for small
workgroup. The Switch can be used as a standalone switch to which personal computers,
server, printer server are directly connected to form small workgroup.
Indoor & Protected Outdoor Application
IP based technologies start dominating outdoor applications, that have been historically
reserved for serial connectivity. Gigabit switches gradually leave traditional LANs and
become a backbone for infrastructure connectivity and management. MIL-SM8002TG
switches can interconnect IP-based Traffic control lights, Traffic Cameras and message
boards.
10
Console Management
Connecting to the Console Port
Use the supplied RS-232 cable to connect a terminal or PC to the console port. The
terminal or PC to be connected must support the terminal emulation program.
Connecting the switch to a terminal via RS-232 cable
Login in the Console Interface
When the connection between Switch and PC is ready, turn on the PC and run a terminal
emulation program or Hyper Terminal and configure its communication parameters to
match the following default characteristics of the console port:
Baud Rate: 9600 bps
Data Bits: 8
Parity: none
Stop Bit: 1
Flow control: None
11
The settings of communication parameters
After finished the parameter settings, click “OK“. When the blank screen shows up, press
Enter key to bring out the login prompt. Key in the root“(default value) for the both User
name and Password (use Enter key to switch), then press Enter key and the Main Menu
of console management appears. Please see below figure for login screen.
12
Console login interface
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180

Milan Technology MIL-SM8002TG User manual

Category
Network switches
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI