HP hp 355856-001 User manual

Hardware Reference Guide

HP Compaq Business Desktop d228 and

d248 Microtower

Document Part Number: 355856-001

November 2003

This guide provides basic information about upgrading this series of

computers.

The information contained herein is subject to change without notice.

Microsoft, MS-DOS, Windows, and Windows NT are trademarks of Microsoft

Corporation in the U.S. and other countries.

Intel, Pentium, Intel Inside, and Celeron are trademarks of Intel Corporation in

the U.S. and other countries.

Adobe, Acrobat, and Acrobat Reader are trademarks or registered trademarks of

Adobe Systems Incorporated.

The only warranties for HP products and services are set forth in the express

warranty statements accompanying such products and services. Nothing herein

should be construed as constituting an additional warranty. HP shall not be liable

for technical or editorial errors or omissions contained herein.

This document contains proprietary information that is protected by copyright.

No part of this document may be photocopied, reproduced, or translated to

another language without the prior written consent of Hewlett-Packard

Company.

Å

WARNING: Text set off in this manner indicates that failure to follow

directions could result in bodily harm or loss of life.

Ä

CAUTION: Text set off in this manner indicates that failure to follow

directions could result in damage to equipment or loss of information.

Hardware Reference Guide

HP Compaq Business Desktop d228 and d248 Microtower

TFirst Edition (November 2003)

Document Part Number: 355856-001

Hardware Reference Guide iii

Contents

1 Hardware Upgrades

Serviceability Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1

Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2

Removing the Access Panel and the Front Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2

Removing Front Drive Bezels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–5

5.25” Drive Bezel Blank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–5

Diskette Drive Bezel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–6

Installing Additional Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–7

DIMMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–7

DDR-SDRAM DIMMs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–7

Single Channel and Dual Channel Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–8

Installing Memory Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–9

Installing an Expansion Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–11

Replacing or Upgrading a Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–13

Drive Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–14

Removing a 5.25” Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–15

Removing a Diskette Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–16

Removing the Lower Drive Cage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–17

Removing a 3.5” Hard Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–19

2 Battery Replacement

Replacing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1

3 Routine Care & Shipping Information

Routine Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1

Optical Disk Drive Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2

Shipping Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–3

iv Hardware Reference Guide

Contents

4 Electrostatic Discharge

Preventing Electrostatic Damage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1

Grounding Methods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–2

Index

Hardware Reference Guide 1–1

1

Hardware Upgrades

HP Compaq d228, d230, and d248 Microtower

Serviceability Features

The Microtower computer includes features that make it easy to

upgrade and service. No tools are needed for most of the installation

procedures described in this chapter.

1–2 Hardware Reference Guide

Hardware Upgrades

Warnings and Cautions

Before performing upgrades be sure to carefully read all of the

applicable instructions, cautions, and warnings in this guide.

Å

WARNING: To reduce the risk of personal injury from electrical shock

and/or hot surfaces, be sure to disconnect the power cord from the wall

outlet and allow the internal system components to cool before touching.

Å

WARNING: To reduce the risk of electrical shock, fire, or damage to the

equipment, do not plug telecommunications/telephone connectors into the

network interface controller (NIC) receptacles.

Ä

CAUTION: Static electricity can damage the electrical components of the

computer or optional equipment. Before beginning these procedures,

ensure that you are discharged of static electricity by briefly touching a

grounded metal object. See Chapter 4, “Electrostatic Discharge” for more

information.

Ä

CAUTION: Before removing the computer cover, ensure that the

computer is turned off and that the power cord is disconnected from the

electrical outlet.

Removing the Access Panel and the Front Bezel

1. Turn off the computer properly through the operating system and

turn off any external devices.

2. Disconnect the power cord from the power outlet and the

computer, and disconnect any external devices.

3. Remove the two screws that secure the access panel to the

computer chassis. Some access panels use captive thumbscrews.

✎

Remove the right access panel to upgrade memory or an expansion

card.

Remove the left access panel to upgrade a drive.

Hardware Reference Guide 1–3

Hardware Upgrades

4. Slide the access panel back about 1 inch (2.5 cm), then lift it away

from and off the unit.

Removing the Access Panels

To replace the access panel, reverse the removal steps.

✎

The two access panels are physically identical. One access panel has

captive thumbscrews that may be removed by unscrewing them.

1–4 Hardware Reference Guide

Hardware Upgrades

5. To remove the front bezel, grasp the bottom of the front panel

below the lowest air vent and pull the panel out and up to release

it from the chassis.

Removing the Front Bezel

To install the front bezel, insert the top two latches into their

respective holes in the chassis and push the bezel in until it is fully

seated.

✎

When replacing the front bezel, ensure that the top of the front bezel

is flush with the top of the chassis before pressing it into place.

Hardware Reference Guide 1–5

Hardware Upgrades

Removing Front Drive Bezels

1. Turn off the computer properly through the operating system and

turn off any external devices.

2. Disconnect the power cord from the power outlet and the

computer, and disconnect any external devices.

3. Remove the access panel.

4. Remove the front bezel.

5.25” Drive Bezel Blank

Press one of the retaining tabs on the inside of the large bezel towards

the outer edge of the bezel to release the bezel blank. At the same

time, pull the bezel blank inwards to remove it from the main bezel.

Removing the Bezel Blank

To install a bezel blank, reverse the removal procedure.

1–6 Hardware Reference Guide

Hardware Upgrades

Diskette Drive Bezel

✎

Depending on the computer configuration, you may have a bezel

blank in this position. If you do not have a drive in this slot, you may

choose to install a 3.5-inch device (such as a diskette drive, hard

drive, or Zip drive) later on.

Pull the right retaining tab towards the center of the main bezel. At

the same time, pull the bezel inwards to remove it from the main

bezel.

Removing the Bezel Blank

To install a diskette drive bezel, reverse the removal procedure.

Hardware Reference Guide 1–7

Hardware Upgrades

Installing Additional Memory

The computer comes with Double Data Rate-Synchronous Dynamic

Random Access Memory (DDR-SDRAM) Dual Inline Memory

Modules (DIMMs).

DIMMs

The memory sockets on the system board can be populated with

industry-standard DIMMs. These memory module slots are populated

with at least one preinstalled memory module. To achieve the

maximum memory support, you may be required to replace the

preinstalled DIMM with a higher capacity DIMM.

The HP Compaq d228 and d230 Microtower system boards can be

populated with up to 2GB of memory and support single-channel

mode. The HP Compaq d248 Microtower system board can be

populated with up to 4GB of memory and supports single-channel or

dual-channel mode.

✎

For more information about single-channel or dual-channel memory

modes, see the section “Single Channel and Dual Channel Modes” on

page 8.

DDR-SDRAM DIMMs

For proper system operation, if the computer supports DDR-SDRAM

DIMMs, the DIMMs must be:

■ industry-standard 184-pin

■ unbuffered PC2100 266 MHz-, PC2700 333 MHz-, or PC3200

400 MHz-compliant

✎

Only the HP Compaq d248 Microtower supports PC3200 400

MHz-compliant DIMMS.

■ 2.5 volt DDR-SDRAM DIMMs.

The DDR-SDRAM DIMMs must also:

■ support CAS latency 2, 2.5, or 3 (CL = 2, CL = 2.5, or CL = 3)

1–8 Hardware Reference Guide

Hardware Upgrades

■ contain the mandatory JEDEC SPD information

In addition, the computer supports:

■ 128Mbit, 256Mbit, and 512Mbit non-ECC memory technologies

■ single-sided and double-sided DIMMS

■ DIMMs constructed with x8 and x16 DDR devices; DIMMs

constructed with x4 SDRAM are not supported

Maximum operating speed is determined by a combination of the

CPU and type of memory used. Refer to the table below for the

optimum combination.

✎

The system will not start if you install unsupported DIMMs.

Single Channel and Dual Channel Modes

HP Compaq d228 and d230 Microtower models operate in single

channel mode. HP Compaq d248 Microtower models will

automatically operate in single channel mode or a higher-performing

dual channel mode, depending on how the DIMMs are installed.

■ In single channel mode, the maximum operational speed is

determined by the slowest DIMM in the system. For example, if

the system is populated with a DIMM that is 266 MHz and a

second DIMM that is 333 MHz, the system will run at the slower

of the two speeds.

■ In dual channel mode (d248 models only), all DIMMs must be

identically matched. DIMMs in the J23 and J24 sockets must be

identical; DIMMs in the J25 and J28 sockets must also be

Maximum Front Side Bus Operating Speed (MHz)

CPU Front Side Bus

(MHz)

DDR266

DIMM

DDR333

DIMM

DDR400

DIMM

400 266 266 266

533 266 333 333

800 (d248 only) 266 320 400

Hardware Reference Guide 1–9

Hardware Upgrades

identical. Therefore, if you have one preinstalled DIMM in socket

J23 and are adding a second DIMM, it is recommended that you

install an identical DIMM into the J25 socket. If you are

populating all four DIMM sockets, use identical DIMMs in each

socket. Otherwise, the system will not operate in dual channel

mode.

There are two DIMM sockets on the HP Compaq d228 and d230

Microtower system board, operating in single-channel mode.

There are four DIMM sockets on the HP Compaq d248 Microtower

system board, operating in either single- or dual-channel mode, with

two sockets per channel. The sockets are labeled J23, J24, J25, and

J28. Sockets J23 and J24 operate in memory channel A. Sockets J25

and J28 operate in memory channel B.

Installing Memory Modules

Ä

CAUTION: The memory module sockets have gold metal contacts. When

upgrading the memory, it is important to use memory modules with gold

metal contacts to prevent corrosion and/or oxidation resulting from having

incompatible metals in contact with each other.

Ä

CAUTION: Static electricity can damage the electronic components of

the computer or optional cards. Before beginning these procedures,

ensure that you are discharged of static electricity by briefly touching a

grounded metal object. Refer to Chapter 5 for more information.

Ä

CAUTION: When handling a memory module, be careful not to touch

any of the contacts. Doing so may damage the module.

1. Turn off the computer properly through the operating system and

turn off any external devices.

2. Disconnect the power cord from the power outlet and the

computer, and disconnect any external devices.

✎

If there is a hard drive in bay 5 it will be necessary to remove the

lower drive cage before removing the memory modules.

3. Remove the right access panel.

1–10 Hardware Reference Guide

Hardware Upgrades

Å

WARNING: To reduce risk of personal injury from hot surfaces, allow

the internal system components to cool before touching.

4. Lay the computer down on its side to make it easier to work on.

5. Open both latches of the memory module socket 1, and insert the

memory module into the socket 2. Begin by installing a module

into the socket nearest the preinstalled module, and install the

modules following the numerical order of the sockets.

Installing a Memory Module

✎

A memory module can be installed in only one way. Match the notch

on the module with the tab on the memory socket.

6. Push the module down into the socket, ensuring that the module

is fully inserted and properly seated. Make sure the latches are in

the closed position 3.

7. Repeat steps 5 and 6 for any additional modules that you want to

install.

To reassemble the computer, reverse the removal procedure.

Hardware Reference Guide 1–11

Hardware Upgrades

Installing an Expansion Card

1. Turn off the computer properly through the operating system and

turn off any external devices.

2. Disconnect the power cord from the power outlet and the

computer, and disconnect any external devices.

3. Remove the right access panel.

4. Lay the computer down on its side to make it easier to work on.

If installing an expansion card in an empty slot, skip to step 10.

5. To remove an expansion card, disconnect any cables attached to

the expansion card.

6. Remove the screw at the top of the expansion slot.

7. Hold the card at each end and carefully rock it back and forth

until the connectors pull free from the socket. Be sure not to

scrape the card against other components.

8. Store the card in anti-static packaging.

9. Install a new expansion card or an expansion slot cover to close

the open slot.

Ä

CAUTION: After removing an expansion card, you must replace it with a

new card or cover the open slot (for example, with a metal slot cover or a

piece of duct tape) for proper cooling of internal components during

operation.

1–12 Hardware Reference Guide

Hardware Upgrades

If not installing an additional expansion card, skip to step 12.

10. Remove the expansion slot cover.

11. Slide the expansion card into the expansion socket and press it

firmly into place.

Installing an Expansion Card

✎

When you install an expansion card, make sure you press firmly on

the card so that the entire connector seats properly in the expansion

card socket.

12. Install the screw at the top of the expansion slot to further secure

the part in the chassis.

13. Replace the access panel.

14. Connect external cables to the installed card, if needed.

Reconfigure the computer, if necessary.

Hardware Reference Guide 1–13

Hardware Upgrades

Replacing or Upgrading a Drive

The computer supports up to five drives that may be installed in

various configurations.

This Section describes the procedure for replacing or upgrading the

storage drives. A Torx T-15 screwdriver is needed to remove and

install the guide screws on a drive.

Ä

CAUTION: Make sure personal files on the hard drive are backed up to

an external storage device before removing the hard drive. Failure to do

so will result in data loss. After replacing the primary hard drive, you will

need to run the Restore Plus! CD to load the Compaq factory-installed

files.

1–14 Hardware Reference Guide

Hardware Upgrades

Drive Positions

Description Description

1 2 5.25-inch drive bay for optional drives*

3 3.5-inch drive bay (1.44-MB diskette drive shown)**

4 5 3.5-inch, internal, standard hard drive bay

*An optional drive is a CD-ROM, CD-R/RW, DVD-ROM,

DVD-R/RW, or CD-RW/DVD Combo drive.

**Depending on the computer configuration, you may have a

bezel blank in this position. If you do not have a drive in this slot,

you may choose to install a 3.5-inch device (such as a diskette

drive, hard drive, or Zip drive) later on.

Hardware Reference Guide 1–15

Hardware Upgrades

Removing a 5.25” Drive

1. Turn off the computer properly through the operating system and

turn off any external devices.

2. Disconnect the power cord from the power outlet and the

computer, and disconnect any external devices.

3. Remove both the right and left access panels.

4. Remove the front bezel.

5. Disconnect the power, data, and audio cables, as necessary, from

the back of the drive.

✎

In some cases it may be easier to slide the drive part way out of the

drive bay before removing the cables.

6. Remove the four screws, two from each side, that secure the drive

in the drive cage 1.

7. Slide the drive out of the drive cage, as shown in the illustration

below 2.

Removing a 5.25” Drive

1–16 Hardware Reference Guide

Hardware Upgrades

To install a drive, reverse the removal procedure.

✎

If you are installing a 5.25” drive for the first time into bay 2 you must

first remove the drive from bay 1 and then knock or pry out the metal

shield that covers the front of bay 2.

Å

WARNING: There may be sharp edges on the inside of the bay opening

after the shield has been removed.

Removing a Diskette Drive

1. Turn off the computer properly through the operating system and

turn off any external devices.

2. Disconnect the power cord from the power outlet and the

computer, and disconnect any external devices.

3. Remove both the right and left access panels.

4. Remove the front bezel.

5. Disconnect the power, and data cables from the back of the drive.

Page is loading ...

HP hp 355856-001 User manual

This manual is also suitable for

HP hp 355856-001 User manual

Related papers

Other documents