Graco 307751F Owner's manual

Graco
Brand
Graco
Model
307751F
Category
Paint Sprayer
Type
Owner's manual

This manual is also suitable for

Graco 307751F Circulating 'Y' Restrictor Valve is designed to restrict fluid flow to the gun in a circulating system. It is compatible with water-base fluids and has a maximum inbound fluid pressure of 300 psi (21 bar). The valve comes with various models and port sizes, allowing you to choose the one that best suits your needs. It features a twist-lock coupler or a 3/8 npsm swivel coupler for easy connection and disconnection. The valve also includes an adjustment tool that enables you to adjust the fluid flow to your desired level.

Graco 307751F Circulating 'Y' Restrictor Valve is designed to restrict fluid flow to the gun in a circulating system. It is compatible with water-base fluids and has a maximum inbound fluid pressure of 300 psi (21 bar). The valve comes with various models and port sizes, allowing you to choose the one that best suits your needs. It features a twist-lock coupler or a 3/8 npsm swivel coupler for easy connection and disconnection. The valve also includes an adjustment tool that enables you to adjust the fluid flow to your desired level.

This manual contains
IMPORTANT
WARNINGS AND INSTRUCTIONS
READ AND RETAIN FOR REFERENCE
INSTRUCTIONS–PARTS
LIST
307–751
Rev. F
Supersedes
E
Tamper-Resistant
CIRCULATING
‘Y’ RESTRICT
OR V
ALVE
300 psi (21 bar) MAXIMUM INBOUND FLUID PRESSURE
Restricts
fluid flow to the gun in a circulating system
Compatible with water-base fluids.
Model 223–617, Series B
1/4
npsm inlet and return ports;
T
wist-lock coupler
Model 223–618, Series B
3/8
npsm inlet and return ports;
T
wist-lock coupler
Model 223–619, Series B
1/4
npsm inlet and return port;
3/8 npsm swivel coupler
Model 223–620, Series B
3/8
npsm inlet and return ports;
3/8 npsm swivel coupler
U.S. Patent No. 4,615,485
U.K. Patent No. 2,176,265
Foreign Patents Pending
WETTED
P
ARTS:
Stainless steel, Acetal,
Homopolymer
, PTFE
.
INSTALLATION & OPERATION
WARNING
This
valve is for use ONL
Y in low pressure circulat
-
ing systems. To reduce the risk of serious bodily
injury, which could result from over-pressurizing
and
rupturing the valve, NEVER supply more
than
300
psi (21 bar) fluid pressure to the valve.
To
reduce the risk of splashing,
always relieve the
air and fluid pressure to the gun before removing
this
valve for any reason.
Connect the circulating fluid hoses to the valve.
Connect the valve to the gun.
For twist-lock couplers,
align the pins on the stem with
the coupler slots and push the coupler onto the stem.
Turn
the stem clockwise to lock it.
T
o adjust the fluid flow
,
insert the adjustment tool (A) as
shown
in
Fig 1. T
urn the tool clockwise to decrease flow
and
counterclockwise to increase flow
.
Fig 1
A
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
COPYRIGHT 1990 GRACO INC.


 

  
1
1

SERVICE
Before removing the restrictor from the system, shut off
the
power to the pump and
relieve air and fluid pressure.
Remove
the coupler from the valve. Pry out the packing
cartridge (2
or 7). See Parts Drawing. Thoroughly clean
the valve and install a new cartridge. Reinstall the cou-
pler.
If
your valve has a twist lock coupler
,
position
the slot in
the housing on the center line of the valve. See Fig 2.
Tighten
the nut (5) firmly to 15 to 25 ft-lb (20 to 34 N
m).
If you
are replacing the inlet and return adapters (1),
ap
-
ply
thread sealant to the threads
of the new adapters be
-
fore installing, and torque
to 15
to 25 ft-lb (20 to 34 N
m).
See
Parts Drawing.
Fig 2
5
Torque
to
15 to 25 ft-lb
(20 to 34 N
m)
PARTS
DRA
WING AND LIST
5
4
3
2a
2b
2c
2d
2e
6
7
1
Torque
to
15 to 25 ft-lb
(20 to 34 N
m)
Apply sealant
T
orque to
15 to 25 ft-lb
(20 to 34 N
m)
Not Sold
Separately
2
SERVICE NOTE:
Series letter changed on all models.
Model 223–617 and 223–618 Series A
W
ith T
wist-lock Coupler
REF
NO. PART NO. DESCRIPTION QTY
171–234
ADAPTER, 1/4 npsm;
Model 223–617
2
180–403
ADAPTER, 3/8 npsm;
Model 223–618
2
2* 220–103 CARTRIDGE, packing;
Includes items 2a to 2e
1
2a 178–846
SEAL 1
2b 178–848
SEAT
, ball
1
2c 111–279
BALL 1
2d 168–890
SPRING, compression 1
2e 181–282
SLEEVE 1
3 178–847 GUIDE, coupler stem 1
4 186–202 HOUSING, coupling 1
5 186–203 NUT
, coupling
1
Model 223–619 and 223–620 Series A
W
ith Swivel Coupler
REF
NO. PART NO. DESCRIPTION QTY
171–234
ADAPTER, 1/4 npsm;
Model 223–619
2
180–403
ADAPTER, 3/8 npsm;
Model 223–620
2
6 223–892 UNION, 3/8 npsm swivel x 3/8 npt(f) 1
7* 181–283 CARTRIDGE, packing 1
*Keep on hand to reduce down time
ACCESSORIES
Accessories
must be purchased separately
Adjustment Tool 220–102
Required
for adjusting the restrictor valve.
Coupler Stem 204–891
Required to adapt the 3/8 npsm(m) fluid inlet of the air
spray
gun for use with twist-lock coupler
Sales
Offices:
Atlanta, Chicago, Dallas, Detroit, Los Angeles, Mt. Arlington (N.J.)
Foreign Offices:
Canada; England; Korea; Switzerland; France; Germany; Hong Kong; Japan
GRACO
INC.
P
.O. BOX 1441
MINNEAPOLIS, MN
55440–1441
PRINTED
IN U.S.A.
307–751 10/85 Revised 3–93
  • Page 1 1
  • Page 2 2

Graco 307751F Owner's manual

Graco
Brand
Graco
Model
307751F
Category
Paint Sprayer
Type
Owner's manual
This manual is also suitable for

Graco 307751F Circulating 'Y' Restrictor Valve is designed to restrict fluid flow to the gun in a circulating system. It is compatible with water-base fluids and has a maximum inbound fluid pressure of 300 psi (21 bar). The valve comes with various models and port sizes, allowing you to choose the one that best suits your needs. It features a twist-lock coupler or a 3/8 npsm swivel coupler for easy connection and disconnection. The valve also includes an adjustment tool that enables you to adjust the fluid flow to your desired level.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents