LG 26LH1DC3 User manual

Brand: LG

Model: 26LH1DC3

Category: LCD TVs

Type: User manual

This manual is also suitable for

Please read this manual carefully before operating

your set.

Retain it for future reference.

Record model number and serial number of the set.

See the label attached on the back cover and quote

this information to your dealer when you require

service.

Installation and

Operating Guide

26LH1DC3

26LH1DC4

26LH1DC5

www.lgcommercial.com

WARNING / CAUTION

REGULATORY INFORMATION

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference when the

equipment is operated in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instruction manual, may cause

harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV

technician for help.

IT IS FORBIDDEN TO CONNECT THIS TV

TO ANY TELECOMMUNICATION

NETWORK / TELEPHONE.

The exclamation point within an

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance (servicing) instructions

in the literature accompanying the appliance.

The lightning flash with arrowhead

symbol, within an equilateral triangle, is

intended to alert the user to the

presence of uninsulated “dangerous voltage”

within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of

electric shock to persons.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER TO

QUALIFIED SERVICE PERSONNEL.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT

EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

THIS PRODUCT MUST BE USED WITH UL LISTED

MOUNTING BRACKET.

This reminder is provided to call the CATV system installer’s

attention to Article 820-40 of the National Electric Code

(U.S.A.). The code provides guidelines for proper

grounding and, in particular, specifies that the cable ground

shall be connected to the grounding system of the building,

as close to the point of the cable entry as practical.

NOTE TO CABLE TV INSTALLER

Changes or modifications not expressly approved by the

party responsible for compliance could void the user’s

authority to operate the equipment.

CAUTION

THE PARTY RESPONSIBLE FOR PRODUCT

COMPLIANCE

(LG Electronics U.S.A., Inc.,)

(2000 Millbrook Drive)

(TELEPHONE NO:1-847-941-8000)

Do not attempt to modify this product in any way

without written authorization from LG Electronics

Corporation.

Unauthorized modification could void the user’s

authority to operate this product.

CAUTION

Apparatus shall not be exposed to dripping or

splashing and no objects filled with liquids, such as

vases, shall not be placed on the apparatus.

WARNING

THESE SERVICING INSTRUCTIONS ARE FOR USE BY

QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE

THE RISK OF ELECTRIC SHOCK, DO NOT PERFORM

ANY SERVICING OTHER THAN THAT CONTAINED

IN THE OPERATING INSTRUCTIONS UNLESS YOU

ARE QUALIFIED TO DO SO.

CAUTION

When used outside of the U.S., it may be used HAR

cord with fitting of an approved agency is employed.

(When used outside of U.S., other power supply cords

may be used if the cord is approved by the local

regulating agency.)

CAUTION

YOUR PRODUCT HAS BEEN MANUFACTURED AND TESTED WITH YOUR SAFETY IN MIND. HOWEVER,

IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. TO AVOID DEFEATING

THE SAFEGUARDS THAT HAVE BEEN BUILT INTO YOUR NEW PRODUCT, PLEASE READ AND OBSERVE THE

FOLLOWING SAFETY POINTS WHEN INSTALLING AND USING YOUR NEW PRODUCT, AND SAVE THEM FOR

FUTURE REFERENCE. OBSERVING THE SIMPLE PRECAUTIONS DISCUSSED IN THIS MANUAL CAN HELP YOU

GET MANY YEARS OF ENJOYMENT AND SAFE OPERATION THAT ARE BUILT INTO YOUR NEW PRODUCT.

IMPORTANT SAFEGUARDS FOR YOU AND YOUR NEW PRODUCT

Clean the exterior of this television by removing dust

with a lint-free cloth.

CAUTION: To avoid damage to the surface of the

television, do not use abrasive or chemical cleaning

agents.

CLEANING AND DISINFECTION

If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is

nothing wrong with the TV.

Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots.

However, they have no adverse effect on the TVs performance.

Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may

produce some temporary distortion effects on the screen.

NOTE

SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or

the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

10 .Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11 . Only use attachments/accessories specified by the manufacturer.

12 .Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13 . Unplug this apparatus during lightning storms or when unused for long periods of time.

14 .Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in

any way, such as power-supply cord or plug is damaged, liquid has been spilled or object have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded

so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National

Electrical Code (U.S.A.), ANSI/NFPA 70 provides information with regard to proper grounding of the mast and

supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors,

location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding

electrode.

Example of Grounding According to National Electrical Code Instructions

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductor

(NEC Section 810-21)

Ground Clamps

Power Service Grounding

Electrode System (NEC

Art 250, Part H)

Ground Clamp

Electric Service

Equipment

NEC - National Electrical Code

PORTABLE CART WARNING

CONTENTS

Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . 10

HD Receiver Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

DVD Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

VCR Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Other A/V Source Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Digital Audio Output

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

PC Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Screen Setup for PC mode

. . . . . . . . . . . . . . . . . . . . . . . . . . 21

DV I Hookup To RJP or DVD Player . . . . . . . . . . . . . . . 22

Computer PC Hookup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

EXTERNAL EQUIPMENT SETUP

User Remote Control Button Functions . . . . . . . . . 23

Installer Remote Control Button Functions . . . . 24

On-Screen Menus Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . 25

Channel Search

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

WATCHING TV /CHANNEL CONTROL

Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Daylight Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Time Zone Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

TV Activation Time Settings

. . . . . . . . . . . . . . . . . . . 33

TV Deactivation Time Settings

. . . . . . . . . . . . . . . 33

Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

TIME SETTING

WARNING / CAUTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . 4

CONTENTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Accessories

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

VESA Wall Mounting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

PREPARATION

Set Password & Lock System

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Movie & TV Ratings

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PARENTAL CONTROL/RATINGS

Caption / Text

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Preset Sound Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Sound Setting Adjustment-user Mode . . . . . 43

Sound Balance Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Digital Audio Output Settings . . . . . . . . . . . . . 44

Aautomatic Volume Control Settings . . . . 45

Analog Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . 45

Digital Audio Language Settings . . . . . . . . . . . . 46

Using External Speakers . . . . . . . . . . . . . . . . . . . . . . 46

Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Menu Transparency Settings . . . . . . . . . . . . . . . . . . 48

Set ID

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

SOUND & LANGUAGE CONTROL

Preset Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Screen Format Adjustments . . . . . . . . . . . . . . . . . 50

Noise Reduction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Film Mode Options . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

PICTURE CONTROL

Tr oubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Cloning Procedure Troubleshooting

. . . . . . . . . . . . . . .71

Clone Troubleshooting Flow Chart . . . . . . . . . . . . . . . .73

TV Operating Check

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Installer Quick Setup Guide . . . . . . . . . . . . . . . . . . . . . . . . . 76

APPENDIX

Installer Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Commercial Mode Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Cloning Connections/Learning Setup . . . . . . . . . . . . .54

Clone Programmer/Learning Setup

. . . . . . . . . . . . . . .55

Cloning Connections/Teaching Setup

. . . . . . . . . . . . .56

Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Peference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

COMMERCIAL MODE

PREPARATION

ACCESSORIES

Ensure that the following accessories are included with your product. If an accessory is missing, please contact the

dealer where you purchased the product.

User must use shielded signal interface cables with ferrite cores to maintain standard compliance for the product.

Owner’s Manual CD Manual

Power Co rd

Shown herein is an optional Installer remote control available for the 26LH1DC3/4/5 models only. The

installer remote control is NOT included with the TV.

•However, the user's remote is included with the TV.

To perform a normal installation set up, you need an installer's remote and the LT2002 Quickset II Clone

Programmer – both are shown and described in later sections. See your LG dealer if you wish to purchase

the Installer remote and LT2002. The installer remote allows access to the Installer menus, User menus in

the Manual Channel Set options on the Setup menu. The installer remote has Menu, Select, and Adjust

Keys. The LT2002 Quickset II Clone Programmer is used to duplicate a TV's setup and install it on another

identical TV.

Optional Installer Remote Control for Model No. Series 26LH1DC3/4/5

Purchase the Optional Installer's Remote and Clone Programmer

User Remote Control.

Batteries

Installer Remote Control.

Batteries (Optional )

POWERMUTE

TV/AV

PREVIEW

GUIDE

SAP INFO

123

456

TIMER

FLASHBK

VOL

ALARM

Design and specifications are subject to change without prior notice.

NOTE

PREPARATION

FRONT PANEL INFORMATION

On-Screen Displays

See descriptions on page 25. On-screen displays will appear when the feature

is active or the function is being used.

Use the VV OOLL (Volume) Up/Down button to

adjust the sound level to your preference.

Use the CC HH (Channel) Up/Down button to

cycle through the available channels.

Displays the current channel bank. Press

again to change banks.

Press MMEENNUU repeatedly to scroll through

menus.

TV Operation

Press the PPOOWWEERR button to turn the TV

on from standby mode.

Power / Standby Indicator

Glows red in Standby mode.

Glows green when the TV is

turned on.

Glows orange in Sleep Timer

and/or Alarm mode.

/ I

LED Color Action/Status

RED Power is Off (Standby)

GREEN is flashing Power On sequence is processing

GREEN Power is On

ORANGE If Power is Off On Timer is set or Alarm is set

If Power is On Off Timer is set or Sleep Timer is set

/ I

CDE

■

Here shown may be somewhat different from your TV.

■

Using the front control panel to operate the TV.

Front Panel Controls

Remote Control Sensor

With Installer menu item 11 buttons Defeat

set to 000 (the default setting), Menu and

TTVV //AAVV buttons are disabled.

NOTE

PREPARATION

Back Connection Panel

M.P.I. INTERFACE

Use with clone programmer.

FUTURE USE

DVI/PC AUDIO IN

PC IN

HDMI/DVI IN

DIGITAL AUDIO OUT

(Optical)

RS-232C PORT

RS-232C SELECT

SWITCH

UPDATE SWITCH

ANTENNA CABLE

Connect to an antenna or

cable system.

S-VIDEO IN

AUDIO / VIDEO 1, 3 IN

Connect Audio / Video

equipment to these jacks.

COMPONENT 1, 2 IN

AC IN

RJP INTERFACE

VIDEO2(SIDE AUTO-CAMPORT)

VIDEO IN AUDIO IN

AUDIO/

VIDEO 2

(SIDE

AUTO-

CAMPORT)

PREPARATION

BACK PANEL INFORMATION

■

Here shown may be somewhat different from your TV.

RS-232C, Update Switch and RS-232C Select Switch are reserved for qualified and authorized service and

technical support personal only.

NOTE

PREPARATION

VESA WALL MAUNTING

There are several Vesa standard

mounts available that can be used

with this TV. The mount shown to the

right would be installed on the TV

back using required bolts in the four

pre-threaded holes provided.

Follow any instructions supplied with

the Vesa mount if one is to be used

for the TV installation.

Swivel Stand

- The TV can be conveniently

swiveled on its stand 30° to

the left or right to provide

optimum viewing angles.

■

Here shown may be somewhat different from your TV.

TV Swivel Stand

Vesa Standard

Mounting Holes

Typical

Vesa

Mount

EXTERNAL EQUIPMENT SETUP

ANTENNA OR CABLE CONNECTION

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections.

For optimum picture quality, adjust antenna direction if needed.

Wall

Antenna

Socket

Outdoor

Antenna

(VHF, UHF)

Multi-family Dwellings/Apartments

(Connect to wall antenna socket)

RF Coaxial Wire (75 ohm)

Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna)

Be careful not to bend the bronze wire

when connecting the antenna.

Copper Wire

2. Cable

Cable TV

Wall Jack

RF Coaxial Wire (75 ohm)

■

To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

■

If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

■

If the antenna is not installed properly, contact your dealer for assistance.

Antenna

UHF

Signal

Amplifier

VHF

3. Using both cable and antenna

Cable TV

Wall Jack

Antenna

RF Coaxial Wire (75 ohm)

Diplexer

(Signal

Combiner)

The TV will let you know when the analog, cable, and digital channel scans are complete.

NOTE

EXTERNAL EQUIPMENT SETUP

HD RECEIVER SETUP

This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do

receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

L R Y PB PR

When connecting Component cable

1. How to connect

Connect the audio output of the digital set-top box to

the CCOOMMPPOONN EENNTT((DDVVDD//DDTTVV))11 jacks on the set.

Connect the video outputs (Y, PB, PR) of the digital set

top box to the CCOOMM PPOONNEENNTT((DDVVDD//DDTTVV))11 jacks on

the set. Match the jack colors

(Y = green, PB = blue, and PR = red).

2. How to use

■

Turn on the digital set-top box.

(Refer to the owner’s manual for the digital set-top box.

operation)

■

Select CCoommppoonneenntt11 input source by using the TTVV//AAVV

button on the remote control.

■

If connected to CCOOMMPPOONN EENNTT((DDVV DD//DDTTVV))22 input,

select CCoommppoonneenntt22 input source.

■

To prevent the equipment damage, never plug in any power cords until you have finished connecting all

equipment.

Signal

480i

480p

720p

1080i

Component 1/2

Yes

HDMI1/DVI,

HDMI2

Yes

EXTERNAL EQUIPMENT SETUP

When connecting HDMI cable

No separated audio connection is necessary.

HDMI supports both audio and video.

Connect the digital set-top box to HHDDMMII//DDVVII IINN jack on

the set.

1. How to connect

2. How to use

■

Turn on the digital set-top box.

(Refer to the owner’s manual for the digital set-top box.)

■

Select HHDDMMII input source by using the TT VV //AA VV button

on the remote control.

When connected, the TV will tell a connected device what

resolution it supports and the resolution it prefers. If the device

supports this Auto HDMI function, the player output resolution

will be automatically set to 720p.

If the device does not support Auto HDMI, you need to set the

output resolution appropriately.

NOTE

EXTERNAL EQUIPMENT SETUP

Connect the audio output of the digital set-top box to

the DDVVII//PPCC AAUUDDIIOO IINN jack on the set.

Connect the DVI output of the digital set-top box to the

HHDDMMII//DDVVII IINN jack on the set.

1. How to connect

■

Turn on the digital set-top box. (Refer to the owner’s

manual for the digital set-top box.)

■

Select HHDDMMII input source by using the TT VV //AA VV button

on the remote control.

2. How to use

When connecting HDMI to DVI cableWhen connecting HDMI to DVI cable

EXTERNAL EQUIPMENT SETUP

DVD SETUP

When connecting Component cable

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component Input ports

Component ports on the TV

YPB PR

Video output ports

on DVD player

B-Y

R-Y

Connect the audio outputs of the DVD to the

CC OOMMPPOONNEENNTT((DDVVDD//DDTTVV ))11 jacks on the set.

Connect the video outputs (Y, PB, PR) of the DVD to

the CCOOMMPPOONNEE NNTT ((DDVVDD//DDTTVV ))11 jacks on the set.

Match the jack colors

(Y = green, PB = blue, and PR = red).

1. How to connect

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select CCoommppoonneenntt11 input source by using the TT VV //AAVV

button on the remote control.

■

If connected to CCOOMMPPOONNEENNTT((DDVVDD//DDTT VV))22 input,

select CCoommppoonneenntt22 input source.

■

Refer to the DVD player's manual for operating instructions.

L R Y PB PR

EXTERNAL EQUIPMENT SETUP

When connecting with an S-Video cable

When connecting HDMI cable

No separated audio connection is necessary.

HDMI supports both audio and video.

Connect the HDMI output of the DVD to the

HHDDMMII//DDVVII IINN jack on the set.

1. How to connect

2. How to use

■

Select HHDDMMII input source by using the TTVV// AAVV button on

the remote control.

■

Refer to the DVD player's manual for operating instructions.

When connected, the TV will tell a connected device what

resolution it supports and the resolution it prefers. If the device

supports this Auto HDMI function, the player output resolution

will be automatically set to 720p.

If the device does not support Auto HDMI, you need to set the

output resolution appropriately.

To get the best picture quality, adjust the output resolution of

the DVD to 720p.

NOTE

Connect the audio outputs of the VCR to the AA UU DD II OO

input jacks on the set.

Connect the S-VIDEO output of the VCR to the

SS--VV IIDD EEOO input on the set.

1. How to connect

EXTERNAL EQUIPMENT SETUP

VCR SETUP

When connecting with an antenna

■

To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

■

If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen.

This phenomenon is common to all manufactures and in consequence the manufactures warranty does not cover

the product bearing this phenomenon.

L R

S-VIDEO VIDEO

OUTPUT

SWITCH

ANT IN

ANT OUT

Wall Jack

Antenna

Connect the antenna cable to the RF antenna

in socket of the VCR.

Connect the RF antenna out socket of the

VCR to the AANNTTEENNNNAA//CCAABBLLEE socket on

the set.

1. How to connect

■

Set VCR output switch to 3 or 4 and then tune

TV to the same channel number.

■

Insert a video tape into the VCR and press PLAY

on the VCR. (Refer to the VCR owner’s manual.)

2. How to use

EXTERNAL EQUIPMENT SETUP

When connecting with a RCA cable

Connect the VVIIDDEEOO11 jacks between TV and VCR. Match

the jack colors (Video = yellow, Audio Left = white, and

Audio Right = red)

1. How to connect

2. How to use

■

Insert a video tape into the VCR and press PLAY on the

VCR. (Refer to the VCR owner’s manual.)

■

Select AA VV 11 input source by using the TT VV // AAVV button on

the remote control.

■

If connected to VVIIDDEEOO33, select AA VV 33 input source.

When connecting with an S-Video cable

Connect the audio outputs of the VCR to the AA UU DD IIOO

IINN jacks on the set.

Connect the S-VIDEO output of the VCR to the

SS--VV IIDD EEOO input on the set.

1. How to connect

2. How to use

■

Insert a video tape into the VCR and press PLAY on the

VCR. (Refer to the VCR owner’s manual.)

■

Select SS-- VV II DD EEOO input source by using the TT VV //AAVV but-

ton on the remote control.

1 2

The picture quality is improved: compared to normal

composite (RCA cable) input.

NOTE

Do not connect to both Video and

S-Video at the same time. In the

event that you connect both

Video and the S-Video cables, only

the S-Video will work.

CAUTION

EXTERNAL EQUIPMENT SETUP

OTHER A/V SOURCE SETUP

Connect the VVIIDDEEOO22 jacks between

TV and external equipment. Match the

jack colors.

(Video = yellow, Audio Left = white, and

Audio Right = red)

1. How to connect

2. How to use

■

Select AA VV 22 input source by using the TT VV //AAVV

button on the remote control.

■

Operate the corresponding external equipment.

■

Send the TV’s audio to external audio equipment via the Digital Audio Output (Optical) port.

Connect the other end of the optical cable to the

digital audio (optical) input on the audio equipment.

Set the “Digital Output - Dolby Digital” in the Sound

menu. (G p.44). See the external audio equipment

instruction manual for operation.

Connect one end of an optical cable to the TV Digital

Audio (Optical) Output port.

1. How to connect

DIGITAL AUDIO OUTPUT

When connecting with external audio equipments, such

as amplifiers or speakers, please turn the TV speakers

off. (G p.46)

NOTE

Do not look into the optical output port. Looking at the

laser beam may damage your vision.

CAUTION

Camcorder

Video Game Set

ex) TV Model

EXTERNAL EQUIPMENT SETUP

When connecting HDMI to DVI cable

Connect the PC audio output to the DDVVII//PPCC AAUUDDIIOO

IINN jack on the set.

Connect the DVI output of the PC to the HHDDMMII//DDVVII

IINN jack on the set.

1. How to connect

2. How to use

■

Turn on the PC and the TV.

■

Select HHDDMMII input source by using the TTVV// AAVV button on

the remote control.

When connecting D-sub 15pin cable

Connect the PC audio output to the DDVVII//PPCC AAUUDDIIOO

IINN jack on the set.

Connect the RGB output of the PC to the PPCC IINN jack

on the set.

1. How to connect

2. How to use

■

Turn on the PC and the TV.

■

Select PPCC input source by using the TT VV // AAVV button on the

remote control.

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

PC SETUP

EXTERNAL EQUIPMENT SETUP

To get the the best picture quality, adjust the PC

graphics card to 1024x768, 60Hz.

Depending on the graphics card, DOS mode may

not work if a HDMI to DVI Cable is in use.

Check the image on your TV. There may be noise

associated with the resolution, vertical pattern,

contrast or brightness in PC mode. If noise is

present, change the PC output to another

resolution, change the refresh rate to another rate

or adjust the brightness and contrast on the

VIDEO menu until the picture is clear. If the

refresh rate of the PC graphic card can not be

changed, change the PC graphic card or consult

the manufacturer of the PC graphic card.

Avoid keeping a fixed image on the screen for a

long period of time. The fixed image may become

permanently imprinted on the screen.

The synchronization input form for Horizontal and

Vertical frequencies is separate.

RGB-PC, HDMI1/DVI-PC mode

Horizontal Vertical

Frequency

(

KHz

)

Frequency

(

)

31.469 70.08

31.469 59.94

37.879 60.31

48.363 60.00

47.776 59.87

47.720 59.799

47.130 59.65

Resolution

720x400

136 0x768

640x350

* RGB-PC mode only: 640x350, 720X400

640x480

800x600

102 4x768

HDMI1/DVI-DTV,

HDMI2-DTV mode

Horizontal Vertical

Frequency

(

KHz

)

Frequency

(

)

31.469 59.94

31.500 60.00

44.960 59.94

45.000 60.00

33.720 59.94

33.750 60.00

Resolution

720x480

128 0x720

19 20x1080i

128 0x768

136 6x768

Supported Display Specifications

NOTE

Page is loading ...

LG 26LH1DC3 User manual

Brand: LG

Model: 26LH1DC3

Category: LCD TVs

Type: User manual

This manual is also suitable for

Download PDF

report

LG 26LH1DC3 User manual

This manual is also suitable for

LG 26LH1DC3 User manual

Related papers

Other documents