2. Hitachi
  3. C7SS
C7SS

Hitachi C7SS, C 6SS, C 7SS, Saw C 6SS User manual

  • Hello! I am an AI chatbot trained to assist you with the Hitachi C7SS User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
[ SAME FEATURES AS THE CONVENTIONAL MODELS ]
Accurate and sturdy aluminum die-cast base
(Steel plate base available depending on
destination)
Double-insulated construction
[ NEW FEATURES ]
Compact and lightweight design
Power-plus heavy-duty motor
Sawdust rear-discharge type
(Dust collector installable)
Blower function
Although our C 6MFA/C 7MFA Circular Saws now available on the European market are highly evaluated as
reasonably priced, light-load products, there is also growing demand for less expensive and lighter circular saw
products. In order to expand the market share of our circular saw series products, we consequently released the
C 6SS/C 7SS Circular Saws in wider regions including Europe, as a low-priced series developed by balancing
price and performance.
LIST No.
C 6SS: E519
C 7SS: E520
Jun. 2009
PRODUCT NAME
Hitachi Circular Saw
Models 165 mm (6-1/2”) C 6SS
190 mm (7-1/2”) C 7SS
• Cutting of various wood materials
MARKETING OBJECTIVE
APPLICATIONS
SELLING POINTS
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.
C
Sales Division
REMARK:
• For more information about HANDLING INSTRUCTIONS, visit our website at:
http://www.hitachi-koki.com/manual_view_export/
• Throughout this TECHNICAL DATA AND SERVICE MANUAL, a symbol (s) is (are) used in the place of
company name (s) and model name (s) of our competitor (s). The symbol (s) utilized here is (are) as
follows:
Competitors
Symbols Utilized
Company Name Model Name
D1 MAKTEC MT560
D2 MAKTEC MT580
CONTENTS
Page
SELLING POINTS ------------------------------------------------------------------------------------------------------------- 1
SPECIFICATIONS ------------------------------------------------------------------------------------------------------------- 2
1. Specifications ----------------------------------------------------------------------------------------------------- 2
COMPARISONS WITH SIMILARPRODUCTS -------------------------------------------------------------------------- 3
1. Comparison of Specifications --------------------------------------------------------------------------------3
PRECAUTIONS ON SALES PROMOTION ----------------------------------------------------------------------------- 5
1. Safety Instructions ---------------------------------------------------------------------------------------------- 5
REPAIR GUIDE ----------------------------------------------------------------------------------------------------------------- 6
1. Precautions on Disassembly and Reassembly ---------------------------------------------------------- 6
STANDARD REPAIR TIME (UNIT) SCHEDULES ------------------------------------------------------------------- 13
Assembly Diagram for C 6SS
Assembly Diagram for C 7SS
-1-
Compact and lightweight design
The Models C 6SS and C 7SS adopt the highly evaluated
compact design of the C 6MFA/C 7MFA, and incorporate a
light-weight, highly rigid lower guard and a side handle
made of resin to reduce overall weight.
Power-plus heavy-duty motor
The cooling flow path is enhanced to increase power.
(For 230/240 V)
Sawdust rear-discharge type
(Dust collector installable)
A sawdust rear-discharge method is adopted to prevent
sawdust from accumulating on the work face. Simply
attaching an optional dust collector will ensure a clean
environment with minimal scattering of sawdust.
Blower function
The Models C 6SS and C 7SS come with the blower function to blow sawdust away using cooling air of the
motor.
Accurate and sturdy aluminum die-cast base
(Steel plate base available depending on destination)
Thanks to the sturdy aluminum die-cast base, the Models C 6SS and C 7SS can cut workpieces accurately,
resulting in smooth cut workpiece surfaces.
Double-insulated construction
Grounding is not required due to the double-insulated construction.
Refer to the Technical Data and Service Manuals for current models.
Refer to the Technical Data and Service Manuals for current Models C 6MFA and C 7MFA.
Dust collector
SELLING POINTS
Plastic side handle
Plastic lower guard
C 6SS / C 7SS : 1,050W
C 6MFA / C 7MFA : 1,010W
C 6MFA / List No. E502 C 7MFA / List No. E503
C 6SF / List No. 0597 C 7SF / List No. 0598
C 6MF / List No. 0599 C 7MF / List No. E501
-2-
1. Specifications
Model C 6SS C 7SS
Saw blade diameter 165 mm (6-1/2") 190 mm (7-1/2")
at 90° 0 to 57 mm (0 to 2-1/4") 0 to 68 mm (0 to 2-11/16")
Cutting depth
at 45° Max. 38 mm (1-1/2") Max. 46 mm (1-13/16")
Power source AC single phase 50/60 Hz
Type of motor AC single phase commutator motor
Type of switch Trigger switch
Housing
Handle cover
Lower guard
Polycarbonate resin
Gear cover Cast aluminum
Enclosure
Base Cast aluminum / Sheet steel
*
1
Voltage (V) 110 120 220 230 240
*
1
Current (A) 9.6 9.2 5.0 4.8 4.6
Power input 1,010W 1,050W
No-load Rotation speed 5,600/min. 5,900/min. 5,950/min. 5,650/min.
Aluminum
base
3.2 kg (7.1 lbs.) 3.4 kg (7.5 lbs.)
*
2
Net
Steel base 3.1 kg (6.8 lbs.) 3.3 kg (7.3 lbs.)
Aluminum
base
4.0 kg (8.8 lbs.) 4.3 kg (9.5 lbs.)
Weight
Gross
Steel base 3.9 kg (8.6 lbs.) 4.2 kg (9.3 lbs.)
Packaging Corrugated cardboard box / Plastic case and corrugated cardboard sleeve
Type Two-core cabtire cable
Cord
Overall length 2 m (6.6 ft.)
Standard equipment
Tungsten carbide tipped (TCT) saw blade ------------------------------------- 1
Parallel guide -------------------------------------------------------------------------- 1
Hex. bar wrench ---------------------------------------------------------------------- 1
Case (GBR only) ----------------------------------------------------------------------1
*
1
Check the tool name plate to confirm the rating, as it is subjected to change by area.
*
2
The net weight does not include the cord and the saw blade.
SPECIFICATIONS
-3-
L
W
H
1. Comparison of Specifications
(1) 165mm (6") dia. saw blade (Superior specifications: )
Maker HITACHI
Model C 6SS C 6MFA C 6SF C 6MF
D1
Saw blade diameter mm 165 (6-1/2") 165 (6-1/2")
90㩩
mm 57 (2-1/4") 56 (2-7/32")
Max.cutting
depth
45㩩
mm 38 (1-1/2") 37 (1-15/32")
Power input W *
1
1,050 1,010 1,050
No-load rotation speed /min. 5,500 5,000 4,700
Overall length mm 276 (10-7/8") 270 (10-5/8") 282 (11-3/32") 273 (10-3/4")
Catalog
Weight kg *
2
3.2 (7.0 lbs.) 3.4 (7.5 lbs.) 3.0 (6.6 lbs.) 3.4 (7.5 lbs.)
Motor size mm ĭ72 x 40 ĭ72 x 45
No-load noise dB 85 84
Parallel adjustment --- None Provided None
Installation of dust collector --- Provided None None
Riving knife --- None None
Soft touch handle --- None None
Method of fixing gradient
angle
--- Wing bolt Wing bolt
Method of fixing cut depth --- Lever Wing bolt Wing bolt
Housing --- Resin Resin
Handle cover --- Resin Resin
Gear cover --- Aluminum Aluminum
Lower guard --- Resin Aluminum Resin Resin
Lower guard lever --- Resin Steel Resin Resin
Angle lever / wing bolt --- Resin Resin
Cutting depth lever /
wing bolt
--- Resin Resin
Material
Base ---
Aluminum
or Steel
Aluminum Steel Aluminum Steel
Length (L) mm 276 (10-7/8") 270 (10-5/8") 282 (11-3/32") 273 (10-3/4")
Height (H) mm 230 (9-1/16") 229 (9-1/64") 230 (9-1/16")
Width (W) mm 210 (8-1/4") 231 (9-3/32")
With side handle kg 3.2 (7.0 lbs.) 3.4 (7.5 lbs.) --- --- ---
Weight
Without side handle kg 3.1 (6.8 lbs.) --- 3.0 (6.6 lbs.) 3.4 (7.5 lbs.)
* This rating is based on the 230 V motor.
*
1
110 V specification = 1,010 W
*
2
Mass of aluminum base specification [ Steel base spec: 3.1 kg (6.8 lbs.) ]
COMPARISONS WITH SIMILAR PRODUCTS
-4-
L
W
H
(2) 190mm (7-1/2") dia. saw blade (Superior specifications: )
Maker HITACHI
Model C 7SS C 7MFA C 7SF C 7MF
D2
Saw blade diameter mm 190 (7-1/2") 185 (7-1/4")
90㩩
mm 68 (2-11/16") 66 (2-19/32")
Max.cutting
depth
45㩩
mm 46 (1-13/16") 44 (1-3/4")
Power input W *
1
1,050 1,010 1,050 1,050
No-load rotation speed /min. 5,500 5,000 4,700
Overall length mm
291
(
11-15/32"
)
282
(
11-3/32"
)
295
(
11-19/32"
)
286
(
11-1/4"
)
Catalog
Weight kg *
2
3.4 (7.5 lbs.) 3.6 (7.9 lbs.) 3.3 (7.3 lbs.) 3.5 (7.7 lbs.)
Motor size mm ĭ72 x 40 ĭ72 x 45
No-load noise dB 85 84.5
Parallel adjustment --- None Provided None
Installation of dust collector --- Provided None None
Riving knife --- None None
Soft touch handle --- None None
Method of fixing gradient
angle
--- Wing bolt Wing bolt
Method of fixing cut depth --- Lever Wing bolt Wing bolt
Housing --- Resin Resin
Handle cover --- Resin Resin
Gear cover --- Aluminum Aluminum
Lower guard --- Resin Aluminum Resin Resin
Lower guard lever --- Resin Steel Resin Resin
Angle lever / wing bolt --- Resin Resin
Cutting depth lever /
wing bolt
--- Resin Resin
Material
Base ---
Aluminum
or Steel
Aluminum Steel Aluminum Steel
Length (L) mm
291
(
11-15/32"
)
282
(
11-3/32"
)
295
(
11-19/32"
)
286
(
11-1/4"
)
Height (H) mm
242
(
9-17/32"
)
245
(
9-21/32"
Width (W) mm
210
(
8-1/4"
)
231
(
9-3/32"
)
With side handle kg 3.4 (7.5 lbs.) 3.6 (7.9 lbs.) --- --- ---
Weight
Without side handle kg 3.3 (7.3 lbs.) --- 3.3 (7.3 lbs.) 3.5 (7.7 lbs.)
* This rating is based on the 230 V motor.
*
1
110 V specification = 1,010 W
*
2
Mass of aluminum base specification [ Steel base spec: 3.3 kg (7.3 lbs.) ]
-5-
1. Safety Instructions
In the interest of promoting the safest and most efficient use of the C 6SS and C 7SS Circular Saws by all
of our customers, it is very important when concluding a sale that the salesperson carefully ensure that the
buyer seriously recognizes the importance of the Instruction Manual, and fully understands the precautions
listed on the Warning Labels, Warning Signs and Caution Labels attached to each tool.
A. Instruction manual
Although every effort is made in each step of design, manufacture, and inspection to provide protection
against safety hazards, the dangers inherent in the use of any electric power tool cannot be completely
eliminated. Accordingly, the Instruction Manual lists general precautions and suggestions on the use of
electric power tools, and specific precautions and suggestions on the use of the circular saw in order to
enhance the safe, efficient use of the tool by the customer. Salespersons must be thoroughly familiar
with the contents of the Instruction Manual in order to offer appropriate guidance to customers during
sales promotion activities.
B. Warning labels and caution labels
(1) Precautions on the name plate
The Models C 6SS and C 7SS are both furnished with a Name Plate listing the following precautions
[ For the Europe ]
[ For Australia and New Zealand ]
[ For China ]
[ For Taiwan ]
[ For Latin America ]
PRECAUTIONS ON SALES PROMOTION
-6-
Before disassembly, be sure to remove the saw blade to prevent damage to the cutting edge or personal
injury due to the saw blade.
1. Precautions on Disassembly and Reassembly
The disassembly and reassembly procedures are described below, as well as certain precautions. The
numbers in the descriptions below correspond to item numbers in the Parts List for all the models. In
disassembly, reassembly or other work, the Base [68] should be carefully handled to prevent any loss of
accuracy for each part, such as flatness of the bottom surface.
1. Removal of the Protective Cover
(a) Detach the hook of the Return Spring [6] from the Protective Cover [5].
(b) Loosen the Seal Lock Flat Hd. Screw M3 x 12 [9] that secures the Bearing Cover [8] in place, and then
remove the Bearing Cover [8] and Protective Cover [5].
2. Removal of the Bearing Holder
Loosen the Seal Lock Flat Hd. Screws M5 x 12 [4], and then remove the Bearing Holder [3] together with
the Spindle and Gear Set [2].
3. Removal of the Spindle and Gear Set
Secure the Bearing Holder [3] in a cylindrical jig having
an inner diameter of 42 to 43 mm (about 1-23/32"),
and then push the top end of the Spindle and Gear
Set [2] to remove it.
NOTE:
Once removed, a gear can no longer be used due
to lack of engagement. It must be replaced by a
new Spindle and Gear Set [2].
4. Removal of the Housing Ass’y
(a) Use a flat-blade screwdriver to loosen the Brush Caps [34] and then remove the Carbon Brushes [33].
(b) Loosen the Machine Screws (W/Washers) M5 x 45 (Black) [15] that secure the Housing Ass'y [30] in
place, and then remove the Housing Ass'y [30] and Gear Cover Ass'y [26].
Disassembly
Fig. 1
REPAIR GUIDE
Bearing Holder [3]
Spindle and Gear Set [2]
-7-
5. Removal of the Armature
(a) Remove the Lock Lever [43] and tap the end surface of the Housing Ass'y [30] with a wooden hammer.
The Armature [23] and the Fan Guide [22] can then be removed.
(b) Remove the Fan Guide [22], Thrust Washer [19] and Bearing Lock [18].
(c) Use a bearing puller to remove the Ball Bearing 6000VVCMPS2L [44] and Ball Bearing 608VVC2PS2L
[20], and then remove Washer (A) [21].
6. Removal of the Stator Ass’y
(a) Loosen the two Hex. Hd. Tapping Screws D5 x 55 [42].
(b) Remove the two Brush Terminals [39] from the brush holders of the Housing Ass'y [30].
(c) Lightly tap the end surface of the Housing Ass'y [30] with a wooden hammer to remove the Stator Ass'y
[38].
Fig. 2
Fig. 3
Housing Ass'y [30]
Hex. Hd. Tapping Screw D5 x 55 [42]
Brush Terminals [39]
Stator Ass'y [38]
Ball Bearing 6000VVCMPS2L [44]
A
rmature [23]
Washer (A) [21]
Lock Lever [43]
Ball Bearing 608VVC2PS2L [20]
Thrust Washer [19]
Bearing Lock [18]
Fan Guide [22]
-8-
Fig. 4
7. Removal of the Base
(a) Align the bevel plate hole of Base [68] with the Gear Cover Ass’y [26] and then press-fit Roll Pin D6 x
50 [58].
(b) Loosen the Seal Lock Screw (W/Sp. Washers) M6 x 14 [62], and then remove Lever (A) [63], the Lock
Nut [65], Washer (C) [67] and Bolt (Square) M6 x 20 [28].
Bolt (Square) M6 x 20 [28]
Roll Pin D6 x 50 [58]
Base [68]
Seal Lock Screw (W/Sp.
Washers) M6 x 14 [62]
Lock Nut [65]
Washer (C) [67]
Slotted Hd. Set Screw
(Seal Lock) M6 x 8 [61]
Gear Cover Ass’y [26]
Lever (A) [63]
-9-
Fig. 5
Fig. 6
Perform reassembly by reversing the order of the disassembly procedure. However, special attention
should be given to the following items.
1. Reassembly of the Bearing Lock and Thrust Washer
Before installing the Armature [23], be sure to install the Bearing Lock [18] and Thrust Washer [19] in the
bearing chamber of the Housing Ass'y [30] in this order. When installing the Thrust Washer [19], be sure to
note its direction of assembly.
2. Replacement of the Ball Bearing 608VVC2PS2L
When only replacing the Ball Bearing 608VVC2PS2L [20], make sure that Washer (A) [21] is reassembled
in the proper direction with clearance between the Ball Bearing 608VVC2PS2L [20] and Washer (A) [21].
3. Reassembly of the Rubber Ring
When installing the Rubber Ring [45], be careful not to damage the bearing chamber groove of the Gear
Cover Ass'y [26].
Reassembly
Washer (A) [21]
Ball Bearing 608VVC2PS2L [20]
Housing Ass'y [30]
Bearing Lock [18]
Thrust Washer [19]
-10-
Fig. 7
Fig. 8
4. Reassembly of the Stator Ass’y
As shown in Fig. 7 below, insert a guide bar [J-132 stator press pins (special repair tool, Code No. 970911)
are recommended] into the Stator Ass'y [38] and Housing Ass'y [30] to accurately align the screw hole on
the Stator Ass'y [38] with the corresponding hole on the Housing Ass'y [30]. Press-fit the Stator Ass'y [38]
into the Housing Ass'y [30]. Hook the carbon brush terminals in the brush holders. Be careful not to put
internal wires into the ribs of the Stator Ass'y [38] in the Housing Ass'y [30]. Secure the Stator Ass'y [38] to
the Housing Ass'y [30] with the two Hex. Hd. Tapping Screws D5 x 55 [42].
5. Reassembly of the Lock Lever
(a) Place the notch of the Lock Lever [43] between the fan of the Armature [23] and the ball bearing, and
then assemble both parts into the Gear Cover Ass'y [26]. At this time, both ends of the plate spring of
the Lock Lever [43] should be supported by the inner sides of the ribs (at two places) on the Gear Cover
Ass'y [26].
(b) After installation, check Lock Lever [43] operation to ensure that the lever springs back to its original
position when you release it.
Name plate side
Stator Ass'y [38]
Housing Ass'y [30]
Lock Leve
r
[
43
]
Gear Cover Ass'y [26]
Armature [23]
Brush holder
Guide bar
(J-132 stator
press pins)
-11-
Blue (Lead wire
from stator to
switch)
Fig. 9
Fig. 10
Fig. 11
6. Wiring procedure
Wiring should be done by referring to Figs. 9 and 10 below. During installation, be careful not to pinch the.
lead wires between the housing and handle cover. (Left: with condenser Right: None)
7. Wiring diagram
(Left: with condenser Right: None)
Blue (Lead wire to
switch
)
Brown or Black
(Lead wire from
cord
)
Blue (Lead wire
from stator)
Brown or Black
(Lead wire from
cord
)
Blue or White
(Lead wire from
cord
)
Blue (Lead wire from stator)
-12-
Models Measuring points Allowable level
C 6SS, C 7SS 150 0.3 mm max.
8. Tightening torque values for selected fasteners
• Bolt (W/Washer) M7 x 17.5 [14] ------------------------------------- 9.8 r 2.0 N•m (100 r 20 kgf•cm)
• Seal Lock Screw (W/Sp. Washers) M6 x 14 [62] --------------- 2.9 r 0.5 N•m (30 r 5 kgf•cm)
• Seal Lock Flat Hd. Screw M5 x 12 [4] ----------------------------- 3.4 r 0.7 N•m (35 r 7 kgf•cm)
• Seal Lock Flat Hd. Screw M3 x 12 [9] ----------------------------- 1.8 r 0.4 N•m (18 r 4 kgf•cm)
• Machine Screw (W/Washers) M5 x 45 [15] ---------------------- 3.4 r 0.7 N•m (35 r 7 kgf•cm)
• Screw (W/Washers) M5 x 16 [24] ---------------------------------- 3.4 r 0.7 N•m (35 r 7 kgf•cm)
• Hex. Hd. Tapping Screw D5 x 55 [42] ----------------------------- 2.9 r 0.5 N•m (30 r 5 kgf•cm)
• Tapping Screw (W/Flange) D4 [16], [41] -------------------------- 2.0 r 0.5 N•m (20 r 5 kgf•cm)
• Brush Cap [34] ---------------------------------------------------------- 0.7 r 0.2 N•m (7.5 r 2.5 kgf•cm)
• Hex. Socket Set Screw M5 x 8 [29] -------------------------------- 0.7 r 0.2 N•m (7.5 r 2.5 kgf•cm)
• Flat Hd. Screw M6 x 20 [47] ----------------------------------------- 0.7 r 0.2 N•m (7.5 r 2.5 kgf•cm)
Upon the completion of disassembly and repair, measure the insulation resistance and conduct a dielectric
strength test.
Insulation resistance: 7M or more using a DC 500 V megohm tester
Dielectric strength: AC 4000 V/1 minute, with no abnormalities
The allowable deflection level of the saw blade shall be as follows:
When the unit becomes soiled, use a clean, soft rag moistened with soapy water to clean it. Never use
chloric solvents, gasoline or thinner (which tend to damage plastic material) for cleaning.
Deflection of saw blade
Cleaning the case
Insulation Tests
-13-
MODEL
Variable
Fixed
10 20 30 40 50 60 min.
Work Flow
C 6SS
C 7SS
General Assembly
Handle
Cover
Protective
Cover
Return Spring
Base Ass’y
Switch
Code
Code Armor
Armature
Ball Bearing
(608VV)
Ball Bearing
(6000VV)
Spindle and
Gear Set
Bearing
Holder
Metal
Ball Bearing
(6002VV)
Gear Cover
Ass’y
Housing Ass’y
Stator Ass’y
STANDARD REPAIR TIME (UNIT) SCHEDULES
A
A
Rev.1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
40
41
38
39
42
43
44
45
46
47
29
30
31
32
33
34
36
37
35
51
52
53
56
57
58
59
60
18
61
62
65
67
68
28
501
C6SS
TU01694
33.3%
55
54
50
49
66
64
48
502
63
Model C 6SS
CIRCULAR SAW
LIST NO. E519
(E1)
2009㨯6㨯18
PART
S
C 6SS
DESCRIPTION REMARKS
1 963-803 METAL 1
* 2 322-088 SPINDLE AND GEAR SET 1
* 2 331-705 SPINDLE AND GEAR SET 1 FOR CHI, PAN, MEX
3 308-361 BEARING HOLDER 1
4 305-568 SEAL LOCK FLAT HD. SCREW M5 X 12 2
5 331-266 PROTECTIVE COVER 1
6 331-268 RETURN SPRING 1
7 600-2VV BALL BEARING 6002VVCMPS2L 1
8 308-362 BEARING COVER 1
9 308-773 SEAL LOCK FLAT HD. SCREW M3 X 12 3
* 10 323-928 WASHER (A) 1
* 10 322-099 WASHER (A) 1
FOR NZL, AUS, VEN, THA, INA, SIN, KUW, IND
* 10 317-466 WASHER (A1) 1 FOR CHI, PAN, MEX
* 11 324-678 TCT SAW BLADE 165MM-D30 HOLE-NT16 1
* 11 330-889 TCT SAW BLADE 165MM-D20 HOLE-NT16 1
FOR NZL, AUS, VEN, THA, INA, SIN, KUW, IND
* 11 331-658 TCT SAW BLADE 165MM-D15.9 HOLE-NT16 1 FOR CHI, PAN, MEX
* 12 990-100 RING D15.9/I.D14.5 1 FOR CHI, PAN, MEX
* 13 323-924 WASHER (B) 1
* 13 324-563 WASHER (B2) 1 FOR CHI, PAN, MEX
14 325-541
HEX. SOCKET HD. BOLT (W/WASHER) M7 X 17.5 1
15 302-434
MACHINE SCREW (W/WASHERS) M5 X 45 (BLACK) 3
16 328-643
TAPPING SCREW (W/FLANGE) D4 X 23 (BLACK) 3
17 NAME PLATE 1
18 931-701 BEARING LOCK 2
19 331-264 THRUST WASHER 1
20 608-VVM BALL BEARING 608VVC2PS2L 1
21 982-631 WASHER (A) 1
22 322-002 FAN GUIDE 1
* 23 360-883C ARMATURE 110V 1
* 23 360-883D ARMATURE 120V 1
* 23 360-883E ARMATURE 220V-230V 1
* 23 360-883F ARMATURE 240V 1
* 24 887-021 SCREW (W/WHSHERS) M5 X 16 (BLACK) 3
EXCEPT FOR VEN, THA, INA, SIN, KUW, IND
* 25 330-973 SIDE HANDLE 1 EXCEPT FOR VEN, THA, INA, SIN, KUW, IND
26 331-265 GEAR COVER ASS'Y 1 INCLUD. 45-47
27 HITACHI LABEL 1
28 942-808 BOLT (SQUARE) M6 X 20 1
29 938-477 HEX. SOCKET SET SCREW M5 X 8 2
30 331-260 HOUSING ASS'Y 1 INCLUD. 29, 32
* 31 500-409Z CORD 1 (CORD ARMOR D8.8)
* 31 500-435Z CORD 1
(CORD ARMOR D8.8) FOR GBR (230V), KUW
* 31 500-461Z CORD 1 (CORD ARMOR D8.8) FOR GBR (110V)
* 31 500-247Z CORD 1 (CORD ARMOR D8.8) FOR FIN, NOR, SWE, DEN
* 31 500-447Z CORD 1 (CORD ARMOR D8.8) FOR SUI, CHI
* 31 500-439Z CORD 1 (CORD ARMOR D8.8) FOR NZL, AUS
* 31 500-455Z CORD 1 (CORD ARMOR D8.8) FOR VEN
* 31 500-468Z CORD 1 (CORD ARMOR D8.8) FOR THA
* 31 500-231Z CORD 1 (CIRD ARMOR D8.8) FOR SIN
* 31 500-240Z CORD 1
(CORD ARMOR D8.8) FOR MEX, PAN (120V)
32 957-051 BRUSH HOLDER 2
- 2 - 06 - 09
*ALTERNATIVE PARTS
ITEM
NO.
NO.
USED
CODE NO.
PART
S
C 6SS
DESCRIPTION REMARKS
33 999-043 CARBON BRUSH (1 PAIR) 2
34 935-829 BRUSH CAP 2
* 35 959-140 CONNECTOR 50091 (10 PCS.) 1
FOR VEN, THA, INA, IND, PAN, SIN, KUW, MEX, CHI
36 953-327 CORD ARMOR D8.8 1
37 331-707 FASTON 1
* 38 340-614C STATOR ASS'Y 110V 1 INCLUD. 39
* 38 340-756C STATOR ASS'Y 110V 1 INCLUD. 39 FOR VEN
* 38 340-756D STATOR ASS'Y 120V 1 INCLUD. 39
* 38 340-614E STATOR ASS'Y 230V 1 INCLUD. 39
* 38 340-756E STATOR ASS'Y 220V-230V 1
INCLUD. 39 FOR THA, INA, SIN, CHI, PAN, IND
* 38 340-614F STATOR ASS'Y 240V 1 INCLUD. 39
* 38 340-756F STATOR ASS'Y 240V 1 INCLUD. 39 FOR KUW
39 930-703 BRUSH TERMINAL 2
40 937-631 CORD CLIP 1
41 984-750 TAPPING SCREW (W/FLANGE) D4 X 16 2
42 953-174 HEX. HD. TAPPING SCREW D5 X 55 2
43 307-918 LOCK LEVER 1
44 600-0VV BALL BEARING 6000VVCMPS2L 1
45 318-647 RUBBER RING 1
46 961-729 CUSHION 1
47 949-794 FLAT HD. SCREW M6 X 20 (10 PCS.) 1
48 331-706 WASHER 1
49 949-454 SPRING WASHER M5 (10 PCS.) 1
50 949-237 MACHINE SCREW M5 X 12 (10 PCS.) 1
* 51 331-269 INTERNAL WIRE 1 EXCEPT FOR VEN, PAN, CHI, THA,
INA, SIN, KUW, MEX, IND
52 331-259 SWITCH 1
53 331-261 HANDLE COVER 1
54 307-898 WING BOLT M6 X 18 1
55 941-056 SPRING 1
* 56 307-937 WING BOLT (A) 1
* 56 308-364 WING BOLT (A) M6 X 15 1
FOR VEN, THA, INA, SIN, KUW, CHI, PAN, MEX, IND
57 948-167 SUPER LOCK WASHER M6 1
58 949-750 ROLL PIN D6 X 50 (10 PCS.) 1
* 59 930-039 NOISE SUPPRESSOR 1 FOR GBR, SAF, EUROPE, AUT, FIN,
NOR, SWE, DEN, SUI, NZL, AUS
* 60 959-141 CONNECTOR 50092 (10 PCS.) 2 FOR NOISE SUPPRESSOR
* 61 308-109
SLOTTED HD. SET SCREW (SEAL LOCK) M6 X 8 1 EXCEPT FOR VEN, THA, INA, SIN,
KUW, CHI, PAN, MEX, IND
62 322-260
SEAL LOCK SCREW (W/SP. WASHERS) M6 X 14 1
63 323-923 LEVER (A) 1
64 949-566 LOCK NUT M5 (10 PCS.) 1
65 328-048 LOCK NUT 1
66 331-708 PLATE 1
67 329-933 WASHER (C) 1
* 68 331-262 BASE 1 INCLUD. 54-57, 61
* 68 331-263 BASE 1 INCLUD. 54-57 FOR VEN, THA, INA,
SIN, KUW, CHI, PAN, MEX, IND
06 - 09 - 3 -
*ALTERNATIVE PARTS
NO.
USED
CODE NO.
ITEM
NO.
C 6SS
DESCRIPTION REMARKS
501 944-459 HEX. BAR WRENCH 5MM 1
502 302-756 GUIDE 1
DESCRIPTION REMARKS
601 302-981 DUST COLLECTOR SET (D) 1
602 322-099 WASHER (A) 1
- 4 - Printed in Japan 06 - 09
(090618N)
*ALTERNATIVE PARTS
NO.
USED
CODE NO.
ITEM
NO.
NO.
USED
CODE NO.
ITEM
NO.
STANDARD ACCESSORIES
OPTIONAL ACCESSORIES
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/