KitchenAid KOASP 60602 User guide

Brand: KitchenAid

Model: KOASP 60602

Category: Kitchen & houseware accessories

Type: User guide

This manual is also suitable for

Instructions for use

IMPORTANT SAFETY INSTRUCTIONS 4

Installation 8

Safeguarding the environment 9

ECO Design Declaration 9

Troubleshooting guide 10

After-Sales Service 10

Cleaning 10

Maintenance 12

Instruction for oven use 13

Functions description table 32

Artisan steam function cooking table 35

Cooking table 36

Table of tested recipes 40

Recommended use and tips 41

These instructions are also available on the website: www.kitchenaid.eu

IMPORTANT SAFETY INSTRUCTIONS

SAFETY IS OUR PRIORITY

This manual and the appliance itself display important safety warnings, to be

read and observed at all times.

This is the danger symbol relating to safety, which alerts users to

potential risks to themselves and others. All safety warnings are

preceded by the danger symbol and the text shown here:

Indicates a hazardous situation which,

if not avoided, will cause serious injury.

Indicates a hazardous situation which,

if not avoided, could cause serious injury.

All safety warnings give specic details of the

potential risk present, and indicate how to reduce

the risk of injury, damage and electric shock

resulting from improper use of the appliance.

Carefully observe the following instructions:

• Use protective gloves to perform all unpacking

and installation operations.

• The appliance must remain disconnected from

the power supply before any installation work is

carried out.

• Installation and maintenance must be carried

out by a qualied technician, in compliance with

the manufacturer’s instructions and local safety

regulations. Do not repair or replace any part of

the appliance unless specically stated in the user

manual.

• Replacement of power cables must be carried out

by a qualied electrician. Contact an authorised

After-Sales Service.

• Regulations require that the appliance be earthed.

• Once the appliance is tted in its housing, the

DANGER

WARNING

power cable must be long enough to connect the

appliance to the main power supply.

• For installation to comply with current safety

regulations, an omnipolar disconnect switch with

minimum contact gap of 3 mm must be used.

• Do not use multiple plug adaptors if the oven is

tted with a plug.

• Do not use extension leads.

• Do not pull the power supply cable.

• The electrical components must not be accessible

to the user after installation.

• Do not use the surface of the induction plate if it is

cracked, and switch o the appliance to avoid the

possibility of electric shock (only for models with

induction function).

• Do not touch the appliance with any wet part of

the body and do not operate it when barefoot.

• This appliance is designed solely for use as a

domestic appliance, for cooking food. No other

use is permitted (e.g. heating rooms).

The manufacturer declines any liability for

inappropriate use or incorrect setting of the

controls.

• The appliance and its accessible parts become hot

during use.

• Care should be taken to avoid touching heating

elements.

• Very young (0-3 years) and young children (3-8

years) must be kept away unless continuously

supervised.

• Children aged 8 years and above, and persons

with reduced physical, sensory or mental

capabilities or lack of experience and knowledge

can only use this appliance if they are supervised

or have been given instructions on safe appliance

use, and if they understand the hazards involved.

Children must not play with the appliance.

Cleaning and user maintenance must not be

carried out by children without supervision.

• During and after use, do not touch the heating

elements or interior surfaces of the appliance

– risk of burns. Do not allow the appliance to

come into contact with cloths or other ammable

materials until all the components have cooled

down completely.

• At the end of cooking, exercise caution when

opening the appliance door, letting the hot air or

steam exit gradually before accessing the oven.

When the appliance door is shut, hot air is vented

from the aperture above the control panel. Do not

obstruct the vent apertures.

• Use oven gloves to remove pans and accessories,

taking care not to touch the heating elements.

• Do not place ammable materials in or near the

appliance: a re may break out if the appliance is

inadvertently switched on.

• Do not heat or cook sealed jars or containers in

the appliance.

• The pressure that builds up inside might cause the

jar to explode, damaging the appliance.

• Do not use containers made of synthetic

materials.

• Overheated oils and fats catch re easily. Always

remain vigilant when cooking foods rich in fat and

oil.

• Never leave the appliance unattended during

food drying.

• If alcoholic beverages are used when cooking

foods (e.g. rum, cognac, wine), remember that

alcohol evaporates at high temperatures. As a

result, there is a risk that vapours released by the

alcohol may catch re upon coming into contact

with the electrical heating element.

• Never use steam cleaning equipment.

• Do not touch the oven during the pyrolysis

cycle. Keep children away from the oven during

the pyrolysis cycle. Any excess spillage must be

removed from the oven cavity before the cleaning

cycle (only for ovens with pyrolysis function).

• During and after the pyrolysis cycle, animals must

be kept away from the appliance (only for ovens

with pyrolysis function).

• Use only the temperature probe recommended

for this oven.

• Do not use harsh, abrasive cleaners or sharp metal

scrapers to clean the oven door glass as they can

scratch the surface, which may result in the glass

shattering.

• Ensure that the appliance is switched o before

replacing the lamp to avoid the possibility of

electric shock.

• Do not use aluminium foil to cover food in the

cooking vessel (only for ovens with a cooking

vessel supplied).

SCRAPPING OF HOUSEHOLD APPLIANCES

• This appliance is manufactured with recyclable or reusable materials. Scrap

the appliance in accordance with local regulations on waste disposal.

Before scrapping, cut o the power cords so that the appliances cannot be

connected to the mains.

• For further information on the treatment, recovery and recycling of

household appliances, contact the competent local authority, the domestic

waste collection service or the shop where you purchased the product.

After unpacking the oven, ensure that it has not

been damaged during transit and that the oven

door closes properly.

In the event of problems, contact the dealer

or your nearest After-Sales Service. To avoid

any damage, only remove the oven from its

polystyrene foam base at the time of installation.

Preparing the housing unit

• Kitchen units in contact with the oven must be

heat-resistant (min. 90°C).

• Carry out all cabinet cutting work before

tting the oven in the housing and carefully

remove all wood chips and sawdust.

• After installation, the bottom of the oven must

no longer be accessible.

• For correct appliance operation, do not

obstruct the minimum gap between the

worktop and the upper edge of the oven.

Electrical connection

Ensure that the power voltage specied on the

appliance rating plate is the same as the mains

voltage. The rating plate is on the front edge of the

oven (visible when the door is open).

• Power cable replacement (type H05 RR-F 3 x

1.5 mm2) must be carried out by a qualied

electrician. Contact an authorised After-Sales

Service.

The oven is programmed to operate with power

absorption above 2.5 kW (indicated by “HIGH” in

the settings, as shown in the gure below) which

is compatible with a domestic power supply

above 3 kW. If the household has a lower power

supply, the setting must be lowered (“LOW”

in the settings). The table below details the

recommended electrical power settings for the

various countries.

COUNTRY ELECTRICAL POWER

SETTING

GERMANY HIGH

SPAIN LOW

FINLAND HIGH

FRANCE HIGH

ITALY LOW

NETHERLANDS HIGH

NORWAY HIGH

SWEDEN HIGH

U.K. LOW

BELGIUM HIGH

1. To lower the power absorption setting, turn

the “Functions” knob to “SETTINGS” and select.

2. Conrm with button

3. Select “power” on the menu

4. Conrm with button

5. Select “LOW”

6. Press button

; a message appears on the

display conrming your selection.

GENERAL RECOMMENDATIONS

Before use:

• Remove cardboard protection pieces,

protective lm and adhesive labels from the

oven and the accessories.

• Remove the accessories from the oven

and heat it at 200°C for about one hour

to eliminate the smell and fumes from the

protective grease and insulating materials.

During use:

• Do not place heavy objects on the door as

they could damage it.

• Do not cling to the door or hang anything

from the handle.

• Do not cover the inside of the oven with

aluminium foil.

• Do not pour water into the inside of a hot

oven; this could damage the enamel coating.

• Do not drag pots or pans across the bottom

of the oven as this could damage the enamel

coating.

• Ensure that the electrical cables of other

appliances do not touch hot parts of the oven

or become trapped in the door.

• Do not expose the oven to atmospheric

agents.

Settings

Cleaning

Traditional

Appliance and display settings

Power

Language

Time

Appliance and display settings

High

Low

Over 2.5 kW

Installation

Disposal of packing materials

• The packaging materials are 100 % recyclable

and are marked with the recycling symbol

• The various parts of the packing must

therefore be disposed of responsibly and in full

compliance with local authority regulations

governing waste disposal.

Appliance scrapping

• This appliance is marked in compliance with

European Directive 2012/19/EU on Waste

Electrical and Electronic Equipment (WEEE).

• By ensuring correct disposal of the product,

the user can help prevent potential negative

consequences for the environment and

human health.

• The symbol

on the product or on the

accompanying documentation indicates that

it should not be treated as domestic waste but

must be taken to an appropriate collection

centre for the recycling of electrical and

electronic equipment.

Energy saving tips

• Only preheat the oven if specied in the

cooking table or your recipe.

• Use dark lacquered or enamelled baking

moulds as they absorb heat far better.

Safeguarding the environment

ECO Design Declaration

• This appliance meets the eco design requirements of European regulation no. 65/2014 and no.

66/2014 in conformity with European standard EN 60350-1.

Installation

After use:

• Allow the Artisan accessory to cool down

before removal if cleaning is required. When

the Artisan accessory is removed from the

oven, ensure that the cap supplied is used to

prevent dirt entering the electrical socket.

After-Sales Service

Before contacting the After-Sales Service:

• See whether you can solve the problem with

the help of the suggestions given in the

“Troubleshooting guide”.

• Switch the appliance o and then on again

it to see whether the problem has been

eliminated.

If the fault persists after the above checks,

contact the nearest After-Sales Service.

Always specify:

• a brief description of the fault;

• the type and exact model of the oven;

• the service number (number after the word

”Service” on the rating plate), located on the

right hand edge of the oven cavity (visible

when the oven door is open). The service

number is also indicated on the guarantee

booklet;

• your full address;

• your telephone number.

If any repairs are required, contact an authorised

After-Sales Service (to guarantee use of original

spare parts and correct repair).

Cleaning

– Do not use steam cleaners.

– Do not clean the oven until it is cool to the

touch.

– Disconnect the appliance from the mains

power supply.

Oven exterior

IMPORTANT: do not use corrosive or abrasive

detergents. If any of these products comes into

contact with the appliance, clean immediately

with a damp cloth.

• Clean the surfaces with a damp cloth. If it is

very dirty, add a few drops of washing up

detergent to the water. Finish o with a dry

cloth

Oven interior

IMPORTANT: do not use abrasive sponges or

metallic scrapers or scourers. Over time, these

can ruin enamelled surfaces and the oven door

glass.

• Allow the oven to cool after every use, then

clean it preferably while it is still warm in order

to remove built-up dirt and stains caused by

food residues (e.g. food with a high sugar

content).

• Use oven detergents and follow the

manufacturer’s instructions to the letter.

• Clean the door glass with a suitable liquid

detergent. The oven door can be removed to

facilitate cleaning (see MAINTENANCE).

• Do not clean Artisan cavity plug immediately

before running an Artisan cooking cycle.

• Observe the following recommendations

when cleaning the round stainless steel

cover of the fan and Artisan plug plate

(Twelix Disc):

– use a soft cloth (microbre is best)

dampened with water or glass detergent.

– do not use absorbent kitchen paper,

which can leave traces of paper and

streaks on the glass.

Troubleshooting guide

The oven does not work:

• Check the mains electrical power and ascertain whether the oven is connected to the electrical

supply.

• Switch the oven o and then on again to see whether this eliminates the fault.

The electronic programmer does not work:

• If the display shows the letter “ F” followed by a number, contact your nearest After-Sales Service.

Specify in this case the number after the letter “ F”.

Cleaning

N.B: during prolonged cooking of foods with

a high water content (e.g. pizza, vegetables,

etc.) condensation may form on the inside of

the door and around the seal. When the oven is

cold, dry the inside of the door with a cloth or

sponge.

Accessories:

• Soak the accessories in water with washing

up detergent immediately after use, handling

them with oven gloves if still hot.

• Food residues can be easily removed using a

washing-up brush or sponge.

• See “Cleaning” for Artisan accessory cleaning.

Cleaning cycle of ovens with pyrolysis function

(if present):

WARNING

– Do not touch the oven during the pyrolysis

cycle.

– Keep children away from the oven during

the pyrolysis cycle.

– Keep animals away during and after the

pyrolysis cycle.

– Insert the cap of the cavity plug before

running a pyro cycle.

This function burns o spatter occurring inside the

oven during cooking at a temperature of approx.

500°C. At this high temperature, the deposits turn

into a light ash which can be easily wiped away

with a damp cloth, once the oven is cool.

Do not select the pyrolysis function after every

use, only when the oven is very dirty or produces

smoke or fumes while preheating or cooking.

• If the oven is installed below a hob, ensure that

all burners or electric hotplates are switched

o during the self-cleaning (pyrolysis)

function.

• Remove all accessories before running the

pyrolysis function (including the lateral grids).

• For optimum cleaning of the oven door,

remove the worst soiling with a damp sponge

before using the pyrolytic function.

• Before selecting the pyrolysis function, use

a damp sponge to remove any marks on the

round stainless steel cover of the fan (Twelix

Disc) and from the inside glass of the oven

door.

The appliance is equipped with 2 pyrolysis

functions:

1. Energy-saving cycle (PYRO EXPRESS/ECO):

which consumes approximately 25% less

energy than the standard cycle. Select it at

regular intervals (after cooking meat on 2 or 3

consecutive occasions).

2. Standard cycle (PYRO): which is suitable for

cleaning a very dirty oven.

• In any case, after a certain number of uses

and depending on how dirty the oven is, a

message on the oven display advises you to

run a self-cleaning cycle.

N.B: during the pyrolysis function, the oven

door will not open; it will remain locked until

the temperature inside the oven has returned

to an acceptably safe level.

Artisan accessory cleaning:

• Internal electrical socket: remove the metallic

plug cover; use a humidied sponge to clean

the plug. Do not use metallic and/or sharp

tools.

• After every use, allow the steam grid to cool

then clean it, preferably while it is still warm,

in order to remove built-up dirt and stains

caused by food residues (e.g. food with high

sugar content). Suitable for dishwashing.

• Soak the drip pan in water with washing up

detergent immediately after use, handling

them with oven gloves if still hot. Food

residues can be easily removed using the

brush supplied by the After-Sales Service.

Note: after a certain number of uses at high

temperatures, there is a naturally occurring

colour change of the heating element, due to the

formation of layers of ferrous oxide aggregates,

which do not aect the functionality and safety of

the component.

Descaling:

Pour in an additional 800 ml of cold white vinegar

and top up to “Max” with room temperature water.

Leave for 6-8 hours, then rinse with water and

remove any residue with a non-abrasive sponge.

Specic products for cleaning and descaling can

be purchased separately from the After-Sales

Service.

– Use protective gloves.

– Ensure that the oven is cold before carrying out the following

operations.

– Disconnect the appliance from the mains power supply.

WARNING

REMOVING THE DOOR

To remove the door:

1. Open the door fully.

2. Lift the catches and push them forwards as far as they will go (g. 1).

3. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is

released (D) (g. 2).

To ret the door:

1. Insert the hinges in their seats.

2. Open the door fully.

3. Lower the two catches.

4. Close the door.

REMOVING THE SIDE GRILLES

The side accessory-holder grilles are equipped with two xing screws

(g.3) for optimum stability.

1. Remove the screws and relative plates on the right and left with

the aid of a coin or tool (g.4).

2. To remove the grilles, lift them up (1) and turn them (2) as shown

in g.5.

REPLACING THE LAMP

To replace the rear lamp (if present):

1. Disconnect the oven from the mains power supply.

2. Unscrew the lamp cover, replace the lamp (see note for lamp type)

and screw the lamp cover back on.

3. Reconnect the oven to the power supply.

N.B:

– Use only 25-40W/230V type E-14, T300°C incandescent lamps, or

20-40W/230 V type G9, T300°C halogen lamps.

– The lamp used in the appliance is specically designed for

electrical appliances, and is not suitable for household room

illumination (Commission Regulation (ES) no. 244/2009).

– Lamps are available from our After-Sales Service.

IMPORTANT:

– If using halogen lamps, do not handle with bare hands since

ngerprints can damage them.

– Do not use the oven until the lamp cover has been put back in

place.

(Fig.3)

(Fig.4)

(Fig.5)

Fig. 1

Fig. 2

Maintenance

Instruction for oven use

FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION

The Artisan oven is equipped with an electrical socket on the rear wall of the oven to supply power to

the heating element inside the Artisan accessory when plugged in.

1. Control panel

2. Upper heating element/grill

3. Cooling fan (not visible)

4. Rating plate (not to be removed)

5. Lamps

6. Circular heating element (not visible)

7. Fan

8. Rotisserie (if supplied)

9. Bottom heating element (not visible)

10. Door

11. Position of shelves (the number of shelves is indicated on the front of the oven)

12. Rear wall

13. Meat probe connection

14. Twelix disc

15. Modular plug connection

16. Cap (When the Artisan accessory is removed from the oven, ensure that the cap supplied is used to

prevent dirt entering the electrical socket)

17. Glass lid

18. Perforated shelf

19. Drip tray + heating element

20. Drip tray rack

N.B:

– During cooking, the cooling fan may switch on at intervals in order to minimise energy consumption.

– At the end of cooking, after the oven has been switched o, the cooling fan may continue to run for

a while.

– When the oven door is opened during cooking, the heating elements switch o.

Instruction for oven use

ACCESSORIES SUPPLIED

A. WIRE SHELF: the wire shelf can be used to grill food or as a support

for pans, cake tins and other oven-proof cookware.

(Fig.A)

B. BAKING TRAY: for making bread and pastry products, but also

roasts, sh en papillotte, etc.

(Fig.B)

C. MEAT PROBE: for measuring the core temperature of food during

cooking.

(Fig.C)

D. DRYING TRAY: the drying tray is designed for drying fruit,

mushrooms or vegetables.

(Fig.D)

E. TURNSPIT: for uniform roasting of large pieces of meat and poultry.

(Fig.E)

F. SLIDING SHELVES: for easier handling of shelves and trays.

(Fig.F)

Instruction for oven use

G. GLASS LID

(Fig.G)

H. PERFORATED SHELF

(Fig.H)

I. DRIP TRAY + HEATING ELEMENT

(Fig.I)

L. DRIP TRAY RACK

(Fig.L

M. CAVITY PLUG CAP

(Fig.M)

Steam accessory assembled and ready to be plugged in inside the

oven

The number of accessories may vary according to which model is purchased.

ACCESSORIES NOT SUPPLIED

Other accessories can be purchased separately from the After-Sales Service.

Instruction for oven use

INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN

1. Insert the wire shelf horizontally, with the raised part “A” facing upwards (Fig.1).

2. The other accessories, such as the baking tray, are inserted with the same way as the wire shelf

(Fig.2).

Fig.1 Fig.2

Before every steam cooking cycle, check that the male pins are clean in

order to guarantee the right connection.

Place the drip tray (1) on its support (2 – drip tray rack), ensuring that the

plug is positioned on the opposite side of the handle.

Place the perforated shelf (3 – steam grid) on the drip tray (1)

HOW TO ASSEMBLE AN ARTISAN STEAM ACCESSORY

Artisan accessory must be inserted at the rst shelf position to allow the electrical plug to engage.

N.B. sliding shelves cannot be installed at the rst and second shelf position because they will interfere

with the Artisan accessory

1. Use both hands to properly place the Artisan accessory at the rst shelf position (Fig.1)

2. Use the handle to push the Artisan accessory up to the socket. (Fig.2)

3. Ensure that the plug is fully engaged by rmly pushing in the Artisan accessory (Fig. 2)

4. A message conrming correct connection will be shown on the display (g.4A). When the accessory

is unplugged, this will be shown on the display (Fig.4B).

Removing the accessory

IMPORTANT: The Artisan accessory can become extremely hot. Always use oven gloves to touch and

move it.

Grasp the front handle and partially remove the accessory (Fig.2)

Then use lateral support to better grasp and fully remove the accessory, carefully avoiding impacts that

could damage the electrical plug (Fig.3)

Accessory inserted

(Fig.4A)

Accessory removed

(Fig.4B)

(Fig.1) (Fig.1) (Fig.1)

Instruction for oven use

ARTISAN ACCESSORY

Food types/custom steam preparation

Use both hands to properly place the Artisan accessory on the rst shelf position (g.1)

Ensure that the plug is fully engaged by rmly pushing in the Artisan accessory (g.2)

Fill with water (in according to recipe – g.5)

Insert the oven grid at the second/third shelf position (depending on the food), place the casserole with

the food on the oven grid (this is to avoid smoke caused by dripping grease – g.6)

Close the door and press

Important: do not place the food directly on the steam grid or on the oven grid; do not add water

during steam cooking cycle; if the cycle starts without water, stop it and wait about 20-30 minutes

with the oven door fully opened before adding the water.

Pure steam preparation

1. Use both hands to properly place the Artisan accessory on the rst shelf position (g. 1)

2. Ensure that the plug is fully engaged by rmly pushing in the Artisan accessory (g. 2)

3. Fill with water (in according to recipe – g. 5)

4. Place the food on the perforated shelf, ensuring that is correctly positioned inside the pan set tray

(g. 7)

5. Place the glass lid correctly on the drip pan, ensuring that the seals t inside the drip pan itself (g. 8)

6. Close the door and press

Important: do not add water during steam cooking cycle; if the cycle starts without water, stop it

and wait about 20-30 minutes with oven door fully opened before adding the water

(Fig.5) (Fig.6) (Fig.7)

(Fig.8)

Instruction for oven use

1. FUNCTIONS KNOB: On/o and function selector knob

2. BROWSE KNOB: for browsing the menu and adjusting pre-set values

3. BUTTON

: to return to the previous screen

4. BUTTON

: to select and conrm settings

LIST OF FUNCTIONS

Turn the “Functions” knob to any position. The oven switches on. The display will show the following

indication:

Press any key to skip the message and the display will show the

functions or the associated submenus.

Note: The accessory rst alert can be disabled/enabled through

the Settings menu. If the Artisan accessory is already properly

engaged, while oven is switched on, the rst Artisan alert will

not be shown.

The submenus are available and selectable by turning the knob to the functions ARTISAN FUNCTION,

ARTISAN STEAM FUNCTION, GRILL, SPECIALS, SETTINGS and RECIPES.

Always remove the accessory when using

traditional cooking methods. Press any key

CONTROL PANEL DESCRIPTION

DISPLAY

1 3 4 2

Instruction for oven use

Turn the “Functions” knob to any position and the oven switches on: the display shows the functions or

the associated submenus.

A. Symbol for highlighted function

B. Highlighted function can be selected

by pressing

C. Description of highlighted function

D. Other available and selectable functions

FUNCTION DETAILS

After selecting the desired function, the display will show further options and related details.

To move between the dierent zones, use the “Browse” knob: the cursor moves to the adjustable values,

following the order described above.

Press button

to select the value, change it by turning the “Browse” knob and conrm with button

FIRST USE - SELECTING A LANGUAGE AND SETTING THE TIME

For correct use of the oven, you will have to select the desired language and set the correct time when it

is switched on for the rst time.

Proceed as follows

1. Turn the “Functions” knob to any position: the display will show the list of the rst three available

languages.

2. Turn the “Browse” knob to scroll the list.

3. When the desired language is highlighted, press

to select it. After language selection, the display

will ash 12:00.

4. Set the time by turning the “Browse” knob.

5. Conrm your setting by pressing

Traditional

Professional

Special functions

Traditional manual cooking functions

Start

Grill

Medium

GRILL POWER

PREHEAT.

--:--

COOK TIME

--:--

END TIME

Zone 3

Zone 4

Zone 1

Zone 2

Zone 5

CURSOR

Page is loading ...

KitchenAid KOASP 60602 User guide

Brand: KitchenAid

Model: KOASP 60602

Category: Kitchen & houseware accessories

Type: User guide

This manual is also suitable for

Download PDF

report

KitchenAid KOASP 60602 User guide

This manual is also suitable for

KitchenAid KOASP 60602 User guide

Related papers

Other documents