FRIDGE-FREEZER
REFRIGERATEUR-
CONGELATEUR
FRIGORÍFICO-
CONGELADOR
ZFD 19/4
INSTRUCTION BOOKLET MODE D’EMPLOI LIBRO DE INSTRUCCIONES
2222 162-26
2
WARNINGS
General Safety
ª
This appliance is designed to be operated by
adults. Children should not be allowed to tamper
with the controls or play with the product.
ª
It is dangerous to alter the specifications or modify
this product in any way.
ª
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
ª
Before any cleaning or maintenance work is
carried out, be sure to switch off and unplug the
appliance.
ª
This appliance is heavy. Care should be taken
when moving it.
ª
Ice lollies can cause frost burns if consumed
straight from the appliance.
Service / Repair
ª
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
ª
This product should be serviced by an authorized
Service Centre, and only genuine spare parts
should be used.
ª
Under no circumstances should you attempt to
repair the appliance yourself.
Repairs carried out by inexperienced persons may
cause injury or more serious malfunctioning. Refer
to your local Service Centre, and always insist on
genuine spare parts.
Use
ª
The domestic refrigerators and freezers are
designed to be used specifically for the storage of
edible foodstuffs only.
ª
Frozen food must not be re-frozen once it has been
thawed out.
ª
Manufacturers’ storage recommendations should
be strictly adhered to. Refer to relevant
instructions.
ª
The inner lining of the appliance consists of
channels through which the refrigerant passes. If
these should be punctured this would damage the
appliance beyond repair and cause food loss.
DO NOT USE SHARP INSTRUMENTS to scrape
off frost or ice. Frost may be removed by using the
scraper provided. Under no circumstances should
solid ice be forced off the liner. Solid ice should be
allowed to thaw when defrosting the appliance.
See defrost instructions.
ª
Do not place carbonated or fizzy drinks in the
freezer as it creates pressure on the container,
which may cause it to explode, resulting in
damage to the appliance.
Installation
ª
There are working parts in this product which heat
up. Always ensure that there is adequate
ventilation as a failure to do this will result in
component failure and possible food loss. See
installation instructions.
ª
Parts which heat up should not be exposed.
Wherever possible the back of the product should
be against a wall.
ª
If the appliance has been transported horizontally,
it is possible that the oil contained in the
compressor flows in the refrigerant circuit. It is
advisable to wait at least two hours before
connecting the appliance to allow the oil to flow
back in the compressor.
Environment Protection
ª
This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The
appliance shall not be discarded together with
the urban refuse and rubbish. Avoid damaging
the cooling unit, especially at the rear near the
heat exchanger. Information on your local
disposal sites may be obtained from your
municipal authorities.
The materials used on this appliance marked
with the symbol are recyclable.
It is most important that this instruction book should be retained with the appliance for future reference.
Should the appliance be sold or transferred to another owner, or should you move house and leave the
appliance, always ensure that the book is supplied with the appliance in order that the new owner can be
acquainted with the functioning of the appliance and the relevant warnings.
These warnings are provided in the interest of safety. You must read them carefully before installing or
using the appliance.
GB
3
CONTENTS
Installation
4
ª
Caution
4
ª
Location
4
ª
Rear spacers
4
ª
Cleaning the interior
5
ª
Door reversibility
6
ª
Electrical connection
6
Technical specification
6
Operation
7
ª
Starting-up and Temperature Regulation
7
ª
Fresh food refrigeration
7
ª
Movable shelves
8
ª
Positioning the door shelf
8
ª
Freezing fresh food
9
ª
Storage of frozen food
9
ª
Thawing
9
ª
Defrosting
10
ª
Ice-cube production
10
Maintenance
11
ª
Internal cleaning
11
ª
External cleaning
11
ª
Periods of non-operation
11
ª
Interior light
11
Customer service
11
02/98
2222 162-26
GB
4
INSTALLATION
Caution
If this appliance featuring magnetic door seals is to
replace an older appliance having a spring lock (latch)
on the door or lid, be sure to make that spring lock
unusable before you discard the old appliance. This
will prevent it from becoming a death-trap for a child.
Location
The appliance should be installed well away from
sources of heat such as radiators, boilers, direct
sunlight etc.
Best performance is obtained with ambient
temperature between +18
°
C and +43
°
C (class T);
+18
°
C and +38
°
C (class ST); +16
°
C and +32
°
C (class
N); +10
°
C and +32
°
C (class SN).
The class of your appliance is shown on its rating
plate.
Make sure that there is nothing at the back, at the top
and at the bottom of the appliance to obstruct air
circulation.
For a more efficient operation of the appliance, the
minimum distance between the top of the appliance
and other overhanging kitchen furniture, if any,
should be at least 100 mm (see Fig. 1 - A).
However, the best solution would be that shown in
Fig. 1 - B with no overhanging furniture.
Two adjustable feet make it possible to accurately
level the appliance.
Rear spacers
(Fig. 2)
In the plastic envelope containing the Operating
Instructions are also included two wall spacers to be
fitted into the special openings provided on the back
of the appliance.
Push-fit the spacers into the openings, making sure
that arrow (A) is positioned as per Fig. 2 and then turn
the spacers through 45
°
until they lock in (arrow (A)
in a vertical position).
Fig. 1
Fig. 2
NP003
A
B
100 mm 10 mm
10 mm
D039
A
45°
GB
5
Important
It is essential that the appliance be connected to an
efficient earth tap. For this purpose the supply cable
plug incorporates a special earth contact. If the
sockets of your domestic wiring system are not
earthed, have the appliance connected to a separate
earth wire by a qualified electrician in accordance
with existing safety regulations.
The Manufacturer declines all responsibility if the
above safety precautions are not observed.
This appliance complies with EEC directive
number 87/308 of 2/6/87 relative to radio
interference suppression.
This appliance complies with the following
E.E.C. Directives:
-
73/23 EEC
of 19.2.73 (Low Voltage Directive) and
subsequent modifications;
-
89/336 EEC
of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
Cleaning the interior
Before using the appliance for the first time, wash the
interior and all internal accessories with lukewarm
water and some neutral soap so as to remove the
typical smell of a brand-new product, then dry
thoroughly.
Do not use detergents or abrasive powders, as these
will damage the finish.
6
Door reversibility
Before carrying out any work on the appliance,
unplug it from the power socket.
Remove the upper hinge (Fig. 3) and slide the top
door off the middle hinge.
Remove the middle hinge, turn it through 180
°
and
refit it on the opposite side (Fig. 3a) after having
removed the plugs which mask the holes. The plugs
must be refitted in the holes left open on the opposite
side.
Refit the top door and the top hinge. Unscrew the left-
hand levelling foot, which will be refitted on the
opposite side. Unscrew the right-hand levelling foot,
the corresponding hinge and refit all these on the left-
hand side (Fig. 3b).
Reverse the handles after having removed the clip-in
screw covers. The unused holes are masked with
plastic plugs which should be removed and refitted in
the holes left open.
Attention
After completion of the door reversibility operation,
verify that the door gasket is adherent to the cabinet.
If the ambient temperature is cold (i.e. in Winter), the
gasket may not fit perfectly to the cabinet. In that
case, wait for the natural fitting of the gasket or
accelerate this process by heating up the part involved
with a normal hairdrier.
Electrical connection
Before plugging in, ensure that the voltage and
frequency shown on the serial number plate
correspond to your domestic power supply.
Voltage can vary by
±
6% of the rated voltage.
For operation with different voltages, a suitably sized
auto-transformer must be used.
Fig. 3
Fig.
3a
Fig.
3b
Fig.
3c
D185
D045
E
PR132
D336
TECHNICAL SPECIFICATION
The technical data is indicated in the rating plate on the left side inside the appliance.
GB
7
OPERATION
Starting-up and Temperature
Regulation
Insert the plug into the wall socket. Open the
refrigerator door and turn the thermostat knob, to be
found on the upper right side of the inner liner,
clockwise, beyond the «
O
» (STOP) position, to start
the appliance.
Temperature adjustment is obtained by turning the
thermostat knob to the required setting. A medium
setting is generally the most suitable. However, the
thermostat knob setting should be adjusted depending
on the temperature required inside the appliance.
This, in turn, depends on a number of factors such as
the ambient temperature, the number of times the
door is opened, the quantity of food stored and the
location of the appliance. Turn the knob clockwise, to
higher numbers, to obtain a lower temperature, or
anticlockwise if a higher temperature is required.
Fresh food refrigeration
To obtain the best performance:
do not store warm food or evaporating liquids in the
refrigerator;
do cover or wrap the food, particularly if it has a
strong flavour.
Position food so that air can circulate freely round it.
Useful hints:
Meat
(all types): wrap in polythene bags and place on
the glass shelf above the vegetable drawer.
For safety, store in this way only one or two days at
the most.
Cooked foods, cold dishes, etc..:
these should be
covered and may be placed on any shelf.
Fruit and vegetables:
these should be thoroughly
cleaned and placed in the special drawer(s) provided.
Butter and cheese:
these should be placed in special
airtight containers or wrapped in aluminium foil or
polythene bags to exclude as much air as possible.
Milk bottles:
these should have a cap and should be
stored in the bottle rack on the door.
Bananas, potatoes, onions and garlic, if not packed,
must not be kept in the refrigerator.
GB
8
Movable shelves
The walls of the refrigerator are equipped with a
series of runners so that the shelves can be positioned
as desired.
Positioning the door shelf
To permit storage of food packages of various sizes,
the door shelf can be adjusted in height.
To make these adjustments proceed as follows:
Gradually pull the shelf in the direction of the arrows
until it comes free, then reposition as required
(Fig. 5).
Fig. 4
Fig. 5
D040
D113
9
Freezing fresh food
The 4-star compartment ( ) is suitable for long
term storage of commercially frozen food (i.e. for 3
months, unless otherwise stated by the manufacturer),
and for freezing fresh food.
Under normal circumstances, to freeze fresh foods it
is not necessary to change the setting of the
thermostat knob with respect to the normal running
position.
However, for a quicker freezing operation, turn the
thermostat knob to the coldest setting, but remember
that, in this condition, the refrigerating compartment
temperature might drop below 0
°
C. If this occurs
reset thermostat knob to a warmer setting.
To help you make the most of the freezing process,
here are some important hints:
Place the food to be frozen on the shelf.
The maximum quantity of food which can be frozen
in 24 hours is shown on the rating plate.
Only freeze top quality, fresh and thoroughly cleaned
foodstuffs.
Prepare the fresh food in small portions to enable it to
be rapidly and completely frozen and to make it
possible subsequently to thaw only the quantity
required at the time.
Wrap up the food in aluminium foil or polythene and
make sure that the packages are airtight.
It is advisable to show on the single food packet the
freezing-in date to enable you to keep tab of the
storage time.
Do not allow fresh, unfrozen food to touch food
which is already frozen, thus avoiding a rise in
temperature of the latter.
Important
Do not put carbonated liquids (fizzy drinks, etc.) in
the freezing compartment as they may burst.
Water ices, if consumed immediately after removal
from the freezing compartment, can possibly cause
the skin to be freeze burnt.
Remember that, once thawed, frozen food deteriorates
rapidly.
On the rear side of the door you will find a list of
foods followed by a number. These numbers indicate
the maximum period of time for which the food in
question may be conserved (in months).
Storage of frozen food
To obtain the best performance from this appliance,
we strongly recommend that you make sure that the
commercially frozen foodstuffs were adequately
stored by the retailer and, furthermore, be sure that
these frozen foodstuffs are transferred from the
foodstore to the freezer in the shortest possible time (a
temperature increase of the frozen food could shorten
its storage period).
It is also advisable not to exceed the storage period
indicated by the producer of the food.
Finally, do not open the door frequently or leave it
open longer than absolutely necessary.
If there is a power failure when food is in the freezer,
do not open the door of the freezing compartment.
The frozen food will not be affected if the power cut
is of short duration (a temperature increase of the
frozen food could shorten its safe storage period),
otherwise it is recommended that the food should be
used within a very short time.
Thawing
Deep-frozen or frozen food, prior to being used, can
be thawed in the refrigerator compartment or at room
temperature, depending on the time available for this
operation.
Small pieces may even be cooked still frozen, directly
from the freezer: in this case, cooking will take
longer.
10
Defrosting
Frost is automatically eliminated from the evaporator
of the refrigerator compartment every time the motor
compressor stops, during normal use. The defrost
water drains out through a trough into a special
container on the back of the appliance where it
evaporates.
Periodically clean the defrosting water drainage
hole of the refrigerator, using the special cleaner
already inserted into the discharge hole (Fig. 6).
The freezer compartment, however, will become
progressively covered with frost. This should be
removed with the special plastic scraper provided,
whenever the thickness of the frost exceeds 4 mm.
During this operation it is not necessary to switch off
the power supply or to remove the foodstuffs.
However, when the ice becomes very thick on the
inner liner, complete defrosting should be carried out
and it is advisable to carry out this operation when the
appliance is empty.
To carry out complete defrosting of the freezer
compartment ( ) proceed as follows:
Unplug the appliance from the power supply or set the
thermostat on the «
O» position. Remove the ice-cube
trays and the frozen foods and wrap them in several
sheets of newspaper or, even better, in thermally
insulated containers, and then keep them in a cool
place.
Keep the freezer door open and introduce a container
filled with hot water (taking care to place this on a
layer of cardboard) so as to accelerate the defrosting
process.
Absorb all remaining water with a sponge and then
accurately dry the freezer. Reconnect the appliance to
the power supply and then set the thermostat to the
coldest position for approximately 2 hours and then
shift it into the normal functioning status.
Replace the foods previously removed from the
freezer and the ice cubes trays.
Important
Never use knives or metal objects to scrape away the
accumulated frost which might damage the cooling
circuit.
Remember that an increase in the surface temperature
of already-frozen foods may significantly decrease
the duration of their conservation.
Ice-cube production
This appliance is equipped with trays for the
production of ice-cubes.
Fill these trays with water to 3/4 of their height, then
put them in the freezer compartment.
The ice-cubes may be shaken out from the trays by
simply twisting; do not use metallic instruments to
remove the trays from the freezer.
Fig. 6
D037
11
MAINTENANCE
Internal cleaning
Clean the inside and accessories of the refrigerating
compartment with warm water and sodium
bicarbonate (one tablespoon in 4 litres of water).
Rinse and dry thoroughly.
Clean the inside of the freezer compartment after each
complete defrosting.
External cleaning
Wash the outer cabinet with warm soapy water.
Do not use abrasive products.
Once or twice a year dust the condenser (black grill)
and compressor at the back of the appliance with a
brush or vacuum cleaner. An accumulation of dust
will affect the performance of the appliance and cause
excessive electricity consumption.
Periods of non-operation
When the appliance is not in use for long periods,
disconnect from the mains, empty and clean, leaving
the door ajar to prevent unpleasant smells.
Interior light
The light bulb inside the refrigerator compartment can
be reached as follows:
- unscrew the light cover securing screw.
- unhook the moving part as shown in the figure.
Fig. 7
D731
CUSTOMER SERVICE
What to do if the appliance is not
functioning properly.
If something is not working properly, check that:
the plug is firmly in the wall socket and the mains
power switch is on;
there is an electricity supply (find out by plugging in
another appliance);
the thermostat knob is in the correct position.
If the appliance seems too noisy, check that the sides
are not touching furniture that can transmit or amplify
a noise or a vibration. Also, check that the piping of
the refrigerant system does not vibrate.
If there are water drops on the bottom of the cabinet,
check that the defrost water drain opening is not
obstructed.
If your appliance is still not working properly after
making the above checks, contact the nearest service
centre.
To obtain fast service, it is essential that when you
apply for it you specify the model & serial number of
your appliance which can be found on the rating plate.
GB
GB
/
