Swann Advantage Series User manual

— 1 —

Directory

I. DVR Features.........................................................................................................2

II. Layout....................................................................................................................2

2.1 Front Panel............................................................................................................................2

2.2 Rear Panel ............................................................................................................................3

2.3 Remote Control.....................................................................................................................3

III. DVR Installation.......................................................................................................4

3.1 Install Hard Disk....................................................................................................................4

3.2 Connect Camera and Monitor ...............................................................................................5

3.3 Connect Power Cord.............................................................................................................5

IV. DVR System Boot ..................................................................................................5

4.1 Detect Installed Hard Disk.....................................................................................................5

4.2 Recover Lost Data.................................................................................................................6

4.3 Restore Recording Process ..................................................................................................6

4.4 Main Screen..........................................................................................................................7

V. DVR Setup ..............................................................................................................7

5.1 Setup Menu...........................................................................................................................7

5.2 Camera Select.......................................................................................................................8

5.3 Record Select........................................................................................................................9

5.4 Record Mode.........................................................................................................................9

5.5 Record Frame Rate.............................................................................................................10

5.6 Record Quality.....................................................................................................................10

5.7 Record Schedule.................................................................................................................10

5.8 Auto Record………………..………………………………………………………………………11

5.9 Sub Menu-Password Setup……………..………………………………………………………11

5.10 Sub Menu-Password Change............................................................................................. 11

5.11 Sub Menu-Picture Setup.....................................................................................................12

5.12 Sub Menu-Time Setup........................................................................................................12

5.13 Sub Menu-PTZ Setup.........................................................................................................13

5.14 Hard Drive Setup................................................................................................................13

5.15 Alarm Setup........................................................................................................................14

5.16 NTSC/PAL Output Select....................................................................................................17

5.17 Restore Factory Default......................................................................................................17

VI. Record...................................................................................................................18

6.1 Start Recording.....................................................................................................................18

6.2 Stop Recording .....................................................................................................................19

6.3 Recording Length..................................................................................................................19

VII. Playback...............................................................................................................20

VIII USB Programming...............................................................................................21

8.1 Install ....................................................................................................................................21

8.2 Program Interface.................................................................................................................21

IX. Specification..........................................................................................................26

X. Appendix...............................................................................................................27

10.1 System Connect Sketch Map..............................................................................................27

10.2 DVR Contents.....................................................................................................................27

— 2 —

I DVR Features

z 4 Channel BNC Camera Input

z 2 Channel BNC Monitor/VCR Output

z NTSC / PAL

z Video Loss Alarm

z Motion Detection With Area Setting

z PTZ Control With RS-485 Port.

z Connect to PC With USB 2.0 Port, for Playback

z 4 Sets NO/NC Sensor Input

z 1 Alarm Output (2A 28VDC / 2A 125 VAC)

z One ATA-100 Hard Disk Interface, Support Over 200G Byte

z Time Schedule record / Sensor Triggered Record / Motion

Triggered Record

z IR Remote Controller

z

II Layout 2.1 Front Panel

1 Power LED 8 Menu /Exit 15 Forward

2 HDD Access Indicator 9 Move Up 16 Stop

3 Channel 1 10 Select /Edit 17 Record

4 Channel 2 11 IR Window 18 Move Down

5 Channel 3 12 Rewind 19 PTZ Switch

6 Channel 4 13 Pause

7 Quad View 14 Play

— 3 —

1. USB Port 2. Video Output

3. Video Input 4. RS-485/Sensor /Alarm

5. DC Input 6. Power Switch

7. Fan 8. Grounding

1.CH1 Select or enlarge CH1

2.CH2 Select or enlarge CH2

3.CH3 Select or enlarge CH3

4.CH4 Select or enlarge CH4

5.QUAD Quad View

6.REW Rewind or Zoom-

7.PLAY Play record list or Focus+

8.FWD Forward or Zoom+

9.RECORD Record

10.PAUSE Pause or Focus-

11.STOP Stop recording or playing

12. PTZ PTZ Switch

13.MENU Enter or exit setup menu or Move

DOME left

14. UP Move up prompt or Move DOME up

15. Sel/Edit Modify item or Move DOME right

16.DOWN Move down prompt or Move DOME

down

II Layout 2.3 Remote Control

II Layout 2.2 Rear Panel

— 4 —

III DVR Installation 3.1 Installing Hard drive

1. Remove the screws around the top cover.

2. Remove the top cover carefully.

3. Connect the power cord and data cable to hard disk carefully.

Ensure the HDD is set to MASTER.

4. Use the provided screws to fix hard disk on the rack.

5. Then replace the cover the case and fix it to the case.

CAUTION:

Do not open the cover when DVR is running!

Make sure the HDD is set to MASTER.

— 5 —

III DVR Installation 3.2 Connect Camera and Monitor

There are 4 camera inputs and 2 monitor outputs with BNC connectors.

III DVR Installation 3.3 Connect Power Cord

Please use the power adapter supplied with DVR.

IV DVR System Boot 4.1 Detect Installed Hard Disk

HDD Checking………..

After connecting the power, system

will boot-up and detect installed hard

disk. On the Monitor it will show

hard-disk information.

Please make reference to hard disk

manual to configure hard disk drive

to Master.

— 6 —

IV DVR System Boot 4.2 Recover Lost Data

A Power-Error can cause data

to be lost and the system will

ask to ‘Recover HDD’ at the

next start up.

Please press “

Select” to

proceed.

IV DVR System Boot 4.3 Restore Recording Process

RECOVER HDD?

04811-101735

(SELECT) YES/(MENU)NO

POWER ERROR DETECTED

RESTORE HARD DISK (MASTER) OK

RESTORE REC MODE…………… OK

re-connected.

When power-error happens

during recording process, the

system will automatically resume

recording after power is

— 7 —

IV DVR System Boot 4.4 Main Screen

V DVR Setup 5.1 Setup Menu

With the DVR running, the

monitor will show the view f

rom the cameras.

Upper left Æ percentage of

hard disk space used.

Middle Æ channel name (C

H1  CH4).

Bottom right Æ date and

time shown.

1. Bottom left Æ Mode,

Status, HD Info, Schedule -

mode of DVR. Refer to

6.1

Start Recording

Eg. DVR is in record mode,

waiting for stop key press.

Then press “

30%

Menu” on

DVR to enter setup process.

MAIN MENU

C

AMERA SELECT 1234

RECORD SELECT 1234

RECORD MODE EACH

RECORD FRAMERATE 25

VIDEO QUALITY NORMAL

RECORD SCHEDULE

SUB MENU

HARD DISK SETUP

ALARM SETUP

RESTORE FACTORY DEFAULT

PRESSUPDOWN. THEN(SELECT)

PRESS(MENU) TO EXIT



Press “ Menu” to enter setup

menu,

Use “

Up” and “ Down” to

select item,

Press “

Select” to modify

settings and “

Menu” to exit.

— 8 —

Menu Directory

Camera Select

Main Menu

Record Select

Record Mode

Record Frame Rate

Video Quality

Record Schedule

Sub Menu

Hard Drive Setup

PTZ Setup

Auto Record

Password Setup

Password Change

Picture Setup

Time Setup

Alarm Setup

Restore Factory Default

V DVR Setup 5.2 Camera Select

The DVR system can

display 4 cameras and video in

one picture (Quad Mode).

Users can configure which

camera is allowed to display.

Press “

Select” to modify

setting and press “

CH1”, “

CH2”, “

CH3”,“ CH4” to set

each channel separately.

If the channel is disabled,

the system will display “OFF”

on monitor.

— 9 —

V DVR Setup 5.3 Record Select

eo.

Configure which channel is allowed to record.

V DVR Setup 5.4 Record Mode

There are two modes for video recording,

Each Mode The DVR will compress and record each video channel

separately therefore, the user can enlarge a single

channel to full screen display. For example, the user can

turn off the record function of CH-1 and CH-2 and then

the system will only record CH3 and CH4 vid

Press “

CH1”, “ CH2”, “ CH3”, “ CH4” to switch

between channels when playing back recorded video.

Loop FunctionWith system in play back mode or recording, press the

“QUAD” button and hold for three (3) seconds to make each video channel

enlarge to full screen.

The full screen will be displayed for five (5) seconds.

The loop will continue until any button is pushed.

ngle

Quad ModeThe DVR will compress and record all 4 video channels

into one file, therefore the user cannot enlarge a si

channel to full screen in play back mode. User can’t use

the video loop function in this mode.

V DVR Setup 5.5 Record Frame Rate

— 10 —

Record frame rate

will affect the movement of object in recorded video.

More frames per second gives more smooth movement and uses more hard

disk space.

System default value is 25 fps for PAL (NTSC is 30fps), that means the

system will record 25 frames per second. User can set frame rate as for PAL

25,12,8,6,4,3,2,1 frames per second (NTSC is 30,15,10,7,5,4,3,2,1)

V DVR Setup 5.6 Record Quality

There are three level of record quality, High, Normal and Low.

Higher quality uses more hard disk space.

Record frame rate, record quality and hard disk space will affect total

record time of DVR system.

V DVR Setup 5.7 Record Schedule

User can setup video record method by time, Sensor Triggered or Motion

Triggered and Continuous Recording.

RECORD SCHEDULE

TTTAAATTTTTTAAAATTTTTTTT-



│ │ │ │ │ │ │ │ │

0 3 6 9 12 15 18 21 24

PRESSUPDOWN. THEN(SELECT)

PRESS(MENU) TO EXIT

Works with many kinds of external

sensor equipment like PIR, Gas sensor.

DVR will not record video until external

sensor is triggered and outputs signal to

notify DVR during this specified period of

time.

Button function:

 Up Down:move the prompt 

Select:Select Method.

“-” No Record

“T” Continuous, (System default)

“A” Sensor Triggered or Motion Triggered.

V DVR Setup 5.8 Sub Menu-Auto Record

— 11 —

When you select “ON” DVR will be active to record automatically if

DVR has not been operated in five min

utes.

When you choose “OFF” DVR will not record until you press “RECORD”

button.

V DVR Setup 5.9 Sub Menu-Password Setup

When password set is “ON”, Stop recording or enter menu will need

Password. If password set is “OFF”, option is disabled.

V DVR Setup 5.10 Sub Menu-Password Change

System default password: Press “ CH1” button six times.

CURRENT PASSWORD :……

NEW PASSWORD :……

CONFIRM PASSWORD :……

User needs to enter six

characters for the

password.

All keys can be used as

password key except the

“

Menu” key, which is

used to exit.

— 12 —

V DVR Setup 5.11 Sub Menu-Picture Setup

HUE: 0-99

SATURATION: 0-99

CONTRAST: 0-99

BRIGHTNESS: 0-99

Button functions:

 Up Down:move the prompt

REW:Increase Value

FWD:Reduce Value

CH1-CH4,QUAD:Select Channel

 Menu:exit.

V DVR Setup 5.12 Sub Menu-Time Setup

TIME SETUP



2006/01/18 08:30:00

PRESS(UP,DOWN), THEN(SELECT)

PRESS(MENU) TO EXIT

Configure DVR system time.

Press

Upand Downto

move prompt and press 

Selectto modify. Press



Menuto save and exit.

V DVR Setup 5.13 Sub Menu-PTZ Setup

— 13 —

PTZ SETUP

CHANNEL ADDRESS PROTOCOL BAUD RATE

1 1 PELCO-D 2400

2 2 PELCO-D 2400

3 3 PELCO-D 2400

4 4 PELCO-D 2400

(<,>)MOVE (<<,>>)ADJUST (MENU)EXIT



CHANNEL: Camera Number

ADDRESS: Speed Dome’s address,

Can be changed from 0 to 255

PROTOCOL: Supports “PELCO-D”,

“PELCO-P”, “SAMSUNG”, “BO1”, “NEON”,

“CTNCOM”, Set the protocol according to

the Speed dome’s protocol.

BAUD RATE: Press “EDIT” button to select

the value. Can be changed from 1200bps to

19200bps, the default value is 2400bps

If user has compatible Speed Domes attached to DVR, press the “PTZ” button and

select the camera number that you wish to control. Now, user can use

“Up”, ”Down”, ”Right”, ”Left” buttons to control the Speed dome’s horizontal and vertical

position. Press “ REW”,”FWD”,”PAUSE” and “PLAY” buttons to control Speed Dome’s

ZOOM and FOCUS functions.

Notice: Make sure that all the lines are connected to the Speed Domes correctly, and

the protocol, baud rate and address parameters are set correctly also.

V DVR Setup 5.14 Hard Drive Setup

/

HARD DISK SETUP

OVERWRITE ENABLED [YES]

MASTER HDD SIZE 120042MB

MASTER HDD USED 80865MB 77%

MASTER HDD FORMAT

SLAVE HDD SIZE N/A

SLAVE HDD USED N/A

SLAVE HDD FORMAT

PRESS(UP,DOWN), THEN(SELECT)

PRESS(MENU) TO EXIT

OVERWRITE ENABLED:

If you choose YES, recording continues

and overwrites previous recording when hard

disk drive space is full.

If you choose NO, the recording process

stops when all hard disk drive is full for

recording.

MASTER HDD SIZE:

It shows the size of the master hard disk

drive installed in the DVR.

MASTER HDD USED:

— 14 —

It shows the space used on the master hard disk drive for recording and the percent of

the used hard disk.

MASTER HDD FORMAT:

If you format the hard drive, it will erase all the data recorded on the master hard disk

drive.

Notice: when you first use a HDD in the DVR, please use this function to format the

HDD. Otherwise the computer will not find the HDD when you connect the DVR to the

computer by using the USB cable.

SLAVE HDD N/A

V DVR Setup 5.15 Alarm Setup

ALARM RECORD DURATION

The number indicates how long

triggered recording lasts after the

sensors are triggered or the

movements in front of the camera.

ALARM DURATION

It controls how long (in seconds)

the alarm lasts after the system is

triggered.



ALARM SETUP

ALARM RECORD DURATION 5

ALARM DURATION OFF

BUZZER DURATION OFF

SENSOR SETUP

MOTION SETUP

PRE

SS(UP

,

DOWN

), THEN(SELECT)

BUZZER DURATION

Buzzer time set (OFF,05,10,15,20,25,30 seconds and CONT) , User

can press [

Select ] to set the time .When Buzzer Time is “OFF”,

the buzzer will be shut off. When “Buzzer Time” is “CONT”, the buzzer

will work continuously.

— 15 —

Sensor Setup

There are 3 different modes for sensor setting:

NOT INSTALLED, NORMAL-CLOSE and

NORMAL-OPEN.

It depends on what type of external sensor

you are using. If sensor’s output is

NORMAL-OPEN then select NORMAL-OPEN

mode in DVR.

SENSOR SETUP

CHANNEL-1 TYPE:NORMAL-OPEN

CHANNEL-2 TYPE:NORMAL-CLOSE

CHANNEL-3 NOT INSTALLED

CHANNEL-4 NOT INSTALLED

PRESSUPDOWN. THEN(SELECT)

PRESS(MENU) TO EXIT

If the sensor connected to the DVR is triggered by an intruder, then the

DVR will automatically start recording process.

Note: the recording method is set to alarm recording in the first place.

Sensor Input 1 2 3 4

PTZ

Alarm Out

Push the UNLOCK BUTTON to insert and pull out the wire

Install example diagram:

— 16 —

Motion Setup

1. User setup video record method by Motion Trigger. Reference 5.7.

MOTION DETECTION SETUP

CHANNEL 1 SENSITIVITY 4

CHANNEL 2 SENSITIVITY 4

CHANNEL 3 SENSITIVITY 4

CHANNEL 4 SENSITIVITY 4

CHANNEL 1 AREA SET

PRESS(UP,DOWN), THEN(SELECT)

PRESS

(

MENU

)

TO EXIT

CHANNEL 1- 4 SENSITIVITY:

Press “

Select” to adjust

sensitivity of motion detection.

High (1----------9,OFF) Low

When it’s OFF, the channel cannot

be triggered by movement.

CHANNEL 1- 4 AREA SET:

Press “

Select” to enter area

setting state, the picture of selected

channel is divided into 144(12*12)

blocks, and then press “REW” to

move left, press “FWD” to

move right, press “UP” to move up, press “DOWN” to move down, press “

Select” to set the block to being active or not.

When the block is transparent, it’s active to record.

When the block is covered by shadow, it is not active. NO Recording.

After completing the “MOTION SET”, User can exit MENU, And press

[ Record ] to start Motion Record.

V DVR Setup 5.16 NTSC/PAL Output Select

— 17 —

Change jumper J10 to select NTSC or PAL video output format according to

the silkscreen on the PCB.

NTSC/PAL Select

V DVR Setup 5.17 Restore Factory Default

ALL SETTING DATA IS INITIALIZED

If user selects this item, the

system will restore all user’s

settings to factory default values,

and DVR will reboot.

VI Record 6.1 Start Recording

— 18 —

Press “ Record” to start recording according to the record schedule

that user has set. System will display some information on Screen.

Only EACH MODE can enlarge single channel to full screen display

QUAD REC [M] (T) 2008/07/01 16:22:30

10%

R

1

3

2

4

5

6

7

8

1. Hard Disk Usage (Displayed as a percentage)

2. Recording Symbol

3. Channel Name

4. Mode (QUAD or EACH)

5. Status (REC, Play, FF1, FF2, FF3, REW, PAUSE)

6. HD Info. ([M] Master disk [S] Slave disk)

7. Schedule (T) Continuous (A) Sensor or Motion () No Record

8. The time and date of the DVR

VI Record 6.2 Stop Recording

— 19 —

Press “ Stop” and system will prompt you to input password. Only

correct password can stop recording process. This is with Password option

enabled. With Password option disabled, Press “

Stop” will stop recording.

Estimated record time based on 80G Byte HD (Quad Mode) Unit: Hours

Format Quality Frame Rate

30 15 7 1

HIGH 20 38 78 167 1165

User can calculate and estimate record hours by below formula

80G Byte @ 7 frames per second @ Normal quality

80 (G byte) x 1024 (M byte) x 1024 (K byte)

in)

15 (Kbyte/frame) x 7 (frame/sec) x 60 (sec) x 60 (m

Estimate hours is 222 Hours

NORMAL 15 52 103 222 1533

NTSC

LOW 12 64 129 277 1942

Format Quality Frame Rate 25 12 6 1

HIGH 20 46 97 194 1165

NORMAL 15 62 129 258 1553

PAL

LOW 12 78 162 323 1942

VI Record 6.3 Recording Length

VII Playback 7.1 Play

— 20 —

Press “

Play” ,then system will list all recorded video clip from HD.

Newest video will be at top of the list, press “

Move Up” and “ Move

Down” to select start time and press “

Play” again to start play video to

the end.

1.Hard Disk usage 4. End Time

2. HD Information (Master or Slave) 5. TIME: Continue record

3. Start Time

6. ALARM: Sensor or Motion Triggered

Another way to search video is directly input time period. Press “

Forward” and then press “

Up” and “ Down” to move prompt. Press

“

Select” to edit time value and press “ Play” to play video.

VIII USB Programming 8.1 Installation

2008 /0 1 / 0 8 08 : 30 : 3 2 --- 2008/0 1 / 0 8 16 : 00 : 05

 2008/01/08 16:00:35

2008/01/08 15:50:20

2008/01/08 14:30:56

2008/01/08 14:15:30

2008/01/08 14:00:15

2008/01/08 13:55:37

2008/01/08 11:30:12

2008/01/08 10:15:30

2008/01/08 08:30:55

MOVESELECTCHANGE PLAYPLAY

MENUEXIT SELECT EVENT OR TIME

4

*

SEARCH TIME

2008/01/08 08:30:56

01 TIME

02 TIME

03 TIME

04 TIME

05 ALARM

06 ALARM

07 ALARM

08 ALARM

/

50%

1

3

5

6

5



HARD DRIVE:

2



Page is loading ...

Swann Advantage Series User manual

Swann Advantage Series User manual

Related papers

Other documents