TP-LINK TL-SG108PE User manual

Brand: TP-LINK

Model: TL-SG108PE

Category: Network switches

Type: User manual

This manual is also suitable for

TL-SG105E/TL-SG108E/TL-SG108PE

TL-SG1016DE/TL-SG1024DE

Gigabit Easy Smart Switch

REV1.0.3

1910011479

Specifications are subject to change without notice. is a registered trademark of

TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or

registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any

derivative such as translation, transformation, or adaptation without permission from TP-LINK

reserved.

http://www.tp-link.com

FCC STATEMENT (For TL-SG105E/TL-SG108E/TL-SG108PE only)

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause

undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

CE Mark Warning (For TL-SG105E/TL-SG108E/TL-SG108PE only)

This is a class B product. In a domestic environment, this product may cause radio interference, in

which case the user may be required to take adequate measures.

Industry Canada Statement (For TL-SG105E/TL-SG108E/TL-SG108PE only)

CAN ICES-3 (B)/NMB-3(B)

BSMI Notice (For TL-SG105E/TL-SG108E/TL-SG108PE only)

安全諮詢及注意事項

 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

 注意防潮，請勿將水或其他液體潑灑到本產品上。

 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。

 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。

FCC STATEMENT (For TL-SG1016DE/TL-SG1024DE only)

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause

undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

CE Mark Warning (For TL-SG1016DE/TL-SG1024DE only)

This is a class A product. In a domestic environment, this product may cause radio interference, in

which case the user may be required to take adequate measures.

Industry Canada Statement (For TL-SG1016DE/TL-SG1024DE only)

CAN ICES-3 (A)/NMB-3(A)

BSMI Notice (For TL-SG1016DE/TL-SG1024DE only)

安全諮詢及注意事項

 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

 注意防潮，請勿將水或其他液體潑灑到本產品上。

 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。

 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。

此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被

要求採取某些適當的對策。

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам

нормативних документів та вимогам, що передбачені чинними законодавчими актами

України.

Safety Information

 When product has power button, the power button is one of the way to shut off the product;

When there is no power button, the only way to completely shut off power is to disconnect the

product or the power adapter from the power source.

 Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and

voiding the limited warranty. If you need service, please contact us.

 Avoid water and wet locations.

This product can be used in the following countries:

AT BG BY CA CZ DE DK EE

ES FI FR GB GR HU IE IT

LT LV MT NL NO PL PT RO

RU SE SG SK TR UA US

III

Explanation of the symbols on the product label

Symbol Explanation

AC voltage

DC voltage

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic

equipme

nt (WEEE). This means that this product must be handled pursuant to

European directive 2012/19/EU in order to be recycled or dismantled to minimize

its impact on the environment.

User has the choice to give his product to a competent recycling organization or to

the retailer when he buys a new electrical or electronic equipment.

DECLARATION OF CONFORMITY

For the following equipment:

Product Description: Gigabit Easy Smart Switch

Model No.: TL-SG105E/TL-SG108E/TL-SG108PE/TL-SG1016DE/TL-SG1024DE

Trademark: TP-LINK

We declare under our own responsibility that the above products satisfy all the technical

regulations applicable to the product within the scope of Council Directives:

Directives 2004 / 108 / EC, Directives 2006 / 95 / EC, Directives 2011/65/EU

The above product is in conformity with the following standards or other normative documents：

EN 55022: 2010 + AC: 2011

EN 55024: 2010

EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 +A2: 2013

The product carries the CE Mark

Person responsible for making this declaration:

Yang Hongliang

Product Manager of International Business

Date of issue: 2015-11-16

TP-LINK TECHNOLOGIES CO., LTD.

Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,

Shennan Rd, Nanshan, Shenzhen, China

CONTENTS

Package Contents ............................................................................................................................ 1

Chapter 1 About this Guide ............................................................................................................ 2

1.1 Intended Readers ........................................................................................................... 2

1.2 Conventions ................................................................................................................... 2

1.3 Overview of This Guide .................................................................................................. 2

Chapter 2 Introduction .................................................................................................................... 4

2.1 Overview of the Switch ................................................................................................... 4

2.2 Appearance Description ................................................................................................. 4

2.2.1 Front Panel .......................................................................................................... 4

2.2.2 Rear Panel .......................................................................................................... 7

Chapter 3 Login to the Switch ........................................................................................................ 9

3.1 Login ............................................................................................................................... 9

3.2 Configuration .................................................................................................................. 9

Chapter 4 System .......................................................................................................................... 11

4.1 System Info ................................................................................................................... 11

4.2 IP Setting ....................................................................................................................... 11

4.3 User Account ................................................................................................................ 12

4.4 System Tools ................................................................................................................ 13

4.4.1 Backup and Restore .......................................................................................... 13

4.4.2 System Reboot .................................................................................................. 14

4.4.3 System Reset .................................................................................................... 14

4.4.4 Firmware Upgrade............................................................................................. 15

Chapter 5 Switching ..................................................................................................................... 16

5.1 Port Setting ................................................................................................................... 16

5.2 IGMP Snooping ............................................................................................................ 17

5.3 Port Trunk ..................................................................................................................... 18

Chapter 6 Monitoring .................................................................................................................... 20

6.1 Port Statistics ................................................................................................................ 20

6.2 Port Mirror .................................................................................................................... 21

6.3 Cable Test .................................................................................................................... 22

6.4 Loop Prevention ........................................................................................................... 23

Chapter 7 VLAN............................................................................................................................ 25

7.1 MTU VLAN ................................................................................................................... 26

7.2 Port Based VLAN ......................................................................................................... 27

7.3 802.1Q VLAN ............................................................................................................... 28

7.4 802.1Q PVID Setting .................................................................................................... 30

Chapter 8 QoS .............................................................................................................................. 32

8.1 QoS Basic .................................................................................................................... 34

8.2 Bandwidth Control ........................................................................................................ 36

8.3 Storm Control ............................................................................................................... 37

Appendix A: Specifications ............................................................................................................. 39

Package Contents

The following items should be found in your box:

 One Gigabit Easy Smart Switch

 One power cord

 Two mounting brackets and other fittings (for TL-SG1016DE/TL-SG1024DE only)

 Installation Guide

 Resource CD for TL-SG105E/TL-SG108E/TL-SG108PE/TL-SG1016DE/TL-SG1024DE

switch, including:

• This User Guide

• Easy Smart Configuration Utility.exe

• Easy Smart Configuration Utility User Guide

• Other Helpful Information

Note:

Make sure that the package contains the above items. If any of the listed items are damaged or

missing, please contact your distributor.

Chapter 1 About this Guide

This User Guide contains information for setup and management of TL-SG105E/TL-SG108E/

TL-SG108PE/TL-SG1016DE/TL-SG1024DE Gigabit Easy Smart Switch. Please read this guide

carefully before operation.

1.1 Intended Readers

This Guide is intended for network managers familiar with IT concepts and network terminologies.

1.2 Conventions

In this Guide the following conventions are used:

 The switch or TL-SG105E/TL-SG108E/TL-SG108PE/TL-SG1016DE/TL-SG1024DE

mentioned in this Guide stands for TL-SG105E/TL-SG108E/TL-SG108PE/TL-SG1016DE/

TL-SG1024DE Gigabit Easy Smart Switch without any explanation.

Tips:

The TL-SG105E/TL-SG108E/TL-SG108PE/TL-SG1016DE/TL-SG1024DE are sharing this User

Guide. They just differ in the number of LED indicators and ports. For simplicity, we will take the

operation on TL-SG1016DE for example throughout the configuration chapters. However,

differences with significance will be presented with figures or notes as to attract your attention.

 Menu Name→Submenu Name→Tab page indicates the menu structure. System→System

Info→System Summary means the System Summary page under the System Info menu

option that is located under the System menu.

 Bold font indicates a button, a toolbar icon, menu or menu item.

Symbols in this Guide：

Symbol Description

Note:

Ignoring this type of note might result in a malfunction or damage to the device.

Tips:

This format indicates important information that helps you

make better use of your

device.

1.3 Overview of This Guide

Chapter Introduction

Chapter 1 About This Guide Introduces the guide structure and conventions.

Chapter Introduction

Chapter 2 Introduction Introduces the feature

s, application and appearance of

TL-SG105E/TL-SG108E/TL-SG108PE/TL-SG1016DE/TL-SG1024DE

switch.

Chapter 3 Login to the Switch Introduces how to log on to the Web management page.

Chapter 4 System This module is used to configure system properties of th

e switch.

Here mainly introduces:

 System Info:

View device information and define the device

description.

 IP Setting: Get and modify the network parameters of the switch.

 User Account: Modify the username and password for users to log

on to the Web management page.

 System Tools: Manage the configuration file of the switch.

Chapter 5 Switching Configure the basic functions of the switch.

Chapter 6 Monitoring Monitor the traffic information of the switch, and provide the

convenient method to locate and solve the network problem.

Chapter 7 VLAN

This module is used to configure VLANs to control broadcast in LANs.

Here mainly introduces:

 MTU VLAN: Set the MTU VLAN mode.

 Port Based VLAN: Set the Port-Based VLAN mode

 802.1Q VLAN: Set the 802.1Q Tag VLAN mode.

 802.1Q PVID Setting: Configure 802.1Q PVID value.

Chapter 8 QoS

This module is used to configure QoS function to provide different

quality of service for various network applications and requirements.

Here mainly introduces:

 QoS Basic: Configure and view the basic parameters of QoS.

 Bandwidth Control: Configure and view the

bandwidth control

function information.

 Storm Control: C

onfigure and view the storm control function

information.

Appendix A Specifications Lists the hardware specifications of the switch.

Return to CONTENTS

Chapter 2 Introduction

Thanks for choosing the TL-SG105E/TL-SG108E/TL-SG108PE/TL-SG1016DE/TL-SG1024DE

Gigabit Easy Smart Switch!

2.1 Overview of the Switch

The TL-SG105E/TL-SG108E/TL-SG108PE/TL-SG1016DE/TL-SG1024DE Gigabit Easy Smart

Switch is an ideal upgrade from an unmanaged switch, designed for Small and Medium Business

networks that require simple network management. Network administrators can effectively monitor

traffic via Port Mirroring, Loop Prevention and Cable Test features. To optimize traffic on your

business network, they offer port-based, tag-based, DSCP-based QoS to keep latency-sensitive

traffic moving smoothly and jitter-free. Additionally, port-based, tag-based and MTU VLAN can

improve security and meet more network segmentation requirements. Moreover, with the

innovative energy-efficient technology, they are eco-friendly solution for your business network.

Note:

For details about Easy Smart Configuration Utility, please refer to the User Guide of the Easy

Smart Configuration Utility in the Resource CD.

2.2 Appearance Description

2.2.1 Front Panel

 TL-SG105E/TL-SG108E

The front panel of TL-SG105E is shown as Figure 2-1.

Figure 2-1 Front Panel of

TL-SG105E

The front panel of TL-SG108E is shown as Figure 2-2.

Figure 2-2 Front Panel of

TL-SG108E

The following parts are located on the front panel of the switch:

 Reset: With the switch powered on, press this button for five seconds or above to reset the

software setting back to factory default setting. (For TL-SG108E only)

 1000Mbps Ports: Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or

1000Mbps. Each has a corresponding 1000Mbps LED and 10/100Mbps LED.

 LEDs

Name Status Indication

Power

On Power is on.

Flashing Power supply is abnormal.

Off Power is off or power supply is abnormal.

1000Mbps

A 1000Mbps device is connected to the corresponding port.

Flashing

Data is being transmitted or received.

Off

A 10/100Mbps device or no device is connected to the

corresponding port.

10/100Mbps

A 10/100Mbps device is connected to the corresponding port.

Flashing Data is being transmitted or received.

Off No device is connected to the corresponding port.

 TL-SG108PE

The front panel of TL-SG108PE is shown as Figure 2-3.

Figure 2-3 Front Panel of

TL-SG108PE

The following parts are located on the front panel of the switch:

 Reset: With the switch powered on, press this button for five seconds or above to reset the

software setting back to factory default setting.

 1000Mbps Ports: Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or

1000Mbps. Each has a corresponding Link/Act LED (Left LED).For Port 1– 4, each of them

also has a PoE Status LED (Right LED).

 LEDs

Name Status Indication

Power

On Power is on.

Flashing Power supply is abnormal.

Off Power is off or power supply is abnormal.

PoE Max

On The total power supply< 55W.

Flashing The total power supply≥ 55W.

Off The total power supply< 46W.

Link/Act

On(Green)

A 1000Mbps device is connected to the corresponding port.

On(Yellow)

A 10/100Mbps device is connected to the corresponding port.

Flashing

Data is being transmitted or received.

Off

No device is connected to the corresponding port.

PoE Status

The port is supplying power normally.

Flashing The port is supplying power abnormally.

Off No PoE power supply is provided on the port.

 TL-SG1016DE/TL-SG1024DE

The front panel of TL-SG1016DE is shown as Figure 2-4.

Figure 2-4 Front Panel of TL-SG1016DE

The front panel of TL-SG1024DE is shown as Figure 2-5.

Figure 2-5 Front Panel of TL-SG1024DE

The following parts are located on the front panel of the switch:

 Reset: With the switch powered on, press this button for five seconds or above to reset the

software setting back to factory default setting.

 1000Mbps Ports: Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or

1000Mbps. Each has a corresponding 1000Mbps LED and Link/Act LED.

 LEDs

Name Status Indication

Power

On Power is on.

Flashing Power supply is abnormal.

Off Power is off or power supply is abnormal.

1000Mbps

A 1000Mbps device is connected to the corresponding port.

Off

A 10/100Mbps device or no device is connected to the

corresponding port.

Link/Act

A device is connected to the corresponding port but no activity.

Flashing Data is being transmitted or received.

Off No device is connected to the corresponding port.

2.2.2 Rear Panel

 TL-SG105E/TL-SG108E/TL-SG108PE

The rear panel of TL-SG105E/TL-SG108E/TL-SG108PE features a power socket and a

Kensington Security Slot (marked with

). TL-SG105E also has a Reset button located on the rear

panel.

Figure 2-6 Rear Panel of

TL-SG105E

Figure 2-7 Rear Panel of

TL-SG108E

Figure 2-8

Rear Panel of TL-SG108PE

 Reset: With the switch powered on, press this button for five seconds or above to reset the

software setting back to factory default setting. (For TL-SG105E only)

 Kensington Security Slot: Secure the lock (not provided) into the security slot to prevent the

device from being stolen.

 DC Power Socket: Connect the female connector of the power cord here, and the male

connector to the DC power outlet. Please make sure the voltage of the power supply meets the

requirement of the input voltage.

 TL-SG1016DE/TL-SG1024DE

The rear panel of TL-SG1016DE/TL-SG1024DE features a power socket and a Grounding

Terminal (marked with

Figure 2-9 Rear Panel of TL-SG1016DE

Figure 2-10 Rear Panel of TL-SG1024DE

 Grounding Terminal: TL-SG105E/TL-SG108E/TL-SG108PE/TL-SG1016DE/TL-SG1024DE

already comes with Lightning Protection Mechanism. You can also ground the switch through

the PE (Protecting Earth) cable of AC cord or with Ground Cable.

 AC Power Socket: Connect the female connector of the power cord here, and the male

connector to the AC power outlet. Please make sure the voltage of the power supply meets the

requirement of the input voltage.

Return to CONTENTS

Chapter 3 Login to the Switch

3.1 Login

1) To access the configuration utility, open a web-browser and type the default address

http://192.168.0.1 in the address field of the browser, then press the Enter key.

Figure 3-1 Web-browser

Tips:

To log in to the switch, the IP address of your PC should be set in the same subnet addresses of

the switch. The IP address is 192.168.0.x ("x" is any number from 2 to 254), Subnet Mask is

255.255.255.0.

2) After a moment, a login window will appear, as shown in Figure 3-2. Enter admin for the User

Name and Password, both in lower case letters. Then click the Login button or press the Enter

key.

Figure 3-2 Login

3.2 Configuration

After a successful login, the main page will appear as Figure 3-3, and you can configure the

function by clicking the setup menu on the left side of the screen.

Figure 3-3 Main Setup-Menu

Note:

Clicking Apply can only make the new configurations effective before the switch is rebooted. If

you want to keep the configurations effective even the switch is rebooted, please click Save

Config. You are suggested to click Save Config before cutting off the power or rebooting the

switch to avoid losing the new configurations.

Return to CONTENTS

Chapter 4 System

The System module is mainly for basic settings of the switch, including four submenus: System

Info, IP Setting, User Account and System Tools.

4.1 System Info

On this page you can view the system information and define the device description.

Choose the menu System→System Info to load the following page.

Figure 4-1 System Info

The following entries are displayed on this screen:



System Info

Device Description: Displays the device model number.

MAC Address: Displays the MAC address of the switch.

IP Address:

Displays the system IP address

of the switch. The default system

IP is 192.168.0.1 and you can change it appropriate to your needs.

Subnet Mask: Displays the subnet mask of the switch.

Default Gateway: Displays the default gateway of the switch.

Firmware Version:

Displays the installed software version number.

Hardware Version:

Displays the installed device hardware version number.

Device Description: Give a description to the device for identification.

4.2 IP Setting

Each device in the network possesses a unique IP Address. You can log on to the Web

management page to operate the switch using this IP Address.

On this page you can get and modify the network parameters of the switch.

Choose the menu System→IP Setting to load the following page.

Figure 4-2 IP Address Setting

The following entries are displayed on this screen:



IP Address Setting

DHCP Setting: Allows you to enable or disable the switch to serve as

DHCP

clien

t. If DHCP client is enabled, the switch will obtain the IP

address, subnet mask and default gateway from the DHCP s

erver

automatically; otherwise, these three items

should be configured

manually. By default, it is disabled.

IP Address:

Specify the system IP address

of the switch. The default system IP

address

is 192.168.0.1 and you can change it appropriate to your

needs. The

switch IP address must be compliant with the subnet

layout.

Subnet Mask: Enter the subnet mask of the switch. Subnet mask is an ad

dress

code that determines the size of the network.

By default, the

switch uses 255.255.255.0 as the subnet mask.

Default Gateway: Enter the default gateway of the switch. Gateway s

erves as the

default destination where the packet is to be forwarded when

its

destination IP address is not within the switch’s subnet.

Note:

1. The switch only possesses an IP address. The IP address newly configured will replace the

original one.

2. Changing the IP address to a different IP segment will interrupt the network communication, so

please keep the new IP address in the same IP segment with the local network.

4.3 User Account

On this page you can modify the username and password in order to refuse illegal users.

Choose the menu System→User Account to load the following page.

Page is loading ...

TP-LINK TL-SG108PE User manual

Brand: TP-LINK

Model: TL-SG108PE

Category: Network switches

Type: User manual

This manual is also suitable for

Download PDF

report

TP-LINK TL-SG108PE User manual

This manual is also suitable for

TP-LINK TL-SG108PE User manual

Related papers

Other documents