Sapido HF-3205 Quick setup guide

Sapido
Brand
Sapido
Model
HF-3205
Category
Networking
Type
Quick setup guide
5 Port Smart Fast Ethernet Switch HF-3205
Quick Installation Guide (V1.1)
One (1) 5 Port Smart Fast Ethernet Switch
One (1) Power Adapter
One (1) Quick Installation Guide
Package Includes
【Front Panel】
【Rear Panel】
Diagram of Functions
Link/Act/Loop
Power
QoS Push Button Switch
Power
Connector
10/100Mbps Ethernet Ports
LED Indicators
For definitions of LED indicators, please refer to the following table：
LED
Power
Link/Act/
Loop
Light
Steady Green
Off
Flashing Reddish
Orange
Steady Green
Blinking Green
Flashing Green
every second
Off
Status
Power is on
Power is off
Loop is detected
Network connection established,
10/100 Mbps connected
Transmitting or receiving data,
10/100Mbps connection activity
Loop is detected
No connection
※ Cat.5 TP is recommended
Cable Type
For cable selection, please refer to the following table:
Plug Connector
RJ-45
RJ-45
Port Type
100BASE-TX
10BASE-TX
Cable Type
Cat. 5 UTP/STP
Cat. 3, 4, 5 UTP/STP
Bandwidth Ratio
8
4
1
Ethernet Port
Red
Yellow
Green
Bandwidth Priority
The Highest
Higher
High
QoS Push Button Switch
You can choose Normal mode or QoS mode via QoS push button
switch. Press the button to activate bandwidth management.
Normal Mode：The bandwidth of red, yellow, and green ports is all the same.
QoS Mode：The bandwidth priority divides into three kinds.
5
4 3
2
1
www.sapido.com.tw
886-6-2280698 886-6-2293658
383, Sec. 2, Minsheng Rd.,West Central District,
Tainan City700,Taiwan
SAPIDO Technology Inc.
ser[email protected]
The SAPIDO HF-3205 Switch does not require any software configuration. You can immediately use the switch after plugging in the RJ-45 Ethernet
cables and turning on the power. The switch can be used according to following steps:
※ Additional Statement:
If you would like to switch between the modes, QoS and Normal. Make sure to repower the switch after you change the mode.
First, please select the mode as normal mode or QoS mode which you would like to use.
Frequently Asked Questions
Normal Mode
1.Mode Select
Confirm the button on the
rear panel stay in Normal
mode.
Installation
Normal
Smart
5
4 3
2
1
5
4 3
2
1
4.Power the Switch On
3.Connecting Switch to a
Computer
Use a second Ethernet cable
to connect a PC to any other
Ethernet port on the switch.
2.Connecting Switch to Internet
Use an Ethernet cable to
connect the modem or router
to any of the Ethernet ports
on the switch.
4. Power the Switch On
Connect the power adapter into the
appropriate slot on the back of the
switch, and confirm the corresponding
LEDs are on properly.
3. Connecting Switch to a Computer
2.Connecting Switch to Internet
Use an Ethernet cable to connect your
modem or router to one of the green
ports on the switch. We recommend
connecting your Internet source cable
to the green port. Leave the red port
available.
Connect the power adapter
into the appropriate slot on
the back of the switch, and
confirm the corresponding
LEDs are on properly.
Use a second Ethernet cable to connect
a PC to any other Ethernet port on the
switch. (If you play on-line game or
watch high quality multimedia, we
recommend connecting to the red
Ethernet port for the highest priority.)
QoS Mode
1.Mode Select
Confirm the button on the rear panel
switch to Smart mode.
Q：What should I do if the Power LED is off?
A：If the Power LED is off, it means that the switch is also powered off.
You will need to check whether the power adapter is properly plugged
in the socket. If you have confirmed that it is plugged in appropriately,
make sure that the socket is on. It is important to make sure that
the power adapter is connected with the power connector tightly.
Q：If my device is connected, why is the Link/Act/Loop LED light not on?
A：Ensure that the cable connectors are securely plugged into the
switch and the device. Also, double check that the connected device
is powered on and has been installed correctly.
Q：How do I get a loop corrected when loop indicators flash?
A：The power indicator and the error indicator will flash when a loop
occurs. At this point, pull out the cable on the port with flashing
indicator immediately to prevent a broadcast storm. Check what
caused the loop and get it fixed.
The most common mistake that usually occurs:
1. Wrong Wiring : When you connect the first switch to the second
switch and connect the second switch back to the first one. It then
causes a loop.
2. Complex Switch Wiring : A loop may happen if you connect your
switch to too many switch hubs.
  • Page 1 1
  • Page 2 2

Sapido HF-3205 Quick setup guide

Sapido
Brand
Sapido
Model
HF-3205
Category
Networking
Type
Quick setup guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents