Datalogic DS8100A Reference guide

DS8100A

Reference Manual

Datalogic Automation S.r.l.

Via S. Vitalino 13

40012 - Lippo di Calderara di Reno

Bologna - Italy

DS8100A Reference Manual

Ed.: 03/2010

extent under U.S. and international laws. Copying, or altering of this document is prohibited without

express written consent from Datalogic Automation S.r.l.

Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries,

including the U.S.A. and the E.U.

Genius, PackTrack, ACR, ASTRA, CD SQUARE and ID-NET are trademarks of Datalogic Automation

S.r.l. All other brand and product names mentioned herein are for identification purposes only and may

be trademarks or registered trademarks of their respective owners.

Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor for

incidental or consequential damages resulting from the use of this material.

23/03/10

iii

CONTENTS

REFERENCES ............................................................................................................vi

Reference Documentation........................................................................................... vi

Services and Support .................................................................................................. vi

Patents......................................................................................................................... vi

COMPLIANCE............................................................................................................vii

Electrical Safety...........................................................................................................vii

Laser Safety.................................................................................................................vii

Power Supply..............................................................................................................viii

CE Compliance...........................................................................................................viii

FCC Compliance ......................................................................................................... ix

GENERAL VIEW..........................................................................................................x

GUIDE TO INSTALLATION .......................................................................................xii

Point-to-Point Installation.............................................................................................xii

Master/Slave Lonworks Installation ............................................................................xiii

1 INTRODUCTION ..........................................................................................................1

1.1 Product Description ......................................................................................................1

1.2 Applications ..................................................................................................................1

1.3 Model Description.........................................................................................................3

1.3.1 Oscillating Mirror Models ..............................................................................................3

1.4 Indicators ......................................................................................................................4

1.5 Keypad and Display......................................................................................................4

1.5.1 Internal Net ...................................................................................................................5

1.5.2 Test Mode.....................................................................................................................5

1.6 Accessories ..................................................................................................................6

2 INSTALLATION ...........................................................................................................8

2.1 Package Contents ........................................................................................................8

2.2 Mechanical Mounting....................................................................................................9

2.2.1 Mounting the Scanner...................................................................................................9

2.2.2 Mounting the Scanner with Accessories.....................................................................10

2.3 Positioning the Scanner..............................................................................................12

3 CBX ELECTRICAL CONNECTIONS.........................................................................13

3.1 Power Supply..............................................................................................................15

3.2 Main Serial Interface...................................................................................................15

3.2.1 RS232 Interface..........................................................................................................16

3.2.2 RS485 Full-Duplex Interface.......................................................................................17

3.2.3 RS485 Half-Duplex Interface......................................................................................18

3.3 Auxiliary RS232 Interface ...........................................................................................20

3.4 Inputs..........................................................................................................................21

3.4.1 Code Verifier...............................................................................................................25

3.5 Outputs .......................................................................................................................25

3.6 User Interface - Host...................................................................................................28

4 CUSTOM CABLE ELECTRICAL CONNECTIONS ...................................................29

4.1 Power Supply..............................................................................................................31

4.2 Main Serial Interface...................................................................................................31

iv

4.2.1

RS232 Interface..........................................................................................................32

4.2.2 RS485 Full-Duplex Interface.......................................................................................33

4.2.3 RS485 Half-Duplex Interface......................................................................................34

4.3 Auxiliary Interface .......................................................................................................36

4.4 Inputs..........................................................................................................................36

4.4.1 Code Verifier...............................................................................................................39

4.5 Outputs .......................................................................................................................39

4.6 User Interface .............................................................................................................41

5 LONWORKS CONNECTIONS...................................................................................42

5.1 Network Termination...................................................................................................43

5.2 Lonworks Interface .....................................................................................................44

6 FIELDBUS CONNECTIONS ......................................................................................46

6.1 Ethernet Interface .......................................................................................................46

7 TYPICAL LAYOUTS ..................................................................................................48

7.1 Local Lonworks Network.............................................................................................48

7.1.1 Small Synchronized Network......................................................................................49

7.1.2 Large Synchronized Network......................................................................................51

7.1.3 Redundant System .....................................................................................................53

7.1.4 Multidata Network.......................................................................................................55

7.1.5 Fieldbus Networks ......................................................................................................56

8 SOFTWARE CONFIGURATION................................................................................58

8.1 Genius™ Installation...................................................................................................58

8.2 Guide to Rapid Configuration .....................................................................................58

8.2.1 Wizard for Quick Reader Setup..................................................................................58

8.2.2 Genius™ Network Setup Through Master..................................................................61

8.2.3 Alternative Slave Address Assignment.......................................................................66

8.3 Advanced Genius™ Configuration .............................................................................66

8.3.1 Genius™ Shortcuts for Network Configuration...........................................................67

8.4 Parameter Default Values...........................................................................................69

9 READING FEATURES...............................................................................................73

9.1 Advanced Code Reconstruction (ACR™ 4)................................................................73

9.1.1 Tilt Angle for Advanced Code Reconstruction............................................................73

9.2 PackTrack™ ...............................................................................................................74

9.2.1 PackTrack™ Calibration for DS8100A .......................................................................76

9.2.2 PackTrack™ Calibration for DS8100A Oscillating Mirror Models...............................78

9.3 Performance ...............................................................................................................78

9.3.1 Reading Conditions ....................................................................................................78

9.4 Reading Diagrams......................................................................................................80

10 MAINTENANCE .........................................................................................................90

10.1 Cleaning......................................................................................................................90

10.2 CBX/SC4000 Backup & Restore ................................................................................90

10.3 Automatic Scanner Replacement (ASR) ....................................................................90

10.3.1 ASR Network Configuration........................................................................................91

10.3.2 Scanner Replacement Procedure...............................................................................91

11 TROUBLESHOOTING ...............................................................................................92

12 TECHNICAL FEATURES...........................................................................................95

v

A

ALTERNATIVE LAYOUTS ........................................................................................97

Point-to-Point..............................................................................................................97

ID-NET™ Gateway.....................................................................................................99

Pass Through ...........................................................................................................100

RS232 Master/Slave.................................................................................................101

Multiplexer ................................................................................................................103

GLOSSARY..............................................................................................................104

INDEX.......................................................................................................................107

vi

REFERENCES

REFERENCE DOCUMENTATION

The documentation related to the DS8100A management is listed below:

 PWR series power supply unit Installation Manuals

 SC6000 Controller Reference Manual

 PWO power supply unit Installation Manual

 GFC-80 90° deflecting mirror

 GFC-800 90° deg. mirror close distance

 CBX100/500 Installation Manuals

 Document about the Ethernet connectivity

 Help On-Line in PDF format

SERVICES AND SUPPORT

Datalogic provides several services as well as technical support through its website. Log on

to www.automation.datalogic.com and click on the links

indicated for further information:

 PRODUCTS

Search through the links to arrive at your product page which describes specific Info,

Features, Applications, Models, Accessories, and Downloads including the Genius™

utility program, which allows device configuration using a PC. It provides RS232 and

Ethernet interface configuration.

 SERVICE

- Overview

- Warranty Extensions and Maintenance Agreements

- Sales Network

- Listing of Subsidiaries, Repair Centers, Partners

- Helpdesk

- Material Return Authorization

PATENTS

This product is covered by one or more of the following patents:

U.S. patents: Re. 36,251; 5,483,051; 5,992,740; 6,347,740 B1; 6,177,979 B1; 6,394,352 B1;

6,443,360 B1; 6,527,184 B1; 6,629,639 B2; 6,688,524 B1; 6,742,710 B2; 7,161,685 B1;

5,028,772; 5,124,538; 5,466,921; 5,548,107; 6,206,289 B1; 6,669,091 B2; 7,000,838 B2.

European patents: 652,530 B1; 789,315 B1; 851,376 B1; 926,615 B1; 959,426 B9;

1,096,416 B1; 1,217,571 B1; 1,363,228 B1; 1,607,901 B1.

Japanese patents: 3,793,585; 4,033,958; 4,376,353.

Additional patents pending.

vii

COMPLIANCE

ELECTRICAL SAFETY

This product conforms to the applicable requirements contained in the European Standard for

electrical safety EN-60950 at the date of manufacture.

WARNING

This symbol refers to operations that must be performed by qualified

personnel only. Example: opening the device.

WARNING

This symbol refers to operations where there is danger of electrical

shock. Before opening the device make sure the power cable is

disconnected to avoid electric shock.

LASER SAFETY

The following information is provided to comply with the rules imposed by international

authorities and refers to the correct use of the DS8100A scanner.

Standard Regulations

This scanner utilizes up to 4 low-power laser diodes. Although staring directly at the laser

beam momentarily causes no known biological damage, avoid staring at the beam as one

would with any very strong light source, such as the sun.

Avoid that the laser beam hits the eye of an observer, even through reflective surfaces such

as mirrors, etc.

This product conforms to the applicable requirements of both EN60825-1 and

CDRH 21 CFR1040 at the date of manufacture. The reader is classified as a Class 2 laser

product according to EN60825-1 regulations and as a Class II laser product according to

CDRH regulations.

There is a safety device which allows the laser to be switched on only if the motor is rotating

above the threshold for its correct scanning speed.

WARNING

Use of controls or adjustments or performance of procedures other than those

specified herein may result in exposure to hazardous visible laser light.

The laser light is visible to the human eye and is emitted from the window on the side of the

scanner (Figure A).

viii

Warning labels indicating exposure to laser light and the device classification are applied

onto the body of the scanner (Figure A):

AVOID EXPOSURE

LASER LIGHT IS EMITTED

FROM THIS APERTURE

CAUTION-CLASS 3B

LASER LIGHT

WHEN OPEN

AVOID

EXPOSURE TO BEAM

Model No. Amp.

Serial No.

DATALOGIC S.P.A. Via Candini, 2

40012 Calderara di Reno - Bologna - Italy

Manufactured Volt

This product conforms to the applicable requirements

of 21CFR1040 at the date of manufacture.

LASER LIGHT

DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

MAXIMUM OUTPUT RADIATION 1 mW

EMITTED WAVELENGTH 630~680 nm

TO EN 60825-1:2001

Warning and Device Class Labels

Disconnect the power supply when opening the device during maintenance or installation to

avoid exposure to hazardous laser light.

The laser diodes used in this device are classified as Class 3B laser products according to EN

60825-1 regulations and as Class IIIb laser products according to CDRH regulations. Any

violation of the optic parts in particular can cause radiation up to the maximum level of the

laser diode (30 mW at 630~680 nm).

POWER SUPPLY

This product is intended to be installed by Qualified Personnel only.

- This scanner is intended to be supplied by either a UL Listed power supply marked 'Class

2' or 'LPS', output rated 20 – 30 V dc , minimum 1.5 A or by a UL Listed computer with

LPS outputs.

- This scanner must be supplied by a Class II Power Supply Unit conforming to the

EN 60950 safety regulation.

CE COMPLIANCE

Warning:

This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

ix

FCC COMPLIANCE

Modifications or changes to this equipment without the expressed written approval of

Datalogic could void the authority to use the equipment.

This device complies with PART 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference which may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

x

GENERAL VIEW

DS8100A-XXX0

Figure A – DS8100A

Laser Beam Output Window

Laser Safety Label

Product Label

Warning and Device Class Label

1

2

3

4

Connector Panel

Display

Service Access Cap

5

6

7

Mounting Holes

8

DS8100A-XXX5

Figure B – DS8100A Oscillating Mirror Models

Laser Beam Output Window

1

Laser Safety Label

2

1

2

1

2

8

5

3

4

6

7

xi

Figure C – Display and Keypad Panel

Programming Keypad

Power On LED (Green)

Phase On LED

(

Yellow

)

Encoder LED (Yellow)

1

2

3

4

TX Data LED (Green)

Network LED (Red)

LCD Display

5

6

7

Figure D – Connector Panel for Standard Models

Lonworks 17-pin male connector

Lonworks 17-pin female connector

1

2

Serial interface and I/O 26-pin connector

3

Figure E – Connector Panel for Ethernet Models

Lonworks 17-pin male connector

Lonworks 17-pin female connector

Harting RJ industrial connector

1

2

4

Serial interface and I/O 26-pin connector

3

1

2

3

1

2

4

3

7

1

2 3

4 5 6

xii

GUIDE TO INSTALLATION

POINT-TO-POINT INSTALLATION

The following can be used as a checklist to verify all the necessary steps to complete

installation of the DS8100A scanner.

1) Read all information in the section “Safety Regulations” at the beginning of this manual.

2) Correctly mount the scanner according to the information in par. 2.2 and position it at the

correct reading distance

as shown in par. 2.3 and par. 9.4.

3)

Make electrical connections to your DS8100A scanner by:

a) Connecting the DS8100A scanner to the CBX connection box by means of one of the

CAB-F0x cables provided as accessory (see par. 1.6).

b)

Providing correct and complete system cabling through the CBX connection box

according to the signals necessary for the layout of your application (trigger, inputs,

outputs).

 Cabling: Power, Interface, Inputs, Outputs, etc. For further details, see chapter 3

(chapter 4 for custom cabling).

 Alternative Layouts: Point-to-Point, Pass Through, RS232 Master/Slave,

Mutliplexer. See appendix A for layout references.

4)

Configure the DS8100A scanner by installing and running the Genius™ configuration

program from the CD-ROM provided. See chapter 8 and the Help On-Line for details.

The main steps are:

 Select the codes to be read

 Set-up the communication parameters

 When PackTrack™ is required, perform PackTrack™ calibration

 Define data formatting parameters

NOTE

Fine tuning of the scanner position for barcode reading can be

accomplished by performing a test through the SPY configuration tool in

Genius™.

5) Exit the configuration program and run your application.

The installation is now complete.

xiii

MASTER/SLAVE LONWORKS INSTALLATION

The following can be used as a checklist to verify all the steps necessary to complete

installation of the DS8100A scanner in a Master/Slave Lonworks network.

1) Read all information in the section “Safety Regulations” at the beginning of this manual.

2) Correctly mount the scanner according to the information in par. 2.2 and position it at the

correct reading distance

as shown in par. 2.3 and par. 9.4.

3)

Make electrical connections to your DS8100A scanner by:

a) Connecting the DS8100A Master

scanner to the CBX100 by means of one of the

CAB-F0x cables provided as accessory (see par. 1.6).

b)

Correctly terminating the DS8100A Master reader according to the information given

in par. 5.1 and par. 7.1.

c)

Completing the system wiring adding as many slave scanners as required by your

system layout (refer to par. 7.1).

d)

Correctly providing bus return to the last DS8100A Slave reader of the network

according to the information given in par. 5.1 and par. 7.1.

4)

Install and run the Genius™ configuration program from the CD-ROM provided.

Configure the Local Lonworks Network using one of the procedures given below

:

 Configure the entire network through the Master as described in par. 8.2.2;



Configure the Master as described in par. 8.2.2 and locally define each slave scanner

address as

described in par. 8.2.3.



Define each scanner, master and slaves (with their addresses), by using the scanner

keypad according to the information given in par. 1.5.1.

5)

Configure the Master scanner through the Genius™ program. See chapter 8 and the

Help On-Line for details.

The main steps are:

 Select the codes to be read

 Set-up the communication parameters

 When PackTrack™ is required, perform PackTrack™ calibration, see par. 9.2.1.

 Define data formatting parameters

6) Configure each Slave scanner through the Master scanner using Genius™. See chapter

8 and the Help On-Line for details. The main steps are:

 Select the codes to be read

 When PackTrack™ is required, perform PackTrack™ calibration, see par. 9.2.1.

NOTE

Fine tuning of the scanner position for barcode reading can be

accomplished by performing a test through the SPY configuration tool in

Genius™.

xiv

7) Send the configuration to the Master.

8) Perform the CBX/SC4000 Backup procedure for system backup purposes (see par.

10.2). For backward compatibility you can perform the ASR Network Configuration

procedure f

or system backup purposes (see par. 10.3.1).

9)

Exit the configuration program and run your application.

The installation is now complete.

INTRODUCTION

1

1 INTRODUCTION

1.1 PRODUCT DESCRIPTION

The DS8100A scanner is a barcode reader complete with decoder designed to provide an

innovative and high performance solution in omnidirectional reading applications by

combining the following advanced technologies with Datalogic solid experience in the

material handling sector.

Some of the main features of DS8100A are listed below:

 scanning speed 1000 scans/sec.

 reads all popular codes.

 supply voltage from 20 to 30 Vdc.

 test mode to verify the reading features and exact positioning of the scanner without the

need for external tools.

 programmable in several different operating modes to suit the most various barcode

reading system requirements.

 light source: solid state laser diodes; the light emitted has a wave length between

630~680 nm. For laser safety precautions refer to the “Compliance” section at the

beginning of this manual.

1.2 APPLICATIONS

The DS8100A barcode reader is specifically designed for industrial applications and for all

cases requiring high reading performance such as:

 code reconstruction

 reading of codes covered by plastic film

 reading of codes with a wide depth of field

 reading of high resolution codes positioned at long distances from the reader

 code reading on fast moving objects.

DS8100A is designed for both single-reader layouts and multi-reader layouts. For typical

layouts see chapter 7 and appendix A.

DS8100A REFERENCE MANUAL

2

1

Feature

Benefit

ACR™

 Advanced Code Reconstruction technology

allows the reading of low aspect ratio labels

placed anywhere on a parcel and enhances the

readability of poorly printed or damaged codes.

CD SQUARE™

 CD SQUARE™ provides useful information on

label position and object shape elaborated during

the barcode reading phase. This innovative

technology identifies the area in which the code is

located and measures the code distance from the

scanner.

PACKTRACK™

 PackTrack™ is a Datalogic patented parcel

tracking system which improves the reading

features in omnidirectional stations. In particular,

PackTrack™ manages 6-sided reading systems

when it is impossible to detect the real position of

the code on the parcel, thus overcoming the need

for external accessories essential in traditional

tracking systems.

ASTRA™

 Automatically SwiTched Reading Area™ is the

new Datalogic technology based on a multi-laser

architecture and a fixed mounted optic system

which concentrates the multiple laser emissions in

a single laser beam. As each laser emitter is

focused on a specific range of the reading area, a

sophisticated electronic controller selects the best

focused laser emitter with respect to the code to

read. This allows the reading of medium-high

density codes in a large reading area on very fast

conveyors.

Flexibility

 The high frequency laser diode modulation

system guarantees complete immunity to ambient

light and allows installation of the DS8100A in any

working area.

Reading parcels on conveyors

 As a result of the ASTRA™ multiple laser

technology, DS8100A gives a great real time DOF

even on high speed conveyors. Furthermore,

DS8100A implements the Packtrack™

functionality which leads to an increase of the

plant production as a result of the augmented

system throughput.

Master working as a

Multiplexer on high speed

Lonworks bus

 Great competitiveness of the offer, since the cost

of an external multiplexer is saved;

 High data transfer on an industrial, reliable bus

running at 1.25 Mbit/sec.

Genius™ Configurator SW

 Reduced learning time, with an easy wizard

approach;

 Multilanguage platform;

 All the configuration parameters stored in the

scanner;

 Not dependent on the Physical interface.

INTRODUCTION

3

1

1.3 MODEL DESCRIPTION

The DS8100A scanner is available in versions that differ depending on the interface

connection, the optical resolution and on the optic version:

DS8100A - X X X X

O

p

tic Version:

0 = Linear

O

p

tical Resolution:

0 = Low resolution

1 = Medium resolution

Communication Type:

0 = Standard version

1 = Ethernet version

2 = High resolution

3 = Very High resolution

5 = Oscillating mirror

Laser Number:

2 = Double laser

3 = Tri

p

le laser

1.3.1 Oscillating Mirror Models

Oscillating mirror models are used when coverage of a large reading area is required, mainly

in picket fence applications.

The oscillating mirror is placed in front of the reading aperture of the DS8100A scanner to

deflect the laser beam. As the mirror moves, this sweeping function of the laser beam allows

the coverage of a larger area to locate the barcodes. The code can also be reconstructed as

the beam sweeps over it.

The aperture angle is symmetrical and the scan line perpendicular to the scanner is at 0° as

shown in the figure below.

0°

+25°

-25°

Figure 1- Oscillating Mirror Reference Angle

By configuring the oscillating speed up to the maximum value of 19 Hz, raster emulation can

be performed for reading fast moving objects.

Hz Max. Aperture

0-5 50°

6-10 30°

11-15 20°

16-19 10°

DS8100A REFERENCE MANUAL

4

1

NOTE

By limiting the raster width to the minimum necessary, the number of scans

on the reading surface is increased.

The oscillating mirror is completely controlled by software commands and therefore avoids

complex mechanical calibrations. For details of the software configuration parameters see

the Genius™ Help On Line.

1.4 INDICATORS

The DS8100A has five LEDs on the rear panel. The indicators have the following functions:

POWER ON

(green) Indicates the scanner is turned on.

PHASE ON

(yellow) Indicates the external presence sensor is active.

ENCODER

(yellow) Indicates the external encoder signal is active.

TX DATA

(green) Indicates data transmission both on the main and on the auxiliary

interface.

NETWORK

(red) Indicates the Lonworks network is functioning correctly. This LED is

normally ON.

1.5 KEYPAD AND DISPLAY

The DS8100A keypad allows entering a menu for selection of one of the following functions:

 Welcome: shows the current software release and operating mode;

 Autolearn: starts the procedure making it possible to obtain an automatic, accurate

and fast configuration of DS8100A without the necessity of directly

checking/modifying the relevant parameters;

 Internal Net: defines scanner function within the network (see below);

 Ethernet Mode: allows setting the scanner IP address to be used within the network;

 LCD Contrast: sets the LCD contrast ;

 Bus: not used for DS8100A scanners;

 Test Mode: allows verifying the scanner reading position and features (see below).

The same settings may be performed by using the Genius™ program (see chapter 8 for

details).

INTRODUCTION

5

1

1.5.1 Internal Net

This submenu can be used as an alternative to configuration through Genius™, to assign the

DS8100A scanner within a master/slave network.

It allows defining the scanner function (slave/master) within the network and, if configured as

Slave, its address.

To enter the Internal Net submenu and configure the scanner follow the given procedure:

1) Press and hold both the ▲ (up arrow) and ▼ (down arrow) keys for about 2 seconds to

enter the Main menu;

2) Use the ▲ (up arrow) or ▼ (down arrow) key to select the “Internal Net” item, then press

the ENT (enter) key to confirm;

3) Use the ▲ (up arrow) or ▼ (down arrow) key to select the “LonWAddrSel”” item, then

press the ENT (enter) key to confirm;

4) Use the ▲ (up arrow) or ▼ (down arrow) key to select your scanner function among

“Master”, “Slave n”, “Slave jolly”, “Disabled”; then, press the ENT (enter) key to confirm;

5) Use the ▲ (up arrow) or ▼ (down arrow) key to select the “Exit” item, then press the ENT

(enter) key to confirm. Repeat this step again to exit the Main Menu and return to the

scanner current operating mode.

1.5.2 Test Mode

Test Mode is particularly advised during the installation phase, since it causes the reader to

be continuously activated allowing verification of its reading features and its reading position

with respect to the barcode.

To enter the Test Mode submenu and configure the scanner follow the given procedure:

1) Press and hold both the ▲ (up arrow) and ▼ (down arrow) keys for about 2 seconds to

enter the Main menu.

2) Use the ▲ (up arrow) or ▼ (down arrow) key to select the “Test Mode” item, then press

the ENT (enter) key to confirm. The reader enters Test Mode.

3) Press the ▲ (up arrow) key to exit the Test Mode.

4) Use the ▲ (up arrow) and ▼ (down arrow) key to select the “Exit” item, then press the

ENT (enter) key to confirm. The scanner exits the Main Menu and returns to its current

operating mode.

DS8100A REFERENCE MANUAL

6

1

1.6 ACCESSORIES

The following accessories are available on request for DS8100A:

Name Description Part Number

Power Supplies

PWR-120 J-box power unit 110/230 VAC 24 V 120 W 93ACC1530

PWR-240 J-box power unit 110/230 VAC 24 V 240 W 93ACC1070

PWR-480A J-box power unit 110/230 VAC 24 V 480 W 93ACC1850

Cables and Terminators

BTK-8100 Bus terminator kit (5 pcs) 93ACC1090

BTK-8102 Double terminator kit (2 pcs) 93A051287

CAB-8100 10 wire shielded cable D 9.5 mm – 50 m 93ACC1120

CAB-8101 17-pin scanner/scanner connection cable 1.2 m 93A051020

CAB-8102 17-pin scanner/scanner connection cable 2.5 m 93A051030

CAB-8105 17-pin scanner/scanner connection cable 5 m 93A051040

CAB-8305 Power and bus return cable (last Slave) 5 m 93A051268

CAB-8310 Power and bus return cable (last Slave) 10 m 93A051336

CAB-8402 No power cable 2.5 m 93ACC1758

CAB-8405 No power cable 5 m 93ACC1759

CAB-F01 6K-8K FBUS cable to CBX 1 m 93A051355

CAB-F02 6K-8K FBUS cable to CBX 2 m 93A051356

CAB-F05 6K-8K FBUS cable to CBX 5 m 93A051357

CAB-6502 Fam 6K-8K cross cable 2.5 m 93A051288

CAB-6505 Fam 6K-8K cross cable 5 m 93A051289

CAB-8605 Power and Lonworks termination cable (Master) 5 m 93A051290

Software Management

Datalogic WebSentinel-005 Supervisor (up to 5 arrays) 93A101014

Datalogic WebSentinel-010 Supervisor (up to 10 arrays) 93A101015

Datalogic WebSentinel-020 Supervisor (up to 20 arrays) 93A101016

Datalogic WebSentinel-032 Supervisor (up to 32 arrays) 93A101017

Datalogic WebSentinel-064 Supervisor (up to 64 arrays) 93A101018

Datalogic WebSentinel-128 Supervisor (up to 128 arrays) 93A101019

Datalogic WebSentinel-256 Supervisor (up to 256 arrays) 93A101020

Mirrors

GFC-80 90° mirror 93A251020

GFC-800 90° mirror close distance 93A201103

* Connection Boxes

CBX100 Compact Connection Box 93A301067

CBX500 Modular Connection Box 93A301068

CBX800 Gateway Connection Box 93A301077

BM100 Backup Module 93ACC1808

BA100 DIN Rail Adapters for CBX 93ACC1821

BA200 Bosch Adapters for CBX 93ACC1822

BA900 Two Cable Glands Panel 93ACC1847

Sensors

MEP-593 Photocell kit – PNP (PH-1) 93ACC1791

MEP-543 Photocell kit – NPN 93ACC1728

OEK-2 Optical encoder (10 m cable + spring) 93ACC1770

OEK-1 Optical encoder kit + 10 m cable 93ACC1600

* DS8100A application software does not support any of the CBX500 Host Interface Module accessories nor the

BM150 Display accessory. Use the CBX800 Gateway for Host Interface Applications, (Fieldbus and non

Fieldbus).

Page is loading ...

Datalogic DS8100A Reference guide

Datalogic DS8100A Reference guide

Related papers

Other documents