Page is loading ...
32'-0"
9.75
25'-0"
7.62
FRONT VIEW
NET NOT SHOWN FOR CLARITY
ISOMETRIC VIEW
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 1 of 29
753100CXX - DOUBLE RING THROWING CAGE
GROUND SLEEVE AND NET ANCHOR FOOTINGS LOCATION
Copyright
2023 by Gill Athletics.
All rights reserved.
25'-0"
7.62
43'-10
3
4
"
13.38
29'-4"
8.94
R11'-5
3
4
"
3.50
R11'-5
3
4
"
3.50
20'-5
1
2
"
6.23
20'1
1
4
"
6.13
7'10
1
2
"
2.40
14'4
3
4
"
4.39
TOP VIEW
21'-8"
6.60
32'-0"
9.75
SIDE VIEW
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 2 of 29
753100CXX - DOUBLE RING THROWING CAGE
GROUND SLEEVE AND NET ANCHOR FOOTINGS LOCATION
Copyright
2023 by Gill Athletics.
All rights reserved.
BACK OF
UPRIGHT
FRONT OF
UPRIGHT
FRONT OF
UPRIGHT
BACK OF
UPRIGHT
SPLICE
TIGHTEN TOP
AND BOTTOM
BOLT AT BACK
OF UPRIGHT
SPLICE FIRST
TIGHTEN TOP
AND BOTTOM
BOLT AT BACK
OF UPRIGHT
SPLICE FIRST
INSTALL UPRIGHT ASSEMBLY STEPS
INSTALL ALL UPRIGHT SPLICE HARDWARE LOOSELY
STAND UPRIGHTS UP INSIDE GROUND SLEEVES.
TIGHTEN TOP AND BOTTOM BOLTS AT BACK OF UPRIGHT
SPLICE FIRST. THIS PULLS THE SPLICE TO THE BACK OF
THE UPRIGHT INSIDE WALL ENSURING THE ASSEMBLY TO
BE MORE STRAIGHT.
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 3 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
ALL THREAD; 3/4"-10 X 9.5"
HEX NUT; 3/4"-10
GG
ASSEMBLE ALL THREE UPRIGHTS ON THE GROUND BEFORE
STANDING THEM UP INSIDE THE GROUND SLEEVES.
HEX BOLT; 3/4"-10 X 10"
HEX BOLT; 3/4"-10 X 2"
LOCK WASHER; 3/4"; ZINC; SPLIT RING
FLAT WASHER; 3/4"
HEX NUT; 3/4"-10
FLAT WASHER; 3/4"
UPRIGHT SPLICE
LOCK WASHER; 3/4"; ZINC; SPLIT RING
FLAT WASHER; 3/4"
UPRIGHT ASSEMBLY
INSTALL ALL THREADS INTO BOTTOM OF
LOWER UPRIGHT TUBE.
CENTER ALL THREADS AS SHOWN BELOW.
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 4 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
VINYL COVER
ROTATE VINYL COVER SO THAT THE
GRAPHICS OR GILL LOGO FACES THE FRONT
VIEW OF THE CAGE
WRAP FOAM SHEET AROUND THE
TWO
FRONT UPRIGHTS
TO COVER THE SPLICE
HARDWARE.USE THREE 36" STRIPS OF
DOUBLE SIDED VELCRO TO SECURE THE
FOAM IN PLACE.
FOAM SHEET 1" THICK
36" VELCRO STRIP
SURROUND FOAM WITH THE VINYL COVER.
PULL AS TIGHT AS POSSIBLE WHILE
ALLIGNING THE VELCRO ON THE VINYL.
NOTE THAT COVER SHOULD GO PAST THE
FOAM BY 1" ON EACH SIDE.
UPRIGHT PAD INSTALL
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 5 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
1/2" FLAT WASHER
1/2" FLAT WASHER
1/2" NYLOCK NUT
1/2" X 1.25" BOLT (INSTALL
THROUGH HOLE, NOT SLOT)
FRONT UPRIGHT
PULLEY SHOWN
TOP PULLEY INSTALL
FRONT UPRIGHTS
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 6 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
1/2" NYLOCK NUT
1/2" FLAT WASHER
See next page for
pulley allignment.
NO PAD
NEEDED AT
REAR UPRIGHT.
REAR UPRIGHT
PULLEYS SHOWN
1/2" FLAT WASHER
1/2" X 1.25" BOLT
(INSTALL THROUGH
HOLES, NOT SLOT)
ORIENTATE REAR
PULLEYS AS SHOWN
TOP PULLEY INSTALL
REAR UPRIGHT
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 7 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
TOP PULLEY LAYOUT
ALIGN OUTER RIGHT
PULLEY ON REAR UPRIGHT
WITH PULLEY ON RIGHT
FRONT UPRIGHT.
ALIGN OUTER LEFT
PULLEY ON REAR
UPRIGHT WITH PULLEY
ON LEFT FRONT
UPRIGHT.
See next page for
cable routing.
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 8 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
TIGHTEN BOLTS AT GROUND
SLEEVES TO TRUE UPRIGHT.
UPRIGHT INSTALL
INSTALLER NOTE:
DROP FULLY ASSEMBLED UPRIGHTS INTO
GROUND SLEEVES AND ALIGN AS SHOWN.
BE SURE TO NOT SCRATCH UP THE POWDER
COAT OF THE UPRIGHTS.
IF NO LIFT IS AVAILABLE TO REACH THE TOP OF
THE UPRIGHTS TO FEED 1/4" CABLE THROUGH
TOP PULLEYS, DO SO BEFORE STANDING UP
THE UPRIGHTS.
ONCE UPRIGHTS ARE IN PLACE, PLUMB AND
ALIGN THEM. TIGHTEN BOTTOM BOLTS AT THE
GROUND SLEEVE TO KEEP UPRIGHTS FROM
ROTATING.
See next page for
upright alignment.
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 9 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
45 45
28'2"
REAR UPRIGHT
CAGE CENTER LINE
INSTALLER NOTE:
ONCE UPRIGHTS ARE IN PLACE, PLUMB THEM
AND TIGHTEN BOTTOM BOLTS AT THE GROUND
SLEEVE TO KEEP UPRIGHTS FROM ROTATING.
UPRIGHT ALIGNMENT
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 10 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
3'4" STRAIGHT
STRAIGHT HOOP SECTION
CURVED HOOP SECTION
HOOP SPLICE
ALUM CARD AT THIS END
1'0" STRAIGHT 1'0" STRAIGHT
HOOP SPLICE
CURVED HOOP SECTION CURVED HOOP SECTION
STRAIGHT HOOP SECTION
ALUM CARD AT THIS END
STRAIGHT HOOP SECTION
ALUM CARD AT THIS END
3'4" STRAIGHT
ALUM CARD AT THIS END
HOOP TUBE LAYOUT
CURVED HOOP SECTION
HOOP SPLICE
STRAIGHT HOOP SECTION
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 11 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
REAR SPLICE AREA
SIDE SPLICE AREA
SIDE SPLICE AREA
1/2"-13 X 3.5" HEX SCREW
HOOP SPLICE
1/2"-13 NYLOCK NUT
1/2"-13 X 3.5" HEX SCREW
1/2" FLAT WASHER
SIDE SPLICE AREA
1/2" FLAT WASHER
1/2" FLAT WASHER
1/2" FLAT WASHER
1/2"-13 X 4" EYE BOLT
1/2"-13 NYLOCK NUT
REAR SPLICE AREA
HOOP ASSEMBLY
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 12 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
DOOR BEAM ASSEMBLY
DOOR BEAM SPLICE
1/2"-13 X 7 1/2" HEX SCREW
1/2" FLAT WASHER
1/2"-13 NYLOCK NUT
HOOP BRACKET
HOLES AT THIS END.
HOOP BRACKET
HOLES AT THIS END.
DOOR BEAM ASSEMBLY
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 13 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
1/2"-13 NYLOCK NUT
1/2"-13 X 3-1/2"
CARRIAGE BOLT
LEFT OUTER
BRACKET
1/2" FLAT
WASHER
RIGHT
INNER
BRACKET
1/2" FLAT
WASHER
RIGHT
INNER
BRACKET
1/2"-13 NYLOCK NUT
1/2"-13 X 3-1/2"
CARRIAGE BOLT
RIGHT OUTER
BRACKET
DOOR BEAM ASSEMBLY
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 14 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
1/2" FLAT WASHER
1/2"-13 X 4-1/2" HEX BOLT
1/2" FLAT WASHER
1/2"-13 NYLOCK NUT
USE WOODEN BLOCKING TO PROP HOOP
AND BEAM ASSEMBLY OFF THE GROUND.
ASSEMBLE HOOP TO BEAM
INSIDE THE THREE UPRIGHTS.
1/2"-13 NYLOCK NUT
1/2" FLAT WASHER
1/2"-13 X 4-1/2"
HEX BOLT
HOOP TO BEAM ASSEMBLY
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 15 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
DOOR NET TRACK
SELF DRILLING SCREW; #12 X 1"
SELF DRILLING SCREW; #12 X 1"
111
2
"
REF.
DOOR NET TRACK
SELF DRILLING
SCREW; #12 X 1"
111
2
"
REF.
DOOR NET TRACK
DOOR TRACK INSTALL
BRACKET END FACE
FLUSH WITH INSIDE
BEAM FACE.
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 16 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
1/4" PHILLIPS FLAT SCREW HEAD
TRACK SPLICE
CURVED TRACK
1/4" FLAT
WASHER
1/4" NYLOCK
NUT
DRILL
3
8
"
CURVED
TRACK
BUTT CURVED
TRACK AGAINST
STRAIGHT TRACK
AND MARK HOLE
LOCATIONS ON
CURVED TRACK.
PRE-DRILL 3/8"
HOLE INTO
CURVED TRACK.
DOOR NET TRACK
TRACK
SPLICE
DOOR TRACK INSTALL
SLIDE TRACK SPLICE HALF WAY
ONTO DOOR NET TRACK (AT SIDE
BY THE HOOP BRACKET). THIS
SPLICE IS A TIGHT FIT.
REPEAT TRACK SPLICE
AND CURVED TRACK
INSTALL STEPS ON
OPPOSITE SIDE.
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 17 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
RIGHT SIDE
MAGNET
8'9
1
2
"
END OF DOOR BEAM TO INSIDE FACE OF MAGNET FLAT
SELF DRILLING SCREW; #12 X 1"
LEFT HAND MAGNET FLAT ASSEMBLY
RIGHT SIDE SHOWN
AFTER SPLICE IS IN PLACE, REMOVE SET SCREWS
AND DRILL 1/4" HOLE FOR SET SCREW TO NEST IN.
BE SURE TO NOT DAMAGE THE THREADS.
LEFT SIDE
MAGNET
90.00°
RIGHT SIDE
MAGNET
MAGNET AT TOP
OF BRACKET
105 1/2"
TO END OF DOOR BEAM
90.00°
105 1/2"
TO END OF DOOR BEAM
MAGNET AT TOP
OF BRACKET
MAGNET FLAT INSTALL
REPEAT TRACK SPLICE
AND CURVED TRACK
INSTALL STEPS ON
OPPOSITE SIDE.
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 18 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
48"
REF.
REAR UPRIGHT
8 5/8" U-BOLT WITH
RUBBER GASKET
WINCH
WINCH COVER
CLEVIS PIN
(1 AT EACH CORNER
OF WINCH COVER)
WINCH INSTALLATION
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 19 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
REAR
UPRIGHT
TO FRONT HOOP PICKUP
TO FRONT HOOP PICKUP
1/4"-20 SET SCREW
FEED THE CABLES BETWEEN THE BACK OF THE DRUMS AND THE WINCH
FRAME AND UP INTO THE LOWER HOLE OF THE CABLE OPENING. FEED
THE CABLE INTO THE OPENING UNTIL THE CABLE END IS JUST VISIBLE IN
THE UPPER HOLE. TIGHTEN THE SET SCREW SECURELY ONTO THE
CABLE. REPEAT THIS FOR EACH DRUM AND CABLE.
WINCH INSTALLATION
www.gillathletics.com
800-637-3090
9/8/2023
INST753100CXX
Page 20 of 29
753100CXX - DOUBLE RING THROWING CAGE
ASSEMBLY INSTRUCTIONS
Copright
C
All rights reserved.
2023
by Gill Athletics.
/
