2. Pet Gear
  3. PG9916DSG

Pet Gear PG9916DSG User manual

  • Hello! I've reviewed the instruction manual for the PET GEAR Designer Pet StRamp models PG9916DBG, PG9916DCH, PG9916DSG, and PG9916DTN. This manual provides guidance on assembling the pet ramp, including installing the riser, ramp and attaching left panel, also how to use the cover. I'm ready to answer your questions about the product and its proper use.
  • What should I do if any parts are missing?
    What is the purpose of this product?
    What should I do if inserting a part is difficult?
To see our full line of products, visit us online at: www.petgearinc.com
CUSTOMER SERVICE HELP DESK
[email protected]
Toll-Free 877-752-9123 - Eastern Standard Time 8am-3pm, Monday through Friday
For The ON-THE-GO Pet™
INSTRUCTION MANUAL
DESIGNER
PG9916DBG/PG9916DCH/PG9916DSG/PG9916DTN
AT
StR amp
DESIGNER STRAMP WITH REMOVABLE COVER • PG9916DBG/PG9916DCH/PG9916DSG/PG9916DTN
2
PARTS LIST
Check that you have all the parts shown BEFORE assembling your product.
If any parts are missing, call Customer Service.
B
B
C
F
F
E
D
D
A
C
E
A
G
G
G
BACK VIEW
OF PARTS
FRONT VIEW
OF PARTS
Riser
Dowel
Designer
Cover
Ramp
Top Stair
Left Panel Right Panel
H
DESIGNER STRAMP WITH REMOVABLE COVER • PG9916DBG/PG9916DCH/PG9916DSG/PG9916DTN 3
ASSEMBLY INSTRUCTIONS
Step 1. Place right panel on oor with
PET GEAR Logo facing the oor and
insert riser, lettered (B).
Make sure there are no gaps between
parts after inserting.
(If inserting part is difcult put a little dish
soap on doweled end before inserting.)
Step 2. Insert ramp, lettered (D).
Make sure there are no gaps between
parts after inserting.
Step 3. Insert top stair, lettered (F).
Make sure there are no gaps between
parts after inserting.
D
F
B
D
B
B
DESIGNER STRAMP WITH REMOVABLE COVER • PG9916DBG/PG9916DCH/PG9916DSG/PG9916DTN
4
ASSEMBLY INSTRUCTIONS
D
F
B
B
G
G
Step 4. Insert dowel, (G).
Make sure there are no gaps between
parts after inserting.
Step 5. Attach left panel.
Align all holes before pushing panel
down.
Make sure there are no gaps between
parts after inserting.
Stramp shown fully assembled.
DESIGNER STRAMP WITH REMOVABLE COVER • PG9916DBG/PG9916DCH/PG9916DSG/PG9916DTN 5
COVER INSTRUCTIONS
Step 1. Unfold the Designer
Cover, (H), and drape it over
the steps.
Pull the elastic strap over the
bottom of the StRamp.
Step 2. Pull the zipper down toward
the oor.
Step 3. Place carpet treads, (G), on top of the StRamp
and connect with Velcro strips.
Bottom View
StRamp shown
with cover on.
Elastic
Strap
H
HG
Velcro Strips
DESIGNER STRAMP WITH REMOVABLE COVER • PG9916DBG/PG9916DCH/PG9916DSG/PG9916DTN 6
WARNING!
FOR PETS ONLY.
Not intended to be used as a restraining device for aggressive or dangerous animals that dig, chew or paw
aggressively. Do not leave your pet unattended. PET GEAR is not liable for any damage caused by aggressive,
destructive, immature or untrained animals. Do not use near an open or exposed ame. Failure to follow these
warnings and the instructions could result in serious injury or death.
REPLACEMENT PARTS
Use only PET GEAR replacement parts.
Please have your model number ready before calling.
You can also request parts: http://www.petgearinc.com/main.asp?sel=2
PO Box 99∙West Rutland, VT∙05777∙877-752-9123∙www.petgearinc.com
/