KidKusion 6010 Installation guide

Brand: KidKusion

Model: 6010

Type: Installation guide

KidKusion 6010 is a hearth cushion designed to fit hearths up to 80" wide. It is made from a durable, non-toxic, flame-retardant foam rubber and can be cleaned with soap and water. Installation is easy and requires only a few simple tools. The cushion can be trimmed to fit smaller hearths and comes with double-sided attachment tape for secure installation. The KidKusion 6010 is a great way to add comfort and style to your fireplace.

Hearth Cushion

Fits up to 80” total across front of Hearth

Call 1-800-845-9236 if Hearth is longer than 80”.

INSTALLATION INSTRUCTIONS Model 6010/6020/6030

TOOLS NEEDED: Measuring Tape, Pencil, Straight Edge, Razor Knife, Rubbing Alcohol, Cloth, brush or vacuum cleaner

Step 1: Use brush or vacuum cleaner to remove any loose brick or mortar

particles. Clean hearth and underside of Hearth Cushion with rubbing alcohol.

Step 2: Place LH & RH Corners on hearth. If Corners are too deep

to fit on hearth, trim using Pad cutting instructions below. (Figure 2)

Step 3: Apply double sided attachment tape to LH & RH corners. Press firmly

on tape and then remove liner. Hold LH corner tight against the front and side

of hearth and press firmly on hearth. Repeat for RH corner. (Figure 2)

Step 4: Measure between LH and RH corners. Add 1/8” to measurement and

mark line on Center Connector with pencil. Cut Center Connector to length

using Pad cutting instructions. Place Center Connector on hearth and check fit.

(Figure 2)

Step 5: Place double sided attachment tape on hearth between the

LH & RH corners. Press firmly in place and remove liner. (Figure 2)

Step 6: Place left hand end of Center Connector next to LH Corner on hearth.

Make sure Center Connector is lined up with Corner. Press Center Connector

firmly against LH Corner and against front of hearth. Press Center Connector firmly

into place on hearth next to corner. Make sure to keep Center Connector pressed

against front of hearth and press it firmly into place along hearth. Be careful not to

stretch Center Connector as you attach it to hearth. (Figure 3)

Pad Cutting Instructions.

1) Place Pad on top of shipping box or some other flat surface so that when you cut through Pad, the knife will not damage your

floor or hearth below.

2) Lay straight edge on top of Pad and line it up with mark.

3) Using a sharp razor knife, hold it next to straight edge and cut through Pad using light to medium pressure. For best looking

cut, make multiple passes along straight edge until you have cut through Pad. DO NOT try to cut through the Pad in one or

two passes. Trying to cut pad in one pass may result in jagged cut.

Note: The Soft Seat Hearth Pad is made from a durable, CUSTOMER SERVICE: KidKusion, Inc., PO Box 1686

non-toxic, flame retardant foam rubber. Clean with Washington, NC 27889

soap and water. Phone: 1-800-845-9236

MATERIALS

INCLUDED

ITEM

QTY

DESCRIPTION

Right Hand Corner

Center Connector

Attachment Tape

Fig. 1

Step 5: Line tape up

with front edge of

hearth and press

firmly in place and

remove liner

Left Hand Corner

Step 4: Measure

distance between

RH & LH Corners

and add 1/8”

Step 3: Hold Pad

firmly against front

and side edge of hearth as

you lower it onto the hearth.

Step 3: Place

Double sided

attachment

tape on Corners.

Step 1: Clean Pad

with rubbing

alcohol prior to

applying tape.

Step 6:

Hold Pad

firmly against LH Corner,

front and side edge of hearth

as you lower it onto the

hearth.

Fig. 3

Fig. 2

Step 2: Trim to

length as needed

to fit hearth

Do Not Stretch Center

Connector while placing

hearth

KidKusion 6010 Installation guide

Brand: KidKusion

Model: 6010

Type: Installation guide

Download PDF

report

KidKusion 6010 Installation guide

KidKusion 6010 Installation guide

Related papers

Other documents