American Standard 0328008.222 User manual

0328008.222
American Standard
Brand
American Standard
Model
0328008.222
Type
User manual
J23
© 2017 AS America Inc.
spec_0328-Townsend Ped Sink 4/17
TOWNSEND
®
PEDESTAL SINK
FINE FIRECLAY
TOWNSEND
®
PEDESTAL SINK
❏ 0328.800 Faucet holes on 8" (203mm) centers (Illustrated)
❏ 0328.400 Faucet holes on 4" (102mm) centers
❏ 0328.100 Center hole only
•Finereclay
•Classicstyledrectangularpedestallavatory
•Rearoverow
•Suppliedwithmountingkit
•RightHeight
®
forgreatercomfortduringuse
•Faucetledgewithlargedeckarea(faucetnotincluded)
•Design coordinates with Townsend
®
Fixtures and Faucets
Nominal Dimensions:
30" x 19-1/2"
(762 x 495mm)
35-1/4"height
(895mm)
❏ 0328.008 Pedestal top-8" (203mm) centers
❏ 0328.004 Pedestal top-4" (102mm) centers
❏ 0328.001 Pedestal top-center hole only
❏ 0039.001 Pedestal only
Bowl sizes:
19" (485mm) wide,
12-3/4" (324mm) front to back,
5" (128mm) deep
Compliance Certications -
Meets or Exceeds the Following Specications:
•ASMEA112.19.2/CSAB45.1
To Be Specied:
❏ Color: ❏ White ❏ Linen
❏ Faucet Finish:
❏ Supplies:
❏ 1-1/4" Trap:
❏ Nipple:
*Seefaucetsectionforadditionalmodelsavailable
SEEREVERSEFORROUGHING-INDIMENSIONS
J24
© 2017 AS America Inc.
spec_0328-Townsend Ped Sink 4/17
TOWNSEND
®
PEDESTAL SINK
FINE FIRECLAY
SUPPLIES
AS REQ'D
1-1/4"
O.D. WASTE
1-1/4" O.D.
TAIL PIECE
FINISHED
FLOOR
FINISHED
WALL
8"
(202mm)
OPEN
TO
FLOOR
DRAIN
CHASE
35-1/4"
(895mm)
2"
(50mm)
8-1/2"
(215mm)
19-1/2"
(495mm)
30"
(762mm)
*22-3/4"
(578mm)
*20-1/2"
(521mm)
8-3/8"
(213mm)
8"
(203mm)
7/8"
(22mm)
FAUCET MOUNTING HOLES:
SINGLE HOLE, 4"(102mm) OR 8"(203mm)
2X HOLES FOR
ANCHOR BOLTS
PEDESTAL
BASE
NOTES:
*
DIMENSIONSSHOWNFORLOCATIONOFSUPPLIESAND“P"TRAPS
ARESUGGESTED.
▼ PEDESTALANCHORINGSCREWSNOTINCLUDED.
■SUITABLEFORREINFORCEMENTONLY.ACTUALDIMENSIONSMUST
BETAKENFROMFIXTURE.
FITTINGNOTINCLUDEDANDMUSTBEORDEREDSEPARATELY.
PROVIDESUITABLEREINFORCEMENTFORALLWALLSUPPORTS.
INSTALLATIONINSTRUCTIONSSUPPLIEDWITHLAVATORY.
IMPORTANT:Dimensionsofxturesarenominalandmayvarywithinthe
rangeoftoleranceestablishedbyANSIStandardA112.19.2
Thesemeasurementsaresubjecttochangeorcancellation.Noresponsibility
isassumedforuseofsupersededorvoidedpages.
  • Page 1 1
  • Page 2 2

American Standard 0328008.222 User manual

0328008.222
American Standard
Brand
American Standard
Model
0328008.222
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents