American Standard 0039001.020 User manual

Brand: American Standard

Model: 0039001.020

Type: User manual

J23

spec_0328-Townsend Ped Sink 4/17

TOWNSEND

PEDESTAL SINK

FINE FIRECLAY

TOWNSEND

PEDESTAL SINK

❏ 0328.800 Faucet holes on 8" (203mm) centers (Illustrated)

❏ 0328.400 Faucet holes on 4" (102mm) centers

❏ 0328.100 Center hole only

 •Finereclay

 •Classicstyledrectangularpedestallavatory

 •Rearoverow

 •Suppliedwithmountingkit

 •RightHeight

forgreatercomfortduringuse

 •Faucetledgewithlargedeckarea(faucetnotincluded)

 •Design coordinates with Townsend

Fixtures and Faucets

Nominal Dimensions:

30" x 19-1/2"

(762 x 495mm)

35-1/4"height

(895mm)

❏ 0328.008 Pedestal top-8" (203mm) centers

❏ 0328.004 Pedestal top-4" (102mm) centers

❏ 0328.001 Pedestal top-center hole only

❏ 0039.001 Pedestal only

Bowl sizes:

19" (485mm) wide,

12-3/4" (324mm) front to back,

5" (128mm) deep

Compliance Certications -

Meets or Exceeds the Following Specications:

•ASMEA112.19.2/CSAB45.1

To Be Specied:

❏ Color: ❏ White ❏ Linen

❏ Faucet Finish:

❏ Supplies:

❏ 1-1/4" Trap:

❏ Nipple:

*Seefaucetsectionforadditionalmodelsavailable

SEEREVERSEFORROUGHING-INDIMENSIONS

J24

spec_0328-Townsend Ped Sink 4/17

TOWNSEND

PEDESTAL SINK

FINE FIRECLAY

SUPPLIES

AS REQ'D

1-1/4"

O.D. WASTE

1-1/4" O.D.

TAIL PIECE

FINISHED

FLOOR

FINISHED

WALL

(202mm)

OPEN

FLOOR

DRAIN

CHASE

35-1/4"

(895mm)

(50mm)

8-1/2"

(215mm)

19-1/2"

(495mm)

30"

(762mm)

*22-3/4"

(578mm)

*20-1/2"

(521mm)

8-3/8"

(213mm)

(203mm)

7/8"

(22mm)

FAUCET MOUNTING HOLES:

SINGLE HOLE, 4"(102mm) OR 8"(203mm)

2X HOLES FOR

ANCHOR BOLTS

PEDESTAL

BASE

NOTES:

DIMENSIONSSHOWNFORLOCATIONOFSUPPLIESAND“P"TRAPS

ARESUGGESTED.

▼ PEDESTALANCHORINGSCREWSNOTINCLUDED.

■SUITABLEFORREINFORCEMENTONLY.ACTUALDIMENSIONSMUST

BETAKENFROMFIXTURE.

FITTINGNOTINCLUDEDANDMUSTBEORDEREDSEPARATELY.

PROVIDESUITABLEREINFORCEMENTFORALLWALLSUPPORTS.

INSTALLATIONINSTRUCTIONSSUPPLIEDWITHLAVATORY.

IMPORTANT:Dimensionsofxturesarenominalandmayvarywithinthe

rangeoftoleranceestablishedbyANSIStandardA112.19.2

Thesemeasurementsaresubjecttochangeorcancellation.Noresponsibility

isassumedforuseofsupersededorvoidedpages.

American Standard 0039001.020 User manual

American Standard 0039001.020 User manual

American Standard 0039001.020 User manual

Related papers

Other documents