Digitus DA-70415-1 Datasheet

USER’S MANUAL

5.25” Type

USB 2.0+1394 HARD DISK

/5.25”PORTABLE CD-ROM

COMBO BOX ENCLOSURE

(with audio out function)

Index

Page

Introduction…………………………………………………..……………… 2

Features &Specification……………………………………………………. 2

Requirements……………………..….……………………………………… 2

Package contents…………………..……………….………………………. 3

Hardware Installation…..….…………………………………………………. 4

Software Installation…...…………….……………….………………………. 17

- Page 1 -

Introduction：

This is an 5.25” 1394+USB2.0 combo hard disk /cd-rom enclosure,it will offer an easy to

carry Interface solution for user to add more storage & portable device for your PC.

Features & Specification：

1. USB INTERFACE:

▲ Interface standard: USB Ver:2.0

▲ USB connectors/cable: 1 USB B type female connector and 1 USB A TO B Cable

▲ Data transfer rate: USB2.0:High Speed 480Mbps

▲ For one 3.5 inch Hard Disk only

▲ EMI : CE & FCC

2. IEEE1394A INTERFACE

▲ Data Transfer Rate :100,200,400 (Mb/S).

▲ IEEE Standard :IEEE 1394A Compliant.

▲ Connectors : 2PORT x 6 to 6pin for exterior another 1394 HDD Box, IEEE 1394A

Standard.

▲ Separate cable bias (TPBIAS) and driver termination voltages supply for each

port.

▲ Truly Plug & Play automatic system configuration.

▲ Ideal for backup , storage Data files .

Requirements：

 IBM PC/AT Compatible or Apple iMac.G4

 USB 2.0 Host card or USB 2.0 HUB device/IEEE1394 PCI CARD

 Windows 2000, Windows XP, Windows ME or Windows 98SE operating

system /Mac OS G4.

- Page 2 -

Packing contents：

Please make sure that this package includes the following items.

Item

5.25'' HDD / CD-ROM BOX ENCLUSURE

USB A TO B CABLE/ 1394 6PIN TO 6PIN CABLE

Screw ( AFFIX CASE&HDD /CD ROM) set

POWER ADAPTER

CD DRIVER (WITH MANUAL)

PLATE SET

- Page 3 -

Chapter 1

Hardware Installation:

Optional : For portable CD-ROM box type

1. Open the two side of case as below.

- Page 4 -

2.Please open the top case.

3.Please insert vocal transmit line on your CD ROM

as below.(this cable is added by your CD-ROM normally)

- Page 5 -

4.Please connect the other side to the jump as below.

5.Please connect the IDE cable to CD-ROM

and advert the connection direction (Red

line is pin1 near the IDE red line as below.)

- Page 6 -

6.Please connect the IDE power cable to CD-ROM

as below.

- Page 7 -

7.Screwing the bottom side of case.

8.Please close the top side of case as below.

- Page 8 -

9.Please assemble the two side case as below.

10.Screwing the two side as below.

- Page 9 -

11.Please refer the correct case assembly as below.

Optional:For 3.5’ portable HDD box enclosure

type installation.

1. Open the two side of case as below.

- Page 10 -

2.Please open the top case.

3.Please screw the HDD together with plate as below.

- Page 11 -

- Page 12 -

4.Screwing the bottom side of case together with HDD.

5.Please assemble the IDE power cable with HDD.

6.Please assemble the IDE cable with HDD.

- Page 13 -

7.Please refer the view for assembly

and advert the connection direction (Red

line is pin1 near the IDE red line as below.)

8.Please close the top side of case as below.

9.Please insert the front panel side of case as below.

- Page 14 -

10.Please assemble the two side case as below.

- Page 15 -

11.Screwing the two side of connecters side as below.

- Page 16 -

Chapter 2

Software Installation：

Supported OS

Windows XP, Windows 2000, Windows ME, Windows 98SE (Windows

XP and Windows ME&Win2000 works without driver) and Mac 10.x . The

drivers supplied with this distribution are for Win98SE only.

Windows XP and Windows ME and windows 2000

You do not need to install any driver if your computer’s O.S is Windows

XP or Windows ME and Win2000 since the two O.S come with the supporting

driver. Turn On your computer, system will auto detect and attempt load driver

on “and appear new disk icon with “My Computer” icon on pc desktop

Windows 98SE INSTALLATIONAL:

1. Please insert CD into the CD-ROM

2. Please enter “My computer” and double click CD-ROM icon

3. Please double click “driver” folder

4. Please double click “ setup.exe” file as below:

- Page 17 -

5. Please click ” Next” as below:

6. Please select “I accept the terms of the licenese agreement”and click “Next”

- Page 18 -

7. Please select “Complete” and click “Next”

8. Please click “Install” for start to install driver.

- Page 19 -

Page is loading ...

Digitus DA-70415-1 Datasheet

Digitus DA-70415-1 Datasheet

Related papers

Other documents