Alcatel-Lucent OmniAccess 8550 Installation guide

Brand: Alcatel-Lucent

Model: OmniAccess 8550

Category: Gateways/controllers

Type: Installation guide

Alcatel-Lucent OmniAccess 8550

WEB SERVICES GATEWAY | RELEASE 2.0

INSTALLATION GUIDE

PRINTED ON

RECYCLED PAPER

The information presented is subject to change without notice.

Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.

Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of

Alcatel-Lucent. All other trademarks are the property of their respective owners.

Permission.

Disclaimers

Alcatel-Lucent products are intended for commercial uses. Without the appropriate

network design engineering, they must not be sold, licensed or otherwise distributed for use

in any hazardous environments requiring fail-safe performance, such as in the operation of

nuclear facilities, aircraft navigation or communication systems, air traffic control, direct

life-support machines, or weapons systems, in which the failure of products could lead

directly to death, personal injury, or severe physical or environmental damage. The

customer hereby agrees that the use, sale, license or other distribution of the products for

any such application without the prior written consent of Alcatel-Lucent, shall be at the

customer's sole risk. The customer hereby agrees to defend and hold Alcatel-Lucent

harmless from any claims for loss, cost, damage, expense or liability that may arise out of

or in connection with the use, sale, license or other distribution of the products in such

applications.

This document may contain information regarding the use and installation of

non-Alcatel-Lucent products. Please note that this information is provided as a courtesy to

assist you. While Alcatel-Lucent tries to ensure that this information accurately reflects

information provided by the supplier, please refer to the materials provided with any

non-Alcatel-Lucent product and contact the supplier for confirmation. Alcatel-Lucent

assumes no responsibility or liability for incorrect or incomplete information provided

about non-Alcatel-Lucent products.

However, this does not constitute a representation or warranty. The warranties provided for

Alcatel-Lucent products, if any, are set forth in contractual documentation entered into by

Alcatel-Lucent and its customers.

This document was originally written in English. If there is any conflict or inconsistency

between the English version and any other version of a document, the English version shall

prevail.

Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0 iii

September 2007 3HE03334AAAATQZZA Edition 02

Preface

The OmniAccess 8550 WSG Installation Guide provides the following

information to 8550 WSG installers:

• a description of the 8550 WSG hardware chassis and its

components

• a description of supported customer deployment scenarios

• a description of installation site requirements and guidelines

• a description of 8550 WSG technical and regulatory specifications

• how to install and connect the 8550 WSG

• how to power up and power down the 8550 WSG

• how to locate and interpret the 8550 WSG LEDs

• how to replace 8550 WSG hardware components

See the OmniAccess 8550 WSG Configuration and Administration

Guide for information about how to administer and configure the

8550 WSG Management Portal. This guide is available from the Help

menu on the 8550 WSG Management Portal.

Preface

iv Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0

September 2007 3HE03334AAAATQZZA Edition 02

Special information

The following are examples of how special information is presented in

this document.

Procedures in this guide

When more than one option is available, the options are identified by

a letter, for example, a or b. You must choose one of the options.

When more than one substep is required to complete a step, the

substeps are identified by roman numerals. You must complete all of

the substeps before you proceed to the next step.

Example of a procedure

The following procedure includes a step with options, and a step with

substeps.

1 You must perform this step.

2 This step offers two options. You must choose one of these options:

Danger — Danger indicates that the described activity or situation

may result in serious personal injury or death.

Warning — Warning indicates that the described activity or situation

may or will cause equipment damage.

Caution — Caution indicates that the described activity or situation

may or will cause a service interruption, or present as a security risk.

Note — Note provides important information.

Preface

Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0 v

September 2007 3HE03334AAAATQZZA Edition 02

a This is an option.

b This is another option.

3 You must perform each of these substeps:

i This is the first substep.

ii This is the second substep.

Preface

vi Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0

September 2007 3HE03334AAAATQZZA Edition 02

Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0 vii

September 2007 3HE03334AAAATQZZA Edition 02

Mandatory regulations

The following sections describe the mandatory regulations that govern

the installation and operation of the 8550 WSG system.

General precautions

If the 8550 WSG sustains damage requiring service, disconnect the

8550 WSG from the AC electrical outlet and refer servicing to an

authorized service provider.

Examples of damage requiring service include the following:

• The power cord, extension cord or plug has been damaged.

• Liquid has been spilled on the 8550 WSG or an object has fallen

into it.

• The 8550 WSG has been exposed to rain or water.

• The 8550 WSG has been dropped or damaged.

Mandatory regulations

viii Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0

September 2007 3HE03334AAAATQZZA Edition 02

To reduce the risk of personal injury or damage to the equipment,

observe the following:

• Place the 8550 WSG away from radiators, heat registers, stoves,

amplifiers, or other products that produce heat.

• Avoid inserting foreign objects through openings in the

8550 WSG.

• Never place the 8550 WSG in a wet location.

Precautions for installing and maintaining the 8550 WSG

Observe the following precautions to reduce the risk of electric shock

or damage when installing or maintaining the 8550 WSG.

• The installation and routine maintenance of the 8550 WSG must be

performed by individuals who are knowledgeable about the

procedures, precautions, and hazards associated with equipment

containing hazardous energy levels.

• Power down the 8550 WSG and disconnect all AC power cords

before removing any access covers for non-hot plug areas.

• Do not replace non-hot plug components while power is applied to

the product. First, shut down the product and disconnect all AC

power cords,

• Verify that the AC power supply branch circuit that provides power

to the rack is not overloaded. This will reduce the risk of personal

injury, fire, or damage to the equipment. The total rack load should

not exceed 80% of the branch circuit rating. Consult the electrical

authority having jurisdiction over your facility wiring and

installation requirements.

Mandatory regulations

Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0 ix

September 2007 3HE03334AAAATQZZA Edition 02

Power cords

To reduce the risk of electric shock or damage to the equipment,

observe the following:

• You must use a power cord rated for the 8550 WSG and for the

voltage and current marked on the electrical ratings label of the

8550 WSG. The voltage and current rating of the cord must be

greater than the voltage and current rating marked on the

8550 WSG.

• Do not place objects on AC power cords or cables. Arrange them

so that no one may accidentally step on or trip over them.

• Do not pull on a cord or cable. When unplugging from the electrical

outlet, grasp the cord by the plug.

• Make sure that the total ampere rating of all products plugged into

an extension cord or power strip does not exceed 80% of the

ampere ratings limit for the extension cord or power strip.

• Do not disable the power cord grounding plug. The grounding plug

is an important safety feature.

• Plug the power cord into a grounded (earthed) electrical outlet.

Power supplies

Installation of the 8550 WSG must comply with local and regional

electrical regulations governing the installation of information

technology equipment by licensed electricians. The 8550 WSG is

designed to operate in installations covered by NFPA 70, 1999 Edition

(National Electric Code) and NFPA-75, 1992 code for Protection of

Electronic Computer/Data Processing Equipment). See table A-1 for

electrical power ratings.

Caution — Use a regulating UPS to protect the 8550 WSG from

power fluctuations and temporary interruptions.

Mandatory regulations

x Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0

September 2007 3HE03334AAAATQZZA Edition 02

Hot-plug power supplies are not designed to be removed or installed

with AC power connected to the power supply. To reduce the risk of

electric shock or damage to the equipment when handling hot-plug

power supplies, observe the following:

• Install the power supply before connecting the power cord to the

power supply.

• Unplug the power cord before removing the power supply from the

8550 WSG.

• If the system has multiple sources of power, you must unplug all

AC power cords from the power supplies to completely disconnect

power from the system.

• Verify that the external power source connected to the 8550 WSG

matches the type of power source indicated on the electrical ratings

label.

UPS Products

To reduce the risk of electric shock and/or equipment damage when

installing or servicing UPS products, observe the following:

• The installation of options and routine maintenance of UPS

products must be performed by trained service technicians who are

knowledgeable about the procedures, precautions, and hazards

associated with AC power products.

• Hardwired UPS products require a direct connection to a dedicated

AC branch circuit (AC mains). Connection should only be

performed by a licensed electrician.

• Do not operate a UPS that is disconnected from AC Power. Use the

TEST/ALARM RESET button to test the batteries. Disconnect all

protected loads before disconnecting the UPS from AC Power.

• Pluggable UPS products must be disconnected and unplugged from

AC power before servicing the product or replacing a non-hot plug

component.

• Do not overload the output of the UPS. The total connected load

should not exceed 80% of the rated output.

• Do not exceed the leakage current limit for the type of UPS in your

system.

• Do not exceed the maximum number of UPS products in any single

rack.

• Install the UPS only at the bottom of a rack.

Mandatory regulations

Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0 xi

September 2007 3HE03334AAAATQZZA Edition 02

Batteries

The 8550 WSG contains internal lithium manganese dioxide batteries

or vanadium pentoxide batteries. There is risk of fire and burns if the

battery pack is not handled properly. To reduce the risk of personal

injury, observe the following:

• Do not attempt to recharge the battery.

• Do not expose the battery to temperatures higher than 60°C

(140°F).

• Do not disassemble, crush, puncture, short external contacts, or

dispose of the battery in fire or water.

• Replace the battery only with the spare battery designated for this

product.

• Do not dispose of batteries with the general household waste. To

forward them to recycling or proper disposal, use the public

collection system.

Manual handling of equipment

To reduce the risk of personal injury or damage to the equipment,

observe the following:

• Obtain adequate assistance to lift and stabilize the 8550 WSG

during installation or removal.

• Remove all pluggable power supplies and modules to reduce the

weight of the 8550 WSG.

• Remove all pluggable power supplies and modules to reduce the

weight of the 8550 WSG.

• Ensure the 8550 WSG is properly mated with the rails.

Mandatory regulations

xii Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0

September 2007 3HE03334AAAATQZZA Edition 02

Rack installation precautions

To reduce the risk of personal injury or damage to the equipment,

observe the following:

• The leveling jacks are extended to the floor.

• The full weight of the rack rests on the leveling jacks.

• The stabilizing feet are attached to the rack if it is a single-rack

installation.

• The racks are coupled together in multiple-rack installations.

• Only one component is extended at a time. A rack may become

unstable if more than one component is extended for any reason.

• You are careful when pressing the component rail release latches

and sliding the component into the rack. The slide rails could pinch

your fingertips.

• You load the rack from the bottom up and load the heaviest item

into the rack first.

• You do not attempt to move equipment racks without adequate

assistance, due to their height and weight.

• You do not attempt to move an equipment rack on an incline that is

greater than 10 degrees from horizontal.

• You do not attempt to move a fully loaded equipment rack.

Remove equipment from the rack before moving the rack not

attempt to recharge the battery.

Preventing electrostatic discharge and safety procedures

A discharge of static electricity from a finger or other conductor may

damage system boards or other static-sensitive devices. This type of

damage may reduce the life expectancy of the device.

Mandatory regulations

Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0 xiii

September 2007 3HE03334AAAATQZZA Edition 02

To prevent electrostatic damage, do the following:

• Avoid hand contact by transporting and storing products in

static-safe containers.

• Keep electrostatic-sensitive parts in their containers until they

arrive at a static-free workstation.

• Place parts on a grounded surface before removing them from their

containers.

• Avoid touching pins, leads, or circuitry.

• Always be properly grounded when touching a static-sensitive

component or assembly.

Grounding methods to prevent electrostatic discharge

Use one or more of the following methods when you handle or install

electrostatic-sensitive parts:

• Use a wrist strap connected by a ground cord to a grounded

workstation or computer chassis. Wrist straps are flexible straps

with a minimum of 1 megohm ± 10% resistance in the ground

cords. To provide proper grounding, wear the strap snug against the

skin.

• Use heel straps, toe straps, or boot straps at standing workstations.

Wear the straps on both feet when standing on conductive floors or

dissipating floor mats.

• Use conductive field service tools.

• Use a portable field service kit with a folding static-dissipating

work mat.

If you do not have any of the suggested equipment for proper

grounding, have an authorized reseller install the part.

Mandatory regulations

xiv Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0

September 2007 3HE03334AAAATQZZA Edition 02

Guidelines for branch circuits

When you install more than one 8550 WSG, you may need to use

additional power distribution devices to safely provide power to all

devices. Observe the following guidelines:

• Balance the server power load between available AC supply branch

circuits.

• Do not allow the overall system AC current load to exceed 80% of

the branch circuit AC current rating.

• Do not use common power outlet strips.

• Provide a separate electrical circuit for the 8550 WSG.

Warning — To reduce the risk of personal injury, fire, or damage to

equipment, do not overload the AC supply branch circuit that

provides power to the rack. Consult the electrical authority having

jurisdiction over wiring and installation requirements of your facility.

Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0 xv

September 2007 3HE03334AAAATQZZA Edition 02

Contents

Preface iii

Special information.................................................................................... iv

Procedures in this guide............................................................................ iv

Example of a procedure ................................................... iv

Mandatory regulations vii

General precautions ..................................................................................vii

Precautions for installing and maintaining the 8550 WSG .......................viii

Power cords .............................................................................................. ix

Power supplies .......................................................................................... ix

UPS Products............................................................................................. x

Batteries ................................................................................................. xi

Manual handling of equipment .................................................................. xi

Rack installation precautions.....................................................................xii

Preventing electrostatic discharge and safety procedures........................xii

Grounding methods to prevent electrostatic discharge ............................xiii

Guidelines for branch circuits ...................................................................xiv

Contents

xvi Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0

September 2007 3HE03334AAAATQZZA Edition 02

1 — Overview 1-1

1.1 Introduction ............................................................................1-2

1.2 8550 WSG deployment planning ...........................................1-2

Virtualized internal services for external

consumption..................................................................1-3

Virtualized external services for internal

consumption..................................................................1-4

Internal services for internal consumption..........................1-5

Internal services for internal consumption and

virtualized external services for internal

consumption..................................................................1-6

High Availability configuration ............................................1-7

1.3 Hardware description .............................................................1-8

Front panel .........................................................................1-8

Rear panel..........................................................................1-9

Power management ...........................................................1-9

Cooling ...............................................................................1-9

Hot pluggable hard drives ................................................1-10

Ports.................................................................................1-10

Cable management arm...................................................1-11

1.4 Installation tasks ..................................................................1-12

2 — Site Preparation 2-1

2.1 Before you begin ....................................................................2-2

2.2 Cable requirements................................................................2-2

Types of cables ..................................................................2-2

2.3 Selecting an appropriate location for the chassis...................2-3

Keeping the chassis cool ...................................................2-3

Environmental considerations ............................................2-3

3 — Installing and connecting the 8550 WSG 3-1

3.1 8550 WSG installation procedures.........................................3-3

3.2 Unpacking the 8550 WSG .....................................................3-3

Procedure 3-1 To unpack the 8550 WSG .....................3-3

3.3 Recording the serial number of the 8550 WSG .....................3-3

Procedure 3-2 To record the serial number of

the 8550 WSG ........................................................3-4

3.4 Installing the rails for the 8550 WSG in a rack .......................3-4

Procedure 3-3 To install the rails...................................3-4

Contents

Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0 xvii

September 2007 3HE03334AAAATQZZA Edition 02

3.5 Attaching the 8550 WSG to the rails ......................................3-7

Procedure 3-4 To attach the 8550 WSG to the

rails .........................................................................3-8

3.6 Cabling the 8550 WSG ........................................................3-10

Procedure 3-5 To connect the cables to the

8550 WSG ............................................................3-12

3.7 Installing the cable management arm ..................................3-13

Procedure 3-6 To install the cable management

arm .......................................................................3-13

3.8 Converting the cable management arm for a

right-hand swing.............................................................3-15

Procedure 3-7 To convert the cable management

arm for a right-hand swing....................................3-16

3.9 Connecting the AC power cords to the 8550 WSG..............3-22

Procedure 3-8 To connect the AC power cords ..........3-22

3.10 Connecting the 8550 WSG High Availability ports...............3-23

Procedure 3-9 To connect the 8550 WSG High

Availability ports....................................................3-23

3.11 Configuring the PC that connects to the 8550 WSG

Management Portal........................................................3-24

Procedure 3-10 To configure the 8550 WSG IP

address on the PC that connects to the

8550 WSG Management Portal............................3-24

3.12 Connecting the 8550 WSG management port to a

router or network switch .................................................3-25

Procedure 3-11 To connect the 8550 WSG

management port to a router or network

switch....................................................................3-25

3.13 Connecting the 8550 WSG Ethernet data network

ports to a router or network switch .................................3-26

Procedure 3-12 To connect the 8550 WSG

Ethernet data network ports to a router or

network switch ......................................................3-26

4 — Getting started 4-1

4.1 Powering up the 8550 WSG ..................................................4-2

Procedure 4-1 To power up the 8550 WSG ..................4-2

4.2 Initializing the 8550 WSG Management Portal ......................4-2

Procedure 4-2 To log in to the 8550 WSG

Management Portal to initialize the system ............4-2

Contents

xviii Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0

September 2007 3HE03334AAAATQZZA Edition 02

4.3 Logging out of the 8550 WSG Management Portal ...............4-4

Procedure 4-3 To log out of the 8550 WSG

Management Portal ................................................4-4

5 — LEDs 5-1

5.1 LEDs ......................................................................................5-2

Front panel .........................................................................5-2

Rear panel LEDs................................................................5-8

A. 8550 WSG chassis specifications A-1

A.1 Chassis specifications........................................................... A-2

Technical specifications .................................................... A-2

Regulatory specifications .................................................. A-3

B. Replacing system components B-1

B.1 Field Replaceable Units ........................................................ B-2

B.2 Powering down the 8550 WSG ............................................. B-2

Procedure B-1 To power down the 8550 WSG............ B-2

B.3 Replacing the 8550 WSG ..................................................... B-3

Procedure B-2 To remove the 8550 WSG from

the rails .................................................................. B-3

B.4 Replacing the power supply .................................................. B-4

Procedure B-3 To replace the power supply ................ B-4

B.5 Replacing a hard drive .......................................................... B-5

Procedure B-4 To replace a hard drive ........................ B-5

Glossary

Index

Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0 1-1

September 2007 3HE03334AAAATQZZA Edition 02

1 — Overview

1.1 Introduction 1-2

1.2 8550 WSG deployment planning 1-2

1.3 Hardware description 1-8

1.4 Installation tasks 1-12

1 — Overview

1-2 Alcatel-Lucent OmniAccess 8550 WSG Installation Guide, Release 2.0

September 2007 3HE03334AAAATQZZA Edition 02

1.1 Introduction

This document describes how to install the 8550 WSG and initialize

the 8550 WSG Management Portal so that you can perform

configuration and administration tasks. See the OmniAccess

8550 WSG Configuration and Administration Guide for information

on how to perform these tasks.

The 8550 WSG offers the following features:

• performance—Intel Processors and memory technology

• reliability—redundant hot pluggable hard drives, disk-based back

up, redundant power supplies, and redundant fans

• management—System Insight Display LEDs that provide status

monitoring for system health, integrated power monitoring, and

automatic recovery

1.2 8550 WSG deployment planning

The 8550 WSG can be deployed to virtualize any combination of the

following scenarios:

• virtualized internal services for external consumption

Internal web services are configured on the 8550 WSG and access

is provided to external users, such as partners.

• virtualized external services for internal consumption

External services are configured on the 8550 WSG to allow access

to internal users.

• internal services for internal consumption

Only web services published within an Enterprise are configured

on the 8550 WSG.

• internal services for internal consumption and virtualized external

services for internal consumption

The 8550 WSG is configured to allow internal web services for

internal consumption within an Enterprise, and virtualized external

services for internal consumption.

WS client applications do not have any direct knowledge or access to

WS applications that may exist behind the 8550 WSG. The 8550 WSG

drops any request for a service it has not been configured to virtualize.

Page is loading ...

Alcatel-Lucent OmniAccess 8550 Installation guide

Brand: Alcatel-Lucent

Model: OmniAccess 8550

Category: Gateways/controllers

Type: Installation guide

Download PDF

report

Alcatel-Lucent OmniAccess 8550 Installation guide

Alcatel-Lucent OmniAccess 8550 Installation guide

Related papers

Other documents