Page is loading ...
11
AcAdemy
1
P/N C3843001 RL0110
Safety and the proper operation of your Casablanca fan both require a thorough knowledge
of the product and proper installation; therefore, before attempting to install and operate your
Casablanca fan, read this owner’s manual completely and carefully. Retain this manual for
future reference.
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off
at the circuit breaker or fuse box before attempting any installation procedure.
AcAdemy Owner’s Manual
READ AND SAVE THESE INSTRUCTIONS!
CONTENTS
Introduction _______________________________________________________________________7
Before You Start ................................................................................................................................................ 7
Safe Use
............................................................................................................................................................ 7
Mounting Recommendations
.......................................................................................................................... 8
Sloped Ceiling Installation
............................................................................................................................... 8
Fan Installation ____________________________________________________________________9
Getting Started .................................................................................................................................................. 9
Mounting Bracket Installation
.......................................................................................................................... 9
Canopy Installation
.......................................................................................................................................... 11
Fan Preparation
................................................................................................................................................11
Hanging the Fan
...............................................................................................................................................13
Canopy Electrical Connections
.......................................................................................................................14
Canopy Hatch and cover ring Installation
......................................................................................................14
Blade Installation
.............................................................................................................................................15
Blade Installation
.............................................................................................................................................15
Switch housing and end cap installation ....................................................................................................17
Academy Gallery Light Kit Installation _____________________________________________19
Troubleshooting tips
____________________________________________________________ 23
Care Recommendations
__________________________________________________________ 23
Product Specications
___________________________________________________________ 24
PArts List
If you are in need of service parts, do not return this fan to the store. Call our Support Center toll free at 1-888-227-2178
AcAdemy
25
24
26
27
22
20
21
28
29
19
5
4
33
34
6
7
31
30
32
16
9
12
14
1
18
13
Call our Support Center toll free at 1-888-227-2178
Parts List
Model # C38U199K C38U11K C38U45K C38U73K
Asm. Dwg. # 99444-01 99444-02 99444-03 99444-04
Finish Chrome
Snow
White
Brushed
Nickel
Oil Rubbed
Bronze
Item
#
Item Name
Qnty
Part # Part # Part # Part #
2 Hang-True® Canopy Assembly
1 98881-01-199 98881-02-203 98881-02-214 98881-01-308
19
Hang-True® Canopy Cover 1
76933-01-199 76933-01-203 76933-01-214 76933-01-308
20
Canopy
1 98889-01-199 98889-01-199 98889-01-199 98889-01-199
21
Canopy Door
1 88693-01-199 88693-01-203 88693-01-214 88693-01-308
22
Ceiling Plate
1 88694-01-000 88694-01-000 88694-01-000 88694-01-000
23
Isolators (pre-installed)
4
3 Hardware Kit A
1 67256-03-000 67256-03-000 67256-03-000 67256-01-000
24 3/8” Washer
1
25 Wire Nut
4
26 #8 Flat Washer
2
27 3/8” Lag Screw
1
28 8-32 Screw
2
98 Lock Washer
4
29 8-32 Bolt
4
4 Hanger Pipe
1 77745-04-199 77745-25-203 77745-04-214 77745-04-308
5
Adapter Cover
1 76931-01-000 76931-02-000 76931-03-000 76931-04000
6
Blade Iron
1 89166-09-000 89166-10-000 89166-11-000 89166-12-000
7
Blade Set 1
G0113-33-000 G0113-34-000 G0113-35-000 G0113-36-000
8
Blade Hardware Kit
1
89440-23-000 89440-23-000 89440-23-000 89440-19-000
30
Blade Screws
21
31 Blade Washers
21
15 Hardware Kit B
1 G0111-20-000 G0111-20-000 G0111-20-000 G0111-21-000
32
#12 Blade Iron Screws
11
10 Hardware Kit C 1
G0221-01-000 G0221-01-000 G0221-01-000 G0221-01-000
33
Set Screw (pre-installed)
1
34 #6-32 Screw .62”
1
35 #6-32 Screw 1.25”
4
36 #8-32 Screw .38”
3
9 Switch Housing
1 89163-01-000 89163-02-000 89163-03-000 89163-04-000
12
Switch Housing Cap
1 98884-01-199 98884-01-203 98884-01-214 98884-01-308
13
Bottom Cap, No Light Kit
1 88692-01-199 88692-01-203 88692-01-214 88692-01-308
16
Screw Plug, No Light Kit
1 76932-01-199 76932-01-203 76932-01-214 76932-01-308
14
Pull Chain Pendant
3 77257-08-000 77257-09-000 77257-08-000 77257-07-000
1
Screwdriver #2 Phillips
1 65567-01-000 65567-01-000 65567-01-000 65567-01-000
99
Allen Wrench
1 64801-03-000 64801-03-000 64801-03-000 64801-03-000
18
Balancing Kit
1 65520-01-000 65520-01-000 65520-01-000 65520-01-000
98
35
36
99
PArts List
If you are in need of service parts, do not return this fan to the store. Call our Support Center toll free at 1-888-227-2178
AcAdemy GALLery
25
24
26
27
22
20
21
28
19
5
4
33
36
34
7
31
30
32
14
9
17
12
11
1
18
13
16
6
Parts List
Model # C38G199K C38G11K C38G45K C38G73K
Asm. Dwg. # 99443-05 99443-06 99443-07 99443-08
Finish Chrome
Snow
White
Brushed
Nickel
Oil Rubbed
Bronze
Item # Item Name Qnty Part # Part # Part # Part #
2 Hang-True® Canopy Assembly 1 98881-01-199 98881-02-203 98881-02-214 98881-01-308
19
Hang-True® Canopy Cover
1 76933-01-199 76933-01-203 76933-01-214 76933-01-308
20
Canopy
1 98889-01-199 98889-01-203 98889-01-214 98889-01-308
21
Canopy Door 1
88693-01-199 88693-01-203 88693-01-214 88693-01-308
22
Ceiling Plate
1 88694-01-000 88694-01-000 88694-01-000 88694-01-000
23
Isolators (pre-installed)
4
3 Hardware Kit A 1
67256-03-000 67256-03-000 67256-03-000 67256-01-000
24
3/8” Washer
1
25 Wire Nut
4
26 #8 Flat Washer
2
27 3/8” Lag Screw
1
28 8-32 Screw
2
98 Lock Washer
4
29 8-32 Bolt
4
4
Hanger Pipe 1 77745-04-199 77745-25-203 77745-04-214 77745-04-308
5
Adapter Cover 1 76931-01-000 76931-02-000 76931-03-000 76931-04-000
6 Blade Iron 1 89166-09-000 89166-10-000 89166-11-000 89166-12-000
7
Blade Set 1
G0113-33-000 G0113-34-000 G0113-35-000 G0113-32-000
8 Blade Hardware Kit 1
89440-23-000 89440-23-000 89440-23-000 89440-19-000
30
Blade Screws
21
31 Blade Washers
21
15
Hardware Kit B 1 G0111-20-000 G0111-20-000 G0111-20-000 G0111-20-000
32
#12 Blade Iron Screws
11
37 1/4” Screws (pre-installed)
5
10
Hardware Kit C 1 G0187-01-000 G0187-01-000 G0187-01-000 G0187-02-000
33
Set Screw (pre-installed)
1
34 #6-32 Screw .25”
3
36 #8-32 Screw .38”
3
17
Switch Housing 1 89170-01-199 89170-01-203 89170-01-214 89170-01-308
9
Light Kit Assembly 1
G0186-01-000 G0186-02-000 G0186-03-000 G0186-04-000
11 Glass Bowl 1 89167-01-000 89167-01-000 89167-03-000 89167-02-000
12
Finial Cap 1
77353-05-000 77353-06-000 77353-07-000 77353-08-000
13 Finial 1 77352-01-199 77352-01-203 77352-01-214 77352-01-308
14 40W G-16 E-12 Candelabra Bulb 3 77756-10-000 77756-10-000 77756-10-000 77756-10-000
16
Pull Chain Pendant 2
77257-08-000 77257-09-000 77257-08-000 77257-07-000
1 Screwdriver #2 Phillips 1 65567-01-000 65567-01-000 65567-01-000 65567-01-000
99 Allen Wrench 1 64801-03-000 64801-03-000 64801-03-000 64801-03-000
18 Balancing Kit 1 65520-01-000 65520-01-000 65520-01-000 65520-01-000
29
98
99
6
7
66
AcAdemy
7
AcAdemy
7
Motor Identication Plate
RECORD MODEL AND SERIAL NUMBERS BEFORE INSTALLATION!
Please take a moment to locate the model number and serial number from your fan (see below) and record
this information on the Warranty page inside the front cover of your Owner’s Manual if it does not appear
there already. These numbers are found on the motor identication plate afxed to the fan motor in the
location shown below:
PLEASE INSPECT ALL PACKAGING PRIOR TO DISCARDING!
Your Casablanca fan was crafted with pride and care and inspected thoroughly prior to
shipment. Before you begin to assemble and install your Casablanca fan, remove all
parts from the carton and check them against the Parts Guide in this manual.
Make sure all parts are included in the box using the Parts Guide on the following pages.
If there are missing or broken parts:
Call 1-888-227-2178 Monday through Friday, 8a.m.
to 5 p.m. Central. Your request will be handled
immediately. Replacement parts will be sent to you
via Federal Express.
Proper Parts Handling
Do not remove lightbulbs from their packaging
until you are ready to install them.
Before discarding packaging materials, be certain
that all parts have been removed.
Use a clean, dry paintbrush to remove small
Styrofoam pieces that may remain after unpacking.
Do not brush Styrofoam into wiring cavities.
The blades in each pack are matched for equal
weight to assure smooth fan operation. If more
than one fan is being installed, do not mix blades
from different cartons.
When cleaning, painting, or working near your fan,
be cautious of the fan and blades.
Always turn power to the ceiling fan OFF before
replacing lightbulbs or working on your fan.
Never insert anything into the path of the fan
blades while the fan is in operation.
Never install a fan over a pool or spa.
Never operate a fan that has been damaged in any
way.
Install the fan according to the instructions in this
manual.
If the fan does not work:
Refer to the Troubleshooting Tips in this Owner’s
Manual.
Call Technical Support at 1-888-227-2178.
Contact your local Authorized Service Center.
Our Web site at www.casablancafanco.com
contains additional information on Casablanca
products, troubleshooting, and Authorized Dealer
or Service Centers. Please do not return this
product to the store.
Serial Number
Presidio
TYPE HANGER TYPE
DJ01 1151 MODEL C38U199K
Memphis, TN
SERIAL No.: DJ06 2237
C38U199K
Model Number
Circuit Breaker
(Trip breaker for the
circuit you will be
working on)
Fuse Box
(Remove fuse for the
circuit you will be
working on)
18"
70"
SAFE USE
• CAUTION: RISK OF ELECTRICAL SHOCK! Installation is to be in accordance with the National Electrical
Code, ANSI/NFPA 70-1999 and local codes. If you are unfamiliar with the wiring codes, you should use
a qualied electrician.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed
for ceiling fan installations. If it is not, a new box must be installed. Casablanca extension poles are
available for sloped or high ceiling installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit.
The maximum current requirement for the fan with light xture is 2 amps. The fan uses about 1 amp or
100 watts. Maximum light current is 1amp or 120 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the
canopy, make sure all wires are within the canopy and that no wires are being pinched.
WARNING: Do not bend the blade brackets when installing the brackets, balancing the blades, or
cleaning the fan. Do not insert foreign objects in between the rotating fan blades.
Unpacking
Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check
them against the parts listed in the Parts Guide. Before discarding packaging materials, be certain that all
parts have been removed.
For best performance and for your warranty to be valid, use only genuine Casablanca blades, light
xtures, and accessories.
INTRODUCTION
• The blades in each pack are matched for equal
weight to assure smooth fan operation. If more
than one fan is being installed, be careful not to
mix blades from different cartons.
• It is always a good idea to have an assistant to
help with the installation.
• Always turn the power OFF to the ceiling fan
before working on it or replacing lightbulbs.
BEFORE YOU START
84"
8
9
88
AcAdemy
9
AcAdemy
9
MOUNTING RECOMMENDATIONS
SLOPED CEILING INSTALLATION
Before mounting your Casablanca fan, read the following helpful recommendations. The location of the
fan, air circulation, and fan size are all important factors to consider before installation.
Location
Ceiling fans have practical uses in almost every room
in your home. We suggest you follow these mounting
recommendations as you decide where to install your
Casablanca fan.
• For safety reasons, the fan blades must be a minimum of 7'
above the oor.
• Do not locate the fan in a doorway or above a swinging door.
• In bedrooms, fans work best when mounted above the foot of
the bed.
• Over pool tables, be sure to provide plenty of clearance to avoid
damage from pool cues.
• In kitchens be sure to allow for open cupboard doors to clear
the fan blades.
• Do not install a fan close to or over a pool or spa. High humidity combined with corrosive gases will
destroy the nish and warp the blades.
Fan Size
Variable fan speed capability permits the use of a full-size 52" fan even in smaller rooms. For very large
rooms, two fans may be needed.
Calculation of Ceiling Angle
Use the tear-off Ceiling Angle Template card inserted
in this manual. It provides you with a simple “go”
or “no-go” for installing your fan on a sloped
ceiling.
7' minimum
When to Use Extension Poles
For optimum performance and appearance,
an extension pole should be used with your
Casablanca fan when installing on high (cathedral)
ceilings or sloped ceilings. Casablanca offers
standard poles in increments of 6" up to 5'. Custom
poles are available in lengths up to 9'9". See your
Authorized Casablanca Dealer for details.
Blades must be a
minimum of 7 feet
above the oor
Extension
Pole
Maximum
®
angle 32º
This slope is less than 32º.
It is OK to install your fan.
This slope is 32º. This is the maximum
slope that will allow the fan to hang
straight down. It is OK to install your
fan.
This slope is more than 32º. Your fan will
not hang straight down, an adaptor is
necessary. Contact your local Authorized
Casablanca Dealer in regards to purchasing
a “Sloped Ceiling Adaptor.”
Note: Fan may wobble or vibrate if pole length is
not long enough and inside blade is too close to
downslope or side wall. Extending pole length will
usually solve problem.
EXAMPLE 3
EXAMPLE 2
EXAMPLE 1
Suggested Extension Pole Lengths
Ceiling Height Pole Length
8' 0" 4.5"
8' 6" 4.5"
9' 0" 12"
9' 6" 12"
10' 0" 18"
11' 0" 24"
12' 0" 36"
13' 0" 48"
14' 0" 60"
Using Existing Ceiling Fixture Outlet Box
After turning the power OFF at its source (either
the circuit breaker or fuse box), lower the old
xture and disconnect the wiring. Check the
ceiling xture outlet box to be sure it is marked
“Approved for Ceiling Fan Mounting.” If it is not,
a new box must be installed.
GETTING STARTED
Installing a New Ceiling Fixture Outlet Box
If you do not have an existing xture located
where you wish to place your Casablanca fan,
an approved ceiling xture outlet box must be
installed and wired.
Note: The weight of this fan is 32 pounds.
WARNING!
To reduce the risk of re, electrical shock, or
personal injury, mount to outlet box marked
“Acceptable Fan Support of 22.7 kg (50
lbs.) or less” using the mounting hardware
provided with the outlet box or directly to
structure.
FAN INSTALLATION
NOTE: Lag Screw installatin is required only under two conditions:
• Fan weighs 36 lbs. or more
• Iftheexistingceilingxtureoutletboxneedstobemodiedforaceilingfanapplication(for
example,ifthehouseisnotnewconstructionandyouarereplacinganexistinglightxture).
Werecommendthattheceilingboxbeofsufcientcapacitytosupporttheweightofthefanandlight
xtureunderanyconditions.Ifindoubtwhetheryouneedtoinstallthelagscrew,consultaqualied
electrician.
LAG SCREW INSTALLATION
Note: After removing the old xture, check the
outlet box to insure that it is supported by a joist
or beam across its upper surface. If not, a 2 x4
stud must be installed.
Step 1. Remove the knockout plug in the center of the
outlet box or drill a
1
/
2
-inch hole for the lag screw to pass
through. Then drill a
1
/
4
-inch guide hole into the joist or
beam to a depth of 3 inches.
Step 2. Thread the lead wires from the outlet box
down through the large hole in the the ceiling plate.
Step 3. Align the slotted holes in the ceiling plate
with the screw holes in the outlet box.
Note: The isolators should be ush against the ceiling.
CEILING HARDWARE (not to scale)
Mounting Bracket
Lag Screw and Washer (1)
1" x 8-32 Roundhead Screw and
Washer (2)
Wire Nut (4)
10
11
1010
AcAdemy
11
AcAdemy
11
CANOPY HARDWARE
CANOPY INSTALLATION
Canopy
Canopy
Hatch
Canopy Screws and (4) Lock
Washers
Phillips
Screwdriver
Lock
Washer
Canopy
Screw
Canopy
Step 1. Attach the canopy to the ceiling plate with
three of the 8-32 x 2
1
/
2
" long canopy screws and
lock washers provided with your Casablanca fan.
Tighten using the provided screwdriver until snug
against the ceiling.
NOTE: On sloped ceilings, align the canopy
opening with the top or peak of the room.
FAN PREPARATION
FAN PREPARATION
PAPER MOTOR
SHIELD
FIGURE 1.
Prepare for fan installation as follows:
Step 1. Remove the paper shield from the motor
as shown in Figure #1.
Step 2. Using the provided Allen wrench (attached
to the paper motor shield), loosen the Allen set
screw making sure that end of the Set Screw can
not be seen within the motor coupling as shown
in Figure #2. If so, you will need to unscrew the
Set Screw so that the tip of the Set Screw does not
remain in the path of the downrod.
Perma•Lock™ Downrod
and Ball Assembly
Hanging Adapter
Cover
Canopy Cover
Ring
Allen Wrench
FIGURE 2.
Set Screw
MOUNTING BRACKET INSTALLATION CONT.
Step 1. Place a at washer on each of the two
screws that came with the outlet box and pass the
screws through the slotted holes in the ceiling plate
into the screw holes in the outlet box.
Step 2. Tighten the screws into the outlet box;
do not use lubricants on the screws. Do not over
tighten.
Step 3. Install the lag screw if needed pass the lag
screw with the large washer attached through the
center hole of the ceiling plate and screw into the
guide hole. Tighten until the outlet box is mounted
rmly to the beam. This box must be secured to the
ceiling rmly.
Joist
Ceiling Fan
Approved
Wiring Box
Washer
Lag Bolt
Joist
Ceiling Fan
Approved
Wiring Box
Washer
Outlet
Box
Screw
Outlet
Box
Screw
12
13
1212
AcAdemy
13
AcAdemy
13
Step 3. Slide both the hanging adapter cover and
canopy cover ring on to the downrod, then route
the wires through the 3.5" Perma•Lock downrod
and ball assembly as shown in Figures #3. Insert
the downrod into the motor coupling and turn it
clockwise until it stops turning, ensuring that the
downrod has bottomed out.
Tip: The downrod has a tapered thread that
is designed to lock completely when installed
correctly.
CAUTION: Failure to fully lock in the
downrod before securely tightening the
set screw may cause the fan to separate
from the downrod and fall during normal
operation.
FIGURE 3.
HANGING
ADAPTER COVER
TAPERED
THREAD
MOTOR
COUPLING
MOTOR WIRES
(LEAVE AT LEAST
6" LONG)
PERMA•LOCK™
DOWNROD AND
BALL ASSEMBLY
MOTOR
HOUSING
ASSEMBLY
SET SCREW
CANOPY COVER
RING
Step 4. Tighten the set screw as shown in Figure
#4 to ensure safe operation of your fan. If it is tight
enough, you should not be able to turn the downrod
counterclockwise with your hands. If in doubt, tighten
the set screw until you cannot turn it any further.
Set Screw
FIGURE 4.
CAUTION: The Motor Adapter has a special
coating on the threads. Do not remove this
coating; the coating prevents the downrod
from unscrewing. Once assembled, do not
remove the downrod.
Step 5. Slide the hanging adapter cover down over
the motor coupling as shown in Figure #5, making sure
that the adapter cover is covering the motor coupling
as in shown Figure #6.
FIGURE 5.
FIGURE 6.
HANGING THE FAN
Step 1. To hang the fan body in the canopy,
hold the fan body rmly and insert the ball into
the canopy opening as in Figure #1. Check that no
wires are pinched. Rotate the fan body until the
slot in the ball ts into the pin opposite the canopy
opening in Figure #2.
FIGURE 1.
FIGURE 2.
Slot
Pin
14
15
1414
AcAdemy
15
AcAdemy
15
FIGURE 4.
CANOPY ELECTRICAL CONNECTIONS
Step 1. Tuck the wires into the canopy with the
wire nuts pointed upwards, so that the WHITE and
BLACK wires are on opposite sides of the canopy
and all wires are clear of the canopy opening.
Step 2. Install the canopy hatch with the last
canopy screw and lock washer using the provided
screwdriver. To do this, tilt the fan body away from
the hatch opening. Tighten the screws Figure 3.
Step 3. Straighten the fan, then check to ensure
there is no movement between the canopy and the
ceiling or the Perma•Lock™ downrod and the ball
assembly.
Step 4. Locate the locking pins on the canopy
cover ring as shown in Figure 5. Lift up on the
canopy cover ring and guide the two (2) locking
pins into the two (2) locking holes, then snap the
canopy cover in to place as shown in Figure 4.
FIGURE 3.
CANOPY HATCH AND COVER RING INSTALLATION
SWITCH
HOUSING
SCREWS
BLADE HARDWARE
BLADE INSTALLATION
Screw Driver
Blades (5)
Blade Irons (5)
Blade
Screws (21)
Blade Iron
Screws (11)
Step 1. Remove the ve shipping blocks, and
screws as shown in Figure #1. DO NOT discard the
ten (10) screws; you will need them for installing
the blades onto the fan.
Blade
Washers (21)
Step 2. Attach a blade to a blade iron by rst
pressing the blade iron onto the blade, then attaching
the blade using 4 blade screws and blade washers as
shown in Figure #2. Using the provided screwdriver,
tighten securely by hand only. Repeat for each blade
assembly.
Shipping Block
Blade Iron
Screws
FIGURE 1.
FIGURE 2.
CAUTION:
Blade screws must be tightened securely
before operating the fan.
Step 3. Attach a blade/blade iron assembly
to the ywheel by using two blade iron screws
provided. Place the end of the blade iron on the
ywheel as shown in Figure 3. Insert the screws
one by one using the provided screwdriver.
Tighten securely by hand only. Repeat for each
blade/blade iron assembly until all ve blades
are attached to the fan.
FIGURE 3.
Fly Wheel
Blade Iron
Screws
Blade Iron
BLADE IRON
BLADE WASHER
BLADE
BLADE IRON
SCREWS
NOTE: If the color of your ceiling wires differs from that described, consult an electrician.
2 BLACK WIRES &
1 BLUE WIRE
2 WHITE WIRES
3 GREEN
WIRES
Single Switch Wiring
1 BLUE WIRES &
LIGHT SWITCH WIRE
2 WHITE WIRES
2 BLACK WIRES
3 GREEN WIRES
Dual Switch Wiring
Step 2. Trim excess motor wires, leaving at least 6 inches
above the downrod. Strip 1/2-inch insulation from the end
of each wire using a wire stripper (available at your local
hardware store).
Step 3. Attach the fan wires to the ceiling xture outlet box
wiring by placing the bare ends of the wires side by side
and then securing with a wire nut. Test that the connection
is secure by pulling on the wire nut. Connect in this order:
• GREEN leads from mounting plate and downrod
assembly of fan to GROUND conductor of power source.
Secure with wire nut.
• WHITE wire from fan to white NEUTRAL wire in ceiling
xture outlet box. Secure with wire nut.
Dual Switch Wiring:
•eblackwirefromtheceilingtotheblackwirefrom
thefan
•ebluewirefromthefantothewireforthewall
switch
Single Switch Wiring:
•eblackwirefromtheceilingtotheblackandtheblue
wirefromthefan
16
17
1616
AcAdemy
17
AcAdemy
17
LIGHT FIXTURE INSTALLATION (OPTIONAL)
NOTE: If you are installing your fan without a light kit attached as below in Figure #1, continue to Step 9a. If you
have purchased an Academy Gallery Edition, skip this section and go to Step 10 on page 19.
Figure #1
Switch Housing Installation
Step 9a. Partially install two of the three switch
housing screws onto the switch housing adapter plate
as shown in Figure #1.
Step 9b. Thread the Molex Plug through the hole in
the center of the switch housing and align the two
keyholes with the two screws that were installed on
the switch housing adapter plate. Place the switch
housing over the two screws and rotate it clockwise
so that the two screws are holding the switch housing
as shown in Figures #2 and #3.
Step 9c. Align the screw hole on the switch housing
with the screw hole in the switch housing plate and
insert the third screw as shown in Figure #3. Then
tighten all three screws with the provided screwdriver.
SWITCH HOUSING AND END CAP INSTALLATION
SWITCH HOUSING HARDWARE (not to scale)
Switch Housing
Adapter Plate
Adapter Plate
Screws (4)
Cover Plate Cap
Cover Plate
Screw (1)
Figure #2
Figure #3
Phillips
Screwdriver
Cap Plug
Fandangle (2)
Switch Housing
Screws (3)
Figure #1
18
19
1818
AcAdemy GALLery
Figure #6
Step 9d. Plug the male Molex plug into the female
Molex plug, aligning color and letters.
NOTE: The Molex plug will only connect if the
letters and colors are matched on both plugs. Do
not force the plug together.
Figure #4
MOLEX
PLUG
SWITCH HOUSING AND END CAP INSTALLATION - CONT
Step 9e. Tuck all wires into the switch housing.
Figure #4.
Step 9f. Find the keyed slots on the switch housing,
and the notches on the adapter plate. Line these up
and assemble the adapter plate to the switch housing
with the 4 adapter plate screws. Figure #5.
Step 9g. Place the cover plate cap onto the adapter
plate and secure using the Cover Plate screw. Figure
#2
Step 9h. Line up the notches on the cap plug to
the slots in the cover plate cap and snap into place.
Figure #6.
Figure #5
LIGHT FIXTURE INSTALLATION
ACADEMY GALLERY ONLY
Step 10. If you have purchased a Academy Gallery ™ your fan comes with a light kit. Please follow the following
steps to install your light kit.
Lower Glass Light Kit
Switch Housing
Screw (3)
Lower Bulb (3)
Glass Cover
Finial
Switch Housing Screws
Molex Plug
Switch Housing Installation
Step 10a. Partially install two of the three switch
housing screws onto the switch housing adapter plate
as shown in Figure #1.
Step 10b. Thread the Molex Plug through the hole in
the center of the switch housing as shown in Figure
#2. Align the two keyholes with the two screws that
were installed on the switch housing adapter plate.
Place the switch housing over the two screws and
rotate it clockwise so that the two screws are holding
the switch housing as shown in Figures #2 and #3.
Step 10c. Align the screw hole on the switch housing
with the screw hole in the switch housing plate and
insert the third screw as shown in Figure #3. Then
tighten all three screws with the provided screwdriver.
Figure #1
Figure #3
Figure #2
SWITCH
HOUSING
SCREWS
20
21
2020
AcAdemy GALLery
LIGHT FIXTURE INSTALLATION
ACADEMY GALLERY ONLY - CONTINUED
LIGHT FIXTURE INSTALLATION
ACADEMY GALLERY ONLY - CONTINUED
Light Kit Installation
Step 10d Remove one of the three light kit screws from
the side of the light kit plate and loosen the other two
as shown in Figure #1.
Step 10e.To attach the light kit, connect the upper plug
connector from the motor to the lower plug connector
in the light kit.
Note:Bothplugconnectorsarepolarized
andwillonlyttogetheroneway.Makesure
theconnectorsareproperlyalignedbefore
connectingthem.Incorrectconnectioncould
causeimproperoperationanddamagetothe
product.
Step 10f.Align the key hole slots in the switch housing
with the screws installed in step 10d. Raise light kit to
the switch housing and rotate clock wise. Install third
screw into light kit. Then tighten all three screws with
the provided screwdriver.
Light Kit Screws
Figure #1
Figure #2
Figure #3
Note: IncompliancewithU.S.Federalenergy
regulations,thisceilingfancontainsa
wattagesaverthatrestrictsthelightkit
toamaximumof190Watts.Exceeding
thatlimitorthespecicationsonthe
lightsocketsmayresultinrehazardor
improperoperation.
LIGHT FIXTURE INSTALLATION
ACADEMY GALLERY ONLY - CONTINUED
Stem
Cover
Finial
Glass Adapter
Glass Installation
Step 10g Remove the three bulbs from their packaging,
and install into the light kit.as shown in Figure #1.
Note: When replaceing bulbs, only replace with
max 40 watt bulbs.
Step 10h.Raise the glass up to the glass adapter on the
bottom of the light kit and route the pull chains through
the center of the bowl.
Step 10i.Routethechainsthroghthecoverandslide
thecoverontothebottomoftheglass.
Step 10j.Screwthenialontothebottomofthelight
kitstemtosecuretheglassbowl.
Step 10k.Attachtheextrapullchainstothelightand
fanpullchainsusingthebreakawayconnector.
Figure #1
22
23
2222
AcAdemy
23
AcAdemy
23
Pull-chain switches on the fan control the fan
Using the fan control pull-chain switch: Fan off at start.
First pull: fan ON, High speed
Second pull: Medium speed
Third pull: Medium Low speed
Fourth pull: Low speed
Fifth pull: Fan OFF
Direction of blade rotation is controlled by the reverse
pull chain on the side of the switch housing. No changes
in household wiring are required.
FAN OPERATION
FAN AND LIGHT OPERATION (GALLERY EDITION ONLY)
FAN PULL CHAIN
SWITCH
REVERSE PULL CHAIN
SWITCH
FAN PULL CHAIN
SWITCH
LIGHT PULL CHAIN
SWITCH
Pull-chain switches on the fan control the fan and lights.
Using the fan control pull-chain switch: Fan off
at start.
First pull: fan ON, High speed
Second pull: Medium speed
Third pull: Medium Low speed
Fourth pull: Low speed
Fifth pull: Fan OFF
The sequence of Light pull chain as follows:
Light off at Start.
No changes in household wiring are required.
To Change Airflow Direction
Turnthefanoandletitcometoacompletestop.Slidethe
reversingswitchonthefantotheoppositeposition.Restart
fan.
Reversing
Switch
TROUBLESHOOTING TIPS
Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance.
PROBLEM POSSIBLE REMEDIES
Fan wobbles or shakes excessively • Be sure the canopy pin is set properly into the slot on the ball.
• Check that the bladeholders have not been bent during installation and the blades
are balanced.
• The hanger bracket and/or the ceiling outlet are attached too loosely. Make sure
the hanger bracket is attached tightly to the ceiling outlet box and the downrod
assembly is secured rmly.
• The downrod is attached to the downrod base too loosely. Make sure all the
screws are securely tightened.
• Install the provided balancing kit.
Fan is noisy during operation • Tighten the canopy screws and mounting plate assembly. Make sure the wire
nuts inside the canopy and switch housing are not touching the metal parts and
that they have not fallen off the wire splices. Tighten as necessary.
• Tighten the blade holders to the direct drive motor and the blades to the bladeholder
screws.
• Make sure all the screws in the motor housing are snug but not overly tight.
• Check and tighten the light xture retaining screws, glass shade screws, and/or
lightbulb(s).
Fan does not run on low speed • If fan is new, it may need to be “broken in.” Run at high speed for several days.
Fan Finishes
• For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the nish.
• A vacuum cleaner brush nozzle can remove heavier dust.
• Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly
dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as these will damage the
nish.
Blades
• Wood-nish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of furniture polish may be
applied for added protection and beauty.
• For painted and high-gloss blades, surface smudges or an accumulation of dirt and dust can be removed easily using a
mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents
as these will damage the nish.
No Need for Lubrication
• Never lubricate this fan! The precision motor at the heart of your Casablanca fan features sealed bearings that are
lubricated for life.
• Do not attempt to oil the motor.
CARE RECOMMENDATIONS
242424
PRODUCT SPECIFICATIONS
Model Name: Academy
Model Number: C38UxxxK
Dimensions: A = 12.0
B = 14.5
C = 3.0
D = 13.7
E = 6.7
Weight: 28 lbs.
Model Name: Academy Gallery
Model Number: C38GxxxK
Dimensions: A = 12.0
B = 19.3
C = 3.0
D = 13.7
E = 6.7
Weight: 32 lbs.
Motor:
172mm x 20mm Direct Drive
Blade Span With: 54"
Blade Pitch: 14°
No. of Blades: 5
Airow: 5878 cfm
Electricity Use: 75 watts
Airow Efciency: 79 cfm/watt
Motor:
172mm x 20mm Direct Drive
Blade Span With: 54"
Blade Pitch: 14°
No. of Blades: 5
Airow: 5878 cfm
Electricity Use: 75 watts
Airow Efciency: 79 cfm/watt
Fan Finishes
• For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the nish.
• A vacuum cleaner brush nozzle can remove heavier dust.
• Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and
slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as
these will damage the nish.
Blades
• Wood-nish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of
furniture polish may be applied for added protection and beauty.
• For painted and high-gloss blades, surface smudges or an accumulation of dirt and dust can be removed
easily using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never
use abrasive cleaning agents as these will damage the nish.
No Need for Lubrication
• Never lubricate this fan! The precision motor at the heart of your Casablanca fan features sealed bearings
that are lubricated for life.
• Do not attempt to oil the motor.
Changing Lightbulbs
• Be sure to turn the power to OFF at the wall switch or circuit breaker before changing lightbulbs.
• Replace bulbs with the same type as you removed from the light xture.
• The maximum wattage rating for this fan’s light kit is 120 watts.
CARE RECOMMENDATIONS
FOR QUESTIONS OR TO LOCATE THE NEAREST CASABLANCA AUTHORIZED
SERVICE CENTER CALL TOLL FREE: 18882272178
OR VISIT US ON THE WEB AT: WWW.CASABLANCAFANCO.COM
/
