Haier HM-G552-FL User manual

·Please read the instructions carefully before use

·Haier reserves the right to explain the instructions

·The pictures are for reference only

UserManual

4G Smart Phone

Model:

G7lite

HM-G552-FL

Haier Europe Trading SRL

http://www.haier.com

3-5 Rue des Graviers, 92200, Neuilly-sur-Seine, France

Safety Cautions

4

7

8

10

12

14

16

17

18

23

25

27

28

31

34

35

37

38

41

42

Trouble Shooting

52

MobilePhone-UserManual

1

Knowing Your Phone

5

1

4

6

7

2

3

89

12

11

13

10

15 14

MobilePhone-UserManual

2

MobilePhone-UserManual

3

Removing the back cover

You must remove the back cover to install 4G LTE RUIM card,

SIM card and SD card. Hold the lower half of the phone with

battery cover upwards, and lift the bottom of the battery

cover, then the battery cover can be removed.

MobilePhone-UserManual

4

●Please turn the phone oﬀ before open the battery to

Caution

prevent damage.

●Please be careful when opening the back cover, follow it

accordingly to prevent damage.

Inserting the RUIM and SIM Card

You must insert SIM card on the phone to enjoy and enable

all the features. Your card contains all your subscription

information.

Insert 4G LTE RUIM and SIM card with the metal contacts

facing down and the cut corner is aligned with the cutting on

the slot.

●If SIM card is not installed, or there are errors in the

insertion, or the card is damaged, “No service notiﬁcation

will appear on the screen after your phone is powered on.

●If the PIN is enabled you need input the PIN number to

unlock it before you contrast using the phone.

●The GSM function will not work if SIM card is not present.

MobilePhone-UserManual

5

Inserting SD Card

Insert Mic r o SD Card with the metal contacts facing down

and the cut corner aligned with that of the slot.

●Please insert or remove the Micro SD Card when the

phone is powered oﬀ, or the Micro SD Card or the phone

might get damaged and the data on the Micro SD Card

could be lost.

Micro

SIM 1

Micro

SIM 2

TF card

MobilePhone-UserManual

6

Caution

●You might need to restart your phone after setting the

storage to SD-Card or when inserting an SD-Card.

Installing the battery

You must install and charge the battery to use your phone.

Insert the ridge at the top of the battery into the base of the

phone, make sure to touch the metal contact on the phone,

then push the battery down and snap it into place.

●Do not forces to turn the phone back on over and over if

the battery is too low, it might cause damage to the phone

and the battery.

●Please turn the phone oﬀ before open the battery to

prevent damage.

Note:

Caution

Your phone is designed to be used only with the original

batteries and chargers. The use of other batteries or

chargers is not recommended it may cause damage to your

phone and the warranty will be void.

MobilePhone-UserManual

7

Removing the battery

Make sure your phone is powered oﬀ before taking out the

battery to prevent data loss from the phone.

Charging the battery

New batteries are shipped partially charged. Before you can

use your phone, you need to charge the battery. Some

batteries will have best performance after several full

charge/discharge cycles, follow the instruction bellow:

MobilePhone-UserManual

8

1C onnect data cable and charger, plug one end into your

phone’s data port.

2P lug the other end of the charger into the appropriate

electrical outlet (100~240V AC).

3When your phone indicates that the battery is fully

charged, remove the charger.

Notes:

●The battery is removable, please properly install them to

prevent damage, and use the original battery and charger

●The battery can discharge gradually even when your

phone is powered oﬀ. If the battery is drained for a long time,

the information stored in the phone could possibly be lost.

●Even when you are not using the phone, it would be best to

charge your phone periodically to keep it away from draining.

●If the battery is charged after draining, the phone cannot

be turned on. The battery needs to be charged for a while,

after wardthen the phone will go to power-oﬀ charging

mode and you can turned on the phone.

●You need longer charging period with the lower voltage.

●Recommening do not operate phone during charging.

●The normal charge temperature is during 0⁰C- 40⁰C.

● Please avoid prolonged charging when the battery is full.

MobilePhone-UserManual

9

Turning on and oﬀ the phone

To turn on the phone:

Press and hold Power key for more than 3 seconds to turn

on your phone.

Turn oﬀ the phone:

Press and hold Power key to pop up option menu, select

“Power oﬀ”. If it is powered oﬀ you can not receive, make a

call or do other operations.

Get Started

Set up your phone

The ﬁrst time you turn on the phone, you'll see a Welcome

screen.

●To choose a diﬀerent language, press .

●To set up your phone, press and

f

oll

ow the instruction.

●You need to connect to an active network or WI-FI to

proceed.

There will be series of screens takes you through the setup

process. Setup complete, click “NEXT” to enter home

screen.

MobilePhone-UserManual

10

As you go through the setup screens, you have the option

to skip some steps. Then input your name allows your

phone to personalize some apps.

Connection Mode

You can select the connection mode on phone as USB

storage, Media device (MTP), Camera (PTP) and Charging

when your phone is connected to PC via Data Cable. By

holding the status bar with your ﬁnger, and drag it

downward, then you will see the Connection mode on

notiﬁcation panel. Touch it then it will open the option as

picture below, then you can select it as desired.

MobilePhone-UserManual

11

●The USB MTP might not work on Mac OS due to the

limitation and might required 3

rd

party application on the

Mac Computers for the MTP function.

Wi-Fi

Connecting to the Internet using Wi-Fi

Connecting to a Wi-Fi nectwork

Connect to a Wi-Fi network to access the Internet on your

device.

●To prevent unauthorized access to your personal data and

ﬁnancial information, always exercise caution when

connecting to public Wi-Fi networks.

1 .Go to Settings .

MobilePhone-UserManual

12

2 . Select Wi-Fi and turn on the Wi-Fi. Your device will display

a list of available Wi-Fi networks.

●Refresh the list: press

press

and then select “ Refresh” to

refresh the list of available Wi-Fi networks.

●Manually add a network: , and select “ Add

network“. Follow the onscreen instructions to enter the

network name and pass word manually.

3. Select the Wi-Fi network you want to connect to:

●If the Wi-Fi network does not require a password, your

device will connect automatically.

●If the network is protected, enter the password when

prompted and touch Connect.

Network and Sharing

Connecting to a Wi-Fi network using Wi-Fi Protected Setup

(WPS)

WPS allows your device to connect to a WPS-enabled router

without entering a password.

1. Go to Settings.

2 . Select Wi- Fi and switch on Wi-Fi.

3.

> Ad

vanced. There are two options:

●Select WPS Push Button.

MobilePhone-UserManual

13

Press

●Select WPS Pin Entry to generate a PIN, and then enter the

PIN on the router.

Bluetooth

1. Go to Settings

2. Select Bluetooth and switch on Turn on Bluetooth.

Ensure that the device you want to pair with is visible.

3. Select the device you want to pair with and follow the

onscreen instructions.

Unpairing Blue

Connectingto other device using Bluetooth

Enabling Bluetooth and pairing with other device

tooth devices

Transferring data using Bluetooth

1. Go to Settings .

2. Select Bluetooth and switch on Turn on Bluetooth.

3. Press the icon on the paired device name and select

FORGET.

Using Bluetooth to share ﬁles

Network and Sharing

Ensure that Bluetooth is enabled on both devices and that

both devices are visible.

MobilePhone-UserManual

14

1. Select the ﬁle(s) you want to share and press

>select Bluetooth. Your device will search for available

Bluetooth devices.

2. Select the receiving device.

3. On the receiving device, select Accept from the popup

dialog to accept the ﬁle transfer request. Open the

notiﬁcation panel to view the ﬁle transfer progress.

By default, received ﬁles are saved to the Bluetooth folder in

Files.

Sharing photos and videos with Bluetooth

When viewing photos or videos in full screen, you can share

content rapidly using Bluetooth.

Ensure that Bluetooth is enabled on both devices and that

both devices are visible.

1 Go t o Gallery.

2 Select the photo or video you want to share and open it in

full screen view. Press > Bluetooth to share the ﬁle. Your

device will search for nearby available Bluetoothdevices.

3 Select the receiving de vice.

4 On the receiving device, select Accept from the popup

dialog to accept the ﬁle transfer request. Open the

notiﬁcation panel to view ﬁle transfer progress.

By default, received ﬁles are saved to the Bluetooth folder in

Files.

Bluetooth settings

MobilePhone-UserManual

15

Renaming your device

Making your device visible

When you enable Bluetooth, your device model is used as

the default device name. To makeyour device easier to

identify, you can change the device name.

1. Go to Settings.

2. Press >Rename this d evice.

3. Enter a new name, and then touch Save.

1. Go to Settings.

2. Select Bluetooth and then switch on Bluetooth, make

your device visible to other Bluetooth devices.

Dialing

Press to enter dialer interface on idle screen or main

menu screen, input phone number and to make a

call, press the End button. If you make a mistake, you can

. to delete the number or hold it to delete all numbers

before the cursor.

During a call, you can do the following:

1. to open the dial pad.

MobilePhone-UserManual

16

press

Press

2. to enable or disable the loud speaker function.

3. to enable or disable your microphone.

4. on hold when use GSM card to call.

5. and then select Add call to add a call.

6. to end the call.

Messaging

Send and receive messaging

Create text messaging

Messaging icon to open the program.

to create message.

Input receiver’s phone number and edit contents.

For phone number:

1. You can click the keyboard to input number directly.

MobilePhone-UserManual

17

Press

2. You can select number from contacts. to open

your contact list and choose a contact or contact group.

3. You can select several numbers to send.

4. You can send multimedia message and attach the ﬁle by

icon.

or audio as you desired.

5.You can send message by SIM1 or SIM2 by pressing .

Notes:

If the message editing is interrupted by incoming calls, alarm

clock, powering oﬀ, the entered texts will be saved

temporarily.

Contacts

Creating a contact

1. Open Contacts .

2.

3. In the options menu, select a location to save the contact.

The number of contacts you can store on your device

depends on the size of your device's internal storage. The

number of SIM card contacts you can store depends on

your SIM card's storage capacity.

MobilePhone-UserManual

18

Then you can send the pictures, video

Press

press

Press .

4. the contact's proﬁle picture to choose a photo.

Enter the contact's name, company, phone number and

other contact information. The contact's photo will be

displayed when the contact calls you. Other contact

information such as company name and job title will also be

displayed.

You can also add phone numbers, email addresses, and

other contact information in to you rcontacts in call log,

Messaging or Email.

Importing and exporting contacts

Importing contacts from a storage device

1. Open Contacts.

2. >Import/Export >you can choose the location

where the contact storaged. Then click Next.

3. Then you can choose the location where you want to

import to.

Then click Next.

4. Select one or more .vcﬃles, and then click OK.

Managing contacts

Editing a contact

MobilePhone-UserManual

19

Press

Page is loading ...

Haier HM-G552-FL User manual

This manual is also suitable for

Haier HM-G552-FL User manual

Related papers

Other documents