Start Here
Unpack Your DV2130
• DVD+VCR
• Remote control
• 1.5V AAA batteries (2)
• RF (Radio Frequency) Antenna cable
• RCA cable for Audio/Video connections
• User’s guide
• Read Me First/
Quick Reference Guide
• Warranty registration card
Insert Batteries
1 Remove battery cover.
2 Insert two 1.5V AAA batteries, paying
attention to the correct polarities (+/–).
3 Replace cover.
• CD-ROM, CD+G, and CD-i discs cannot be
played on this DVD player.
Q uestions?
O ur Aw ard-W inning Customer
Service Professionals are
Ready to Help!
O r Check O ur
Website!
www.govideo.com
Call U s!
1-800-736-7679
E -M ail Us!
customerservice@govideo.com
DO N O T R E TU RN TH IS
PR O DUCT TO TH E STO R E !
T
hank
You!
For Fast, Friendly
Service
For a Prompt R e ply
For the Latest FAQ s
STOP
Antenna/Cable TV
DVD+VCR
Television
RCA Audio/Video
Cable
RF Antenna
Cable
DV2130
Use
r's Gu
i
d
e
POWER EJECT
TV MUTE DISPLAY
TV
REW FF
PLAY/PAUSESTOP
ENTER
CLEAR
LAST CH REPEAT
R
E
T
U
R
N
S
E
T
U
P
S
K
I
P
/
F
.
A
D
V
T
V
V
I
E
W
SELECT
+
V
O
L
U
M
E
C
H
A
N
N
E
L
1
2
3
4
5
6
7
8
9
0
100+
DVD
AUDIO
3D SOUND TV/VCR
DISC MENU
SUBTITLE MODE ANGLE MARK
TRACK-
VCR
AUTO
REC
SP/SLP
TIMER SEARCH/IDX
TRACK+
SHUTTLE
:: Basic Connections
To get started, you will need to connect the DVD+VCR to your TV and run Auto Setup. Auto
Setup will automatically search for channels and then set your DVD+VCR’s internal clock.
1 Connect Antenna to DVD+VCR Connect an indoor/outdoor antenna or wall outlet
antenna cable to the IN (FROM ANT.) jack on the rear panel.
2 Connect DVD+VCR to TV Choose one of the following methods:
a. RF Connection Using the supplied RF antenna cable, connect the OUT
(TO TV) jack on the back panel of the DVD+VCR to your TV’s Antenna Input.
b. Line Connection Using the supplied RCA-type audio/video cable (red,
white, yellow), connect the LINE OUT jacks on the back panel of your DVD+VCR
to your TV's Line In jacks. If your TV is equipped with RCA jacks, it is
better to use the Line Connection method.
3 Plug In Plug the DVD+VCR power cable into a standard 120V/60Hz wall outlet.
Avoid pressing any buttons on the remote control or on the unit during Auto Setup. While
your DVD+VCR is running Auto Setup, “AUTO” will blink on the front panel display. When
Auto Setup is complete, the current time will be displayed on the front panel display.
4 Turn On Your DVD+VCR Press the POWER button on the remote control or front
panel of the unit.
5 Turn On Your TV Press the POWER button on your TV.
6 Set the TV to Channel 3, 4 or Line Use the same channel you selected in Step 2
above. If you are using the Line Connection method, set your TV to its Line Input.
• You must use either the Standard RF or Line connection between your TV and
DVD+VCR, even if you plan to use the S-Video or Component Video Output for
improved DVD picture quality.
• The S-Video and Component Video Outputs are for DVD playback only!
• See the User's Guide for advanced connections.
To Play a VHS Tape
1 Insert a VHS tape into the VCR deck. The DVD+VCR will power on automatically when you insert the tape.
2 Press PLAY to begin playback.
To Play a DVD or CD
1 Press EJECT on the remote control or front panel to open the disc drawer. The DVD+VCR will power on automatically when you
open the disc drawer.
2 Place the disc in the drawer with the label side facing up. If the disc has two sides, place the disc with the desired side facing up.
3 Press EJECT again to close the disc drawer.
4 Press PLAY to begin playback. Many discs will begin playback automatically when the disc drawer closes.
POWER EJECT
TV MUTE DISPLAY
TV
REW FF
PLAY/PAUSESTOP
ENTER
CLEAR
LAST CH REPEAT
R
E
T
U
R
N
S
E
T
U
P
S
K
I
P
/
F
.
A
D
V
T
V
V
I
E
W
SELECT
+
V
O
L
U
M
E
C
H
A
N
N
E
L
1
2
3
4
5
6
7
8
9
0
100+
DVD
AUDIO
3D SOUND TV/VCR
DISC MENU
SUBTITLE MODE ANGLE MARK
TRACK-
VCR
AUTO
REC SP/SLP
TIMER SEARCH/IDX
TRACK+
SHUTTLE
• If the DVD has a disc menu, or more than one title, the disc menu may appear.
If so, press / and / to highlight menu items, then press SETUP/ENTER to
make selections.
©2003 GoVideo, Inc. All rights reserved.
:: Basic Controls
Two Decks, One Set of Controls!
DVD Button – Press to control the DVD deck. All deck control keys
and blue labeled buttons will operate the DVD player.
VCR Button – Press to control the VCR deck. All deck control keys
and red labeled buttons will operate the VCR.
TV Button – Press to control your TV. Certain TV functions,
including POWER, VOLUME, CHANNEL, INPUT and TV MUTE
will control your TV. See the User's Guide to program the remote to
control many brands of television.
:: Basic Disc Playback
:: Basic VCR Playback
• If the tape is missing the record safety tab and Auto Play is turned
on, the tape will begin playing automatically.
TV View Button – Press to change your
on-screen view. Each press will select a
different input source: DVD, VCR, TV,
Line 1 (rear A/V input), or Line 2 (front
A/V input).
PLAY
EJECTEJECT
PLAY
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Go-Video DVR4300 Start Here
-
Go-Video DVR5100 User manual
-
Samsung DVD-V2000 User manual
-
-
Sonic Blue DVR4300 User manual
-
-
-
-
-
