Anleaf Technologies AP300W User manual

Brand: Anleaf Technologies

Model: AP300W

Category: Power extensions

Type: User manual

Anleaf Technologies Co., Ltd.

No.68-6, Zhongxiao Street, Tuku Township, Yunlin County 63359, Taiwan

website: www.anleaf.com.tw / e-mail: [email protected]

USER GUIDE

Portable Solar Power Generator

Model : AP300W

H.M.I. (Human-Machine Interface) Configuration:

Item

Master switch// LED : Power On/Off

AC O/P Switch//LED

PV I/P -1: DC sockets for 5.0x2.1mm plug ; 8A

AC O/P sockets: Pure Sine Wave

PV I/P-2 : terminal block for 25AMax (total)

USB DC O/P socket: 5VDC

AC I/P// LED :100V~240Vac/ 50~60Hz

Battery Storage Display Switch

Charge status LED : Charge status of system

Battery Storage LED Display

DC O/P Switch //LED

Carrying handle

Car cigarette O/P socket: 12VDC of battery

Trolley and Brake

DC O/P socket: 24V/70W

Equipment Introduction:

1. Logic Chart for Solar Power Box and PV Panel

2. Main Components:

2.1. The solar power panel applies to 12VDC energy storage battery system.

2.2. PV charge/discharge controller owns 12VDC/25A input and 12V/30A output.

2.3. Built-in constant current VAC/VDC & C.C Mode AC/DC power supply unit.

2.4. BMS Battery (LiFePO4 battery management system).

2.5. LiFePO4 battery (of 4 cells in serial connection with 12.8V.DC nominal volts).

2.6. DC/AC inverter and 5VDC-DC USB port.

2.7. DC/DC converter.

2.8. The LED display of battery storage shows the voltage as power energy of battery.

Specifications:

Item

Condition

Value

Unit

Input

Solar Panel

Input Power

Terminal block(total)

80Wp(default option), Vmp＜23V；Imp=25A

20~ 360

DC plug (each)

80Wp(default option) Imp<8A, Vmp＜24V

20~120

AC power socket

AC100~240V//50~60Hz

100~240

Vac

Ratings for solar charge controller

I/P:12V/25A max; O/P:12V/30A max

VDC

Energy storage battery

LiFePO4 battery (3 options)

12.8V/20Ah // 30Ah // 40Ah (default )

20//30//40

AC Output

AC output power

300W/600VA, 220V//110V/50/60Hz

300

Output wave

Pure Sine Wave

YES

Efficiency

≧85%

85%

Overload / Short circuit protection

Circuit control with self-recovery fuse

YES

Overload ability

100%≦Load≦500% for 3S; 500%≦Load 1S

DC Output

output

Cigarette lighter socket

9.6VDC~14.60VDC/6A max

VDC

DC plug

24VDC/3Amax (customized)

24V/3A

VDC/A

USB port

5V500mA

5/500

V/mA

Others

Working Temperature

-20~75

℃

Ambient Temperature

-30~55

℃

Storage Temperature

Battery＜35℃ recommended

℃

Weight (kg)

13 kgs (with battery of 12V x 40Ah)

Noise (1M)

＜45dB

Output Outlet Configuration

Vac Universal output socket × 2

USB Port ×1 VDC cigarette lighter socket ×1

VDC output plug x1

Relative Humidity

5~90% ,W/O Moisture

Dimension

380 x 220 x 260

Altitude

under 3000M

3000

Feature:

1. Application to PV panel from 20w to 360w, but the input current is limited at 25A max.

2. BMS auto protects the panel & battery from over-charging & over-discharging, short-circuit, low voltage,

overheating, reverse connection, inrush voltage and over-load.

3. Hybrid input power source: AC Source and Solar Power Source.

4. Working as power supply system, DC/AC UPS or a secondary battery.

5. Equipped with battery LiFePO4 and built-in protection system.

6. The device can meanwhile be working on charging and discharging mode.

7. Auto detects the storage of battery, if the power energy of battery is under low level; the LED light will

flash continually.

8. The device owns high efficiency on charging mode.

9. PV Power Box sets the multi-port terminal blocks with a parallel connection.

Caution:

1. If assembling, please note that the red Y-type terminal of PV panel connects up the anode (+) and the

black or blue terminal block connects up the cathode (-) of solar power box.

2. Turns off the electric power before cleaning the device; please clean by dry cloth only.

3. Please check the LED display of battery storage before using, if it is low power level, please recharge.

4. Please turn off the electric power if un-using, it can be avoided the battery power to flow away.

5. Turns on the electric power without a load, please note that the high voltage still runs on AC outlet.

6. Please avoid the environment of high temperature when the battery is using.

7. Do not un-screw the solar power box except the qualified engineer.

8. To avoid the water or anything into the device.

9. Do not connect with additional battery to extend the power of device.

10. If user meets out of right operation or other operating problems, please turn off the electric power.

11. If the device is frequently extended on limit-use, it will reduce the product life.

How to Use:

1. Charging:

1.1. AC I/P as an Auxiliary Power Source

1.1.1. Turns on master switch (On/Off switch).

1.1.2. Connects up the electric power.

1.1.3. If the power energy of battery is on charge completion, the LED light will be constant light otherwise

it will be flashing continually.

1.2 Solar Power Source DC I/P

1.2.1. Turns on master switch (On/Off switch).

1.2.2. Y-type terminals of PV panel connects up the terminal block of Solar Power Box and also check if

everything is right for the red cable terminal to the positive (+) and the black or blue cable terminal to the

negative (-) of the terminal blocks on the solar power box.

1.2.3. In using the DC plug, user should connect the male DC cable of PV panel with the female DC socket.

1.2.4. If the power energy of battery is on charge completion, the LED light will be constant light otherwise

it will be flashing continually.

2. The Status of Battery Storage:

In main quiescent mode, user turns on the spring switch of battery that will know the power status via LED

display in charging mode (SoC) and will also know how voltage the battery storage in its occupation is. In

dynamic mode, user should pay attention to the operating temperature of battery in discharge current so as

to avoid affecting the battery energy storage directly. The following table is made according to the charge

voltage (SoC) and storage of battery.

Battery Storage

0%~15%

15%~35%

35%~55%

55%~75%

75%~100%

Voltage Level

9.6V~

12.2V~

12.6V~

12.8V~

13.2V~

Efficient load

AC/DC

Green LEDs

1~2

2~3

4~5

Orange LEDs

1~3

Red LEDs

1~2

2.1. High Power Storage Battery

If the LED indicates green light, the power of battery shows in full level and the voltage is above 12.6V

usually.

2.2. Low Power Storage Battery

If the LED indicates yellow light, the battery power shows in low level, then user can choose the DC

output; the battery could be used for some time.

2.3. Protection for Low Voltage

If the red LED light is flashing, the Under-Voltage-Protection (UVP) will be working at once. When the

UVP is working, the protection system will reject any operation and auto checks up the status of battery

storage. At this stage, if the voltage is under 9.6V, the LED display will auto shut off.

3. Discharging:

The most output is 360W including AC/DC discharging at the same time. If the master switch is

turned on, the device will be ready for operation; user should pay attention to the status of battery power.

3.1. AC Discharge (300W/600VA)

In using AC output, please turn on the AC power switch. User should care about the input ratings of load

& also check what the voltage is (110VAC or 220VAC). Note: 5VDC USB socket is set up at this unit

with a rating of 5VDC/500m A.

3.2. DC Discharge (Constant DC output socket & Car cigarette output socket is 12VDC/6A)

In using DC output, please turn on the DC power switch. User should care about the input ratings of load

& check if the DC rating is less than the power consumption. Please refer to the DC outlet rating as

specification.

Trouble Shooting:

1. If AC load cannot keep working, please check up the solar power bank according to the following

procedures:

1.1. Please check if the rated power of the load is ＜300W ?

1.2. If the rate is the same as ＜300W condition, please check whether the voltage of battery storage has

got a “Duty Cycle”. Usually High Electric Potential will drive the AC load, but if an AC load gets higher

wattage, it will absorb higher current draw and also work continually, the UVP will be started to protect the

system and auto shut down. In this case, please check whether DC outlet is working normally, if so, please

re-charge the battery.

1.3. If the LED display of battery storage shows the status of full or normal power however the AC output

cannot work, the UVP will be started due to the single cell volt may be dropped to 2.4V.

If the single cell gets such problem, it could be aging, we suggest that you should change into new battery

or send it back for investigation.

2. Instantaneous over-load

The total output of solar power bank is 300W with two AC output sockets. If the two AC outputs gets the

value of loads which are more than 150 watts meanwhile, the protection system will auto-cutoff the electric

power to protect the inverter. The solution is to run 1st load first and again run 2nd load.

3. The LED display of battery storage to be flickering by heavy load

When it is full load, the high current will be output & the voltage will be quickly declined. The power light

will be rapidly decreased to reflect on the charge sheet until the low pressure protection (UVP) to be started

and auto-cutoff the electric power, this event is regarded dynamic "Floating Voltage".

Another condition, if there is one or two green lights that still indicates with considerable power and gets

overload, it will be happened as above statement. The best solution is to re-charge the battery up to full

power.

4. Both voltage rating and device do not match up

If the device cannot work or be burnt, the problem is that both nominal voltages cannot match up. Please

recheck the specification of power supply unit and solar power bank.

5. Reduction of working wattage hour under different discharge current

In the same condition for batteries, the voltage maybe offer different power energy and discharge current,

this is the electrochemical characteristic of a battery. Therefore, the solar power box should use under 0.5

discharge current (0.5 Ca) of battery capacity.

6. Overheat protection

Auto- cutoff for overheating (up to 75℃). Please refer to the specifications.

7. How to keep high voltage in free

If the battery is un-used, please keep the voltage of battery about 60% and charge/discharge once for 3

months each.

8. How to restart the system after over-current protection.

Usually there is electronic protection for over-current or short-circuit at each input/output port. If an

overload or short circuit be happened at any port, it must be removed before the system has returned to

work.

Anleaf Technologies AP300W User manual

Brand: Anleaf Technologies

Model: AP300W

Category: Power extensions

Type: User manual

Download PDF

report

Anleaf Technologies AP300W User manual

Anleaf Technologies AP300W User manual

Other documents