Toro 22in Recycler Lawn Mower User manual

Brand: Toro

Model: 22in Recycler Lawn Mower

Category: Lawnmowers

Type: User manual

Toro 22in Recycler Lawn Mower: Experience effortless lawn care with its powerful engine, durable construction, and versatile features. Tackle large areas efficiently with its 22-inch cutting width, while the Recycler mulching system finely cuts and returns nutrients to your lawn, promoting a lush, healthy yard. Its blade control bar allows for easy height adjustment, and the sturdy design ensures long-lasting performance.

Form No. 3358-343 Rev A

22in Recycler® Lawn Mower

Model No. 20075 —Serial No. 270000001 and Up

Model No. 20076 —Serial No. 270000001 and Up

Model No. 20076A —Serial No. 270000001 and Up

Operator's Manual

Introduction

R ead this infor mation carefully to lear n ho w to operate and

maintain y our product properly and to a v oid injur y and

product damag e . Y ou are responsible for operating the

product properly and safely .

Y ou ma y contact T oro directly at www .T oro .com for

product and accessor y infor mation, help ﬁnding a dealer ,

or to register y our product.

W henev er y ou need ser vice , g en uine T oro par ts , or

additional infor mation, contact an A uthorized Ser vice

Dealer or T oro Customer Ser vice and ha v e the model and

serial n umbers of y our product ready . Figure 1 identiﬁes the

location of the model and serial n umbers on the product.

Figure 1

1. Model and serial number plate

W rite the product model and serial n umbers in the space

belo w:

Model No.

Serial No.

T his man ual identiﬁes potential hazards and has safety

messag es identiﬁed b y the safety aler t symbol ( Figure 2 ),

whic h signals a hazard that ma y cause serious injur y or

death if y ou do not follo w the recommended precautions .

Figure 2

1. Safety alert symbol

T his man ual uses 2 w ords to highlight infor mation.

Impor tant calls attention to special mec hanical infor mation

and Note emphasizes g eneral infor mation w or th y of special

attention.

Warning

CALIFORNIA

Pr oposition 65 W ar ning

T he engine exhaust fr om this pr oduct contains

chemicals kno wn to the State of Calif or nia to cause

cancer , bir th defects, or other r epr oducti v e har m.

Important: T his engine is not equipped with a

spar k ar r ester muf ﬂer . It is a violation of Calif or nia

Public R esource Code Section 4442 to use or operate

the engine on an y f or est-co v er ed, br ush-co v er ed, or

g rass-co v er ed land. Other states or federal ar eas may

ha v e similar la ws.

T his spark ignition system complies with Canadian

ICES-002

T he enclosed Engine Owner’ s Man ual is supplied

f or inf or mation r egarding the US En vir onmental

Pr otection Agency (EP A) and the Calif or nia Emission

Contr ol R egulation of emission systems, maintenance,

and w ar ranty . R eplacements may be order ed thr ough

the engine man uf actur er .

F or models with stated engine horse po w er , the g ross

horse po w er of the engine w as laborator y rated b y the engine

man ufacturer in accordance with SAE J1940. As conﬁgured

to meet safety , emission, and operating requirements , the

actual engine horse po w er on this class of la wn mo w er will

be signiﬁcantly lo w er .

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA

Safety

T his la wn mo w er meets or ex ceeds the CPSC blade safety

requirements for w alk-behind rotar y la wn mo w ers and the

B71.1 speciﬁcations of the American National Standards

Institute in effect at the time of production.

R ead and under stand the contents of this man ual

bef or e y ou star t the engine.

T he safety aler t symbol ( Figure 2 ) is used to aler t y ou to

potential personal injur y hazards . Obey all safety messag es

that follo w this symbol to a v oid possible injur y or death.

Improperly using or maintaining this mo w er could result in

injur y or death. T o reduce this potential, comply with the

follo wing safety instr uctions .

T he follo wing instr uctions ha v e been adapted from the

ANSI/OPEI standard B71.1-2003.

T his cutting machine can amputate hands and feet and

thr o w objects. F ailur e to obser v e the f ollo wing safety

instr uctions could r esult in serious injur y or death.

General Operation

• R ead, understand, and follo w all instr uctions on the

mac hine and in the man ual(s) before star ting .

• Do not put hands or feet near or under the mac hine .

K ee p clear of the disc harg e opening at all times .

• Only allo w responsible adults , who are familiar with the

instr uctions , to operate this mac hine .

• Clear the area of objects suc h as roc ks , wire , to ys , etc .,

whic h could be thro wn b y the blade . Sta y behind the

handle when the engine is r unning .

• Be sure the area is clear of b ystanders before operating .

Stop mac hine if any one enters the area.

• Do not operate mac hine barefooted or while w earing

sandals . Alw a ys w ear substantial footw ear .

• Do not pull mac hine bac kw ard unless absolutely

necessar y . Alw a ys look do wn and behind before and

while mo ving bac kw ard.

• Nev er direct disc harg ed material to w ard any one . A v oid

disc harging material ag ainst a w all or obstr uction.

Material ma y ricoc het bac k to w ard the operator . Stop

the blade when crossing g ra v el surfaces .

• Do not operate mac hine without the entire g rass

catc her , disc harg e guard, rear guard, or other safety

protecti v e devices in place and w orking .

• Nev er lea v e a r unning mac hine unattended.

• Stop the engine and w ait until the blade comes to a

complete stop before cleaning the mac hine , remo ving

g rass catc her , or unclog ging the disc harg e guard.

• Operate mac hine only in da ylight or g ood ar tiﬁcial light.

• Do not operate mac hine while under the inﬂuence of

alcohol or dr ugs .

• Nev er operate mo w er in w et g rass . Alw a ys be sure of

y our footing; w alk; nev er r un.

• Diseng ag e the dri v e system, if so equipped, before

star ting the engine .

• If the mac hine should star t to vibrate abnor mally ,

stop the engine and c hec k for the cause immediately .

Vibration is g enerally a w ar ning of trouble .

• Alw a ys w ear eye protection when operating mac hine .

• See man ufacturer’ s instr uctions for proper operation

and installation of accessories . Only use accessories

appro v ed b y the man ufacturer .

Slope Operation

Slopes are a major factor related to slip and fall accidents ,

whic h can result in sev ere injur y . Operation on all slopes

require extra caution. If y ou feel uneasy on a slope , do

not mo w it.

• Mo w across the face of slopes; nev er up and do wn.

Ex ercise extreme caution when c hanging direction on

slopes .

• W atc h for holes , r uts , bumps , roc ks , or other hidden

objects . Unev en ter rain could cause a slip and fall

accident. T all g rass can hide obstacles .

• Do not mo w on w et g rass or ex cessi v ely stee p slopes .

P oor footing could cause a slip and fall accident.

• Do not mo w near drop-offs , ditc hes , or embankments .

Y ou could lose y our footing or balance .

Children

T ragic accidents can occur if the operator is not aler t to

the presence of c hildren. Children are often attracted to

the mac hine and the mo wing acti vity . Nev er assume that

c hildren will remain where y ou last sa w them.

• K ee p c hildren out of the mo wing area and under the

w atc hful care of a responsible adult other than the

operator .

• Be aler t and tur n mo w er off if a c hild enters the area.

• Nev er allo w c hildren to operate the mac hine .

• Use extra care when approac hing blind cor ners , shr ubs ,

trees , or other objects that ma y bloc k y our view of a

c hild.

Service

Safe Handling of Gasoline

T o a v oid per sonal injur y or pr oper ty dama ge, use

extr eme car e in handling gasoline. Gasoline is

extr emel y ﬂamma ble and the v apor s ar e explosi v e.

• Extinguish all cig arettes , cig ars , pipes , and other sources

of ignition.

• Use only an appro v ed g asoline container .

• Nev er remo v e g as cap or add fuel with the engine

r unning . Allo w engine to cool before refueling .

• Nev er refuel the mac hine indoors .

• Nev er store the mac hine or fuel container where there

is an open ﬂame , spark, or pilot light suc h as on a w ater

heater or on other appliances .

• Nev er ﬁll containers inside a v ehicle or on a tr uc k or

trailer bed with a plastic liner . Alw a ys place containers

on the g round a w a y from y our v ehicle before ﬁlling .

• R emo v e g as-po w ered equipment from the tr uc k or

trailer and refuel it on the g round. If this is not possible ,

then refuel suc h equipment with a por table container ,

rather than from a g asoline dispenser nozzle .

• K ee p the nozzle in contact with the rim of the fuel

tank or container opening at all times until fueling is

complete . Do not use a nozzle loc k-open device .

• If fuel is spilled on clothing, c hang e clothing

immediately .

• Nev er o v erﬁll fuel tank. R e place g as cap and tighten

securely .

Exhaust contains carbon mono xide, an odor less,

deadl y poison that can kill y ou.

Do not r un the engine indoor s or in an enclosed ar ea.

General Service

• Nev er operate mac hine in a closed area.

• K ee p all n uts and bolts tight to be sure the equipment is

in safe w orking condition.

• Nev er tamper with safety devices . Chec k their proper

operation regularly .

• K ee p mac hine free of g rass , lea v es , or other debris

build-up . Clean up oil or fuel spillag e and remo v e

any fuel-soak ed debris . Allo w mac hine to cool before

storing .

• If y ou strik e a foreign object, stop and inspect the

mac hine . R e pair , if necessar y , before star ting .

• Nev er mak e any adjustments or re pairs with the engine

r unning . Disconnect the spark plug wire and g round

ag ainst engine to prev ent unintended star ting .

• Chec k g rass catc her components and the disc harg e

guard frequently and re place with man ufacturer’ s

recommended par ts , when necessar y .

• Mo w er blades are shar p . W rap the blade or w ear glo v es ,

and use extra caution when ser vicing them.

• Do not c hang e the engine g o v er nor setting or o v erspeed

the engine .

• Maintain or re place safety and instr uction labels , as

necessar y .

Safety and Instructional Decals

Important: Safety and instr uction decals ar e located

near ar eas of potential danger . R eplace dama ged

decals.

Manufacturer’s Mark

1. Indicates the blade is identied as a part from the original machine

manufacturer.

94-8072

104-7402

Model 20076 only

104-7953

Models 20076 and 20076A only

1. Warning—read the Operator’s Manual for information on charging the battery; contains lead; do not discard.

2. Read the Operator’s Manual.

104-7403

Model 20076 only

108-8192

Model 20076A only

105-1295

108-4791

Models 20076 and 20076A only

108-8117

108-8191

Model 20076A only

108-9751

Models 20076 and 20076A only

1. Engine—stop 3. Engine—start

2. Engine—run

112-8868

Setup

Important: R emo v e and discard the pr otecti v e

plastic sheet that co v er s the engine.

1. Installing the Blade Control

Bar

Install the blade control bar into the upper handle ( Figure 3 ).

Figure 3

2. Unfolding the Handle

F olding or unf olding the handle impr oper l y can

dama ge the ca bles, causing an unsafe operating

condition.

• Do not dama ge the ca bles when f olding or

unf olding the handle.

• If a ca ble is dama ged, contact an Authoriz ed

Ser vice Dealer .

1. Carefully mo v e the upper handle forw ard until the

handle halv es are in line and nest tog ether , and tighten

the handle knobs ( Figure 4 ).

Figure 4

2. Squeeze the lo w er handle tog ether and mo v e the handle

rearw ard until it clic ks into the operating position

( Figure 5 ).

Figure 5

3. Filling the Engine with Oil

Y our mo w er does not come with oil in the engine , but it

does come with a bottle of oil.

1. R emo v e the dipstic k ( Figure 6 ).

Figure 6

2. Slo wl y pour oil into the oil ﬁll tube until the oil lev el

reac hes the Full line on the dipstic k ( Figure 6 ). Do not

o v erﬁll. (Max. ﬁll: 20 oz., type: SAE 30W deterg ent

oil with an API ser vice classiﬁcation of SF , SG , SH, SJ ,

SL, or higher .)

3. Install the dipstic k securely .

Important: Change the engine oil after the ﬁr st 2

operating hour s ; change it y ear l y ther eafter . R efer

to Changing the Engine Oil.

4. Installing the Fuse

Models 20076 and 20076A onl y

Y our mo w er comes with a 40-amp fuse that protects the

electric star ter .

Important: Y ou cannot star t the mo w er with the

electric star ter or charge the batter y unless y ou install

the fuse.

1. Unclip both ends of the batter y co v er and remo v e it

( Figure 7 ).

Figure 7

2. Inser t the fuse into the fuse holder ( Figure 8 ).

Figure 8

Note: Y our mo w er comes with a fuse in the o wner’ s

pac k et and another fuse in the batter y bo x.

3. Install the batter y co v er .

5. Charging the Battery

Models 20076 and 20076A onl y

R efer to Charging the Batter y in the Maintenance section.

Product Overview

Figure 9

1. Cutting height lever 8. Fuel tank cap

2. Oil ll/Dipstick

9. Battery (not shown; models

20076 and 20076A only)

3. Recoil start handle 10. Air lter

4. Control bar lock 11. Washout port

5. Blade control bar

12. Primer

6. Self-propel drive bar 13. Spark plug

7. Ignition toggle switch (model

20075 only) or ignition key

(models 20076 and 20076A

only)

Figure 10

1. Grass bag

3. Battery charger (models

20076 and 20076A only)

2. Side discharge chute

Operation

Filling the Fuel Tank

Gasoline is extr emel y ﬂamma ble and explosi v e. A

ﬁr e or explosion fr om gasoline can bur n y ou and

other s.

• T o pr ev ent a static charge fr om igniting the

gasoline, place the container and/or mo w er

dir ectl y on the g r ound bef or e ﬁlling , not in a

v ehicle or on an object.

• Fill the tank outdoor s when the engine is cold.

W ipe up spills.

• Do not handle gasoline when smoking or ar ound

an open ﬂame or spar ks.

• Stor e gasoline in an appr o v ed fuel container , out

of the r each of childr en.

Fill the fuel tank with fresh unleaded regular g asoline from

a major name-brand ser vice station ( Figure 11 ).

Note: Nev er use methanol, g asoline containing methanol,

or g asohol containing more than 10% ethanol because the

fuel system could be damag ed. Do not mix oil with g asoline .

Important: T o r educe star ting pr oblems, add fuel

sta biliz er to the fuel all season, mixing it with gasoline

less than 30 days old.

Figure 11

Checking the Engine Oil Level

1. R emo v e the dipstic k, wipe it clean, and fully install the

dipstic k ( Figure 12 ).

Figure 12

2. R emo v e the dipstic k and c hec k the oil lev el ( Figure 12 ).

If the oil lev el is belo w the Add mark on the dipstic k,

slo wl y pour oil into the oil ﬁll tube to raise the oil lev el

to the Full mark on the dipstic k. Do not o v erﬁll. (Max.

ﬁll: 20 oz., type: SAE 30W deterg ent oil with an API

ser vice classiﬁcation of SF , SG , SH, SJ , SL, or higher .)

3. Install the dipstic k securely .

Adjusting the Cutting Height

Adjusting the cutting height may bring y ou into contact with the mo ving blade, causing serious injur y .

• Stop the engine and w ait f or all mo ving par ts to stop .

• Do not put y our ﬁnger s under the housing when adjusting the cutting height.

If the engine has been r unning , the muf ﬂer will be hot and can sev er el y bur n y ou. K eep a w ay fr om the hot

muf ﬂer .

Adjust the cutting height as desired. Set the front wheels to the same height as the rear wheels ( Figure 13 ).

Figure 13

Starting the Engine

Model 20075 onl y

1. Push the ignition tog gle switc h to the On (I) position

( Figure 14 ).

Figure 14

1. Ignition toggle switch

2. Fir mly push in the primer 3 times with y our thumb ,

holding the primer in for a second before releasing it

eac h time ( Figure 15 ).

Figure 15

Note: If the air temperature is belo w 55°F (13°C),

ﬁr mly push the primer in 5 times .

3. Pull the recoil star ter ( Figure 16 ).

Figure 16

4. If the mo w er does not star t in 1 or 2 pulls , press the

primer button 1 or 2 times and tr y star ting it ag ain.

Note: If the mo w er still does not star t, contact an

A uthorized Ser vice Dealer .

Starting the Engine

Models 20076 and 20076A onl y

1. Fir mly push in the primer 3 times with y our thumb ,

holding the primer in for a second before releasing it

eac h time ( Figure 17 ).

Figure 17

Note: If the air temperature is belo w 55°F (13°C),

ﬁr mly push the primer in 5 times .

2. T ur n the ignition k ey ( Figure 18 ) (models 20076 and

20076A only) or pull the recoil star t handle ( Figure 19 ).

Figure 18

Figure 19

3. If the mo w er does not star t in 1 or 2 pulls (or within

5 seconds using the electric star ter), press the primer

button 1 or 2 times and tr y star ting it ag ain.

Note: If the mo w er still does not star t, contact an

A uthorized Ser vice Dealer .

Using the Self-propel Drive

T o operate the self-propel dri v e , simply w alk with y our

hands on the upper handle and y our elbo ws at y our sides ,

and the mo w er will automatically k ee p pace with y ou

( Figure 20 ).

Figure 20

Note: Y ou can self-propel the mo w er with the blade

eng ag ed or diseng ag ed.

Stopping the Engine

Model 20075 onl y

Push the ignition tog gle switc h to the Stop position ( Figure

21 ).

Figure 21

1. Ignition toggle switch

Stopping the Engine

Models 20076 and 20076A onl y

1. T ur n the ignition k ey to the Off position.

2. R emo v e the ignition k ey when y ou lea v e the mo w er .

Engaging the Blade

W hen y ou star t y our engine , the blade does not tur n. Y ou

m ust eng ag e the blade to mo w .

1. Pull the control bar loc k bac k ( Figure 22 ).

Figure 22

2. Pull the blade control bar to the handle ( Figure 23 ).

Figure 23

1. Blade control bar

3. Hold the blade control bar ag ainst the handle ( Figure

24 ).

Figure 24

Disengaging the Blade

R elease the blade control bar ( Figure 25 ).

Figure 25

Important: W hen y ou r elease the blade contr ol bar ,

the blade should stop within 3 seconds. If it does not

stop pr oper l y , stop using y our mo w er immediatel y and

contact an Authoriz ed Ser vice Dealer .

Checking the Blade Brake

Clutch Operation

Chec k the control bar before eac h use to ensure that the

blade brak e clutc h system is operating properly .

Using the Grass Bag

Y ou can use the g rass bag to perfor m an additional test to

c hec k the blade brak e clutc h.

1. Install the empty g rass bag on the mo w er .

2. Star t the engine .

3. Eng ag e the blade .

Note: T he bag should begin to inﬂate , indicating that

the blade is eng ag ed and rotating .

4. R elease the blade control bar .

Note: If the bag does not immediately deﬂate , the

blade is still rotating . T he blade brak e clutc h ma y be

deteriorating and, if ignored, could result in an unsafe

operating condition. Ha v e the mo w er inspected and

ser viced b y an A uthorized Ser vice Dealer .

5. Stop the engine and w ait for all mo ving par ts to stop .

Not Using the Grass Bag

1. Mo v e the mo w er onto a pa v ed surface in a non-windy

area.

2. Set all 4 wheels to the 2-3/4 inc h (7 cm) cut setting .

3. T ak e a half sheet of newspaper and cr umple it into a ball

small enough to g o under the mo w er housing (about 3

inc hes or 7.6 cm in diameter).

4. Place the newspaper ball about 5 inc hes (13 cm) in

front of the mo w er .

5. Star t the engine .

6. Eng ag e the blade .

7. R elease the blade control bar .

8. Immediately push the mo w er o v er the newspaper ball.

9. Stop the engine and w ait for all mo ving par ts to stop .

10. Go to the front of the mo w er and c hec k the newspaper

ball.

Note: If the newspaper ball did not g o under the

mo w er , re peat ste ps 4 through 10 .

11. If the newspaper is unra v elled or shredded, the blade

did not stop properly , whic h could result in an unsafe

operating condition. Contact an A uthorized Ser vice

Dealer .

Recycling the Clippings

Y our mo w er comes from the factor y ready to recycle the

g rass and leaf clippings bac k into the la wn.

If the g rass bag is on the mo w er , remo v e it (refer to

R emo ving the Grass Bag) before recycling the clippings . If

the side disc harg e c hute is on the mo w er , remo v e it and

loc k the side disc harg e door (refer to R emo ving the Side

Disc harg e Chute) before recycling the clippings .

Bagging the Clippings

Use the g rass bag when y ou w ant to collect g rass and leaf

clippings from the la wn.

A w or n g rass ba g could allo w small stones and

other similar de bris to be thr o wn in the operator’ s or

bystander’ s dir ection and r esult in serious per sonal

injur y or death to the operator or bystander s.

Check the g rass ba g fr equentl y . If it is dama ged,

install a new T or o r eplacement ba g .

If the side disc harg e c hute is on the mo w er , remo v e it and

loc k the side disc harg e door (refer to R emo ving the Side

Disc harg e Chute) before bag ging the clippings .

T he blade is shar p; contacting the blade can r esult

in serious per sonal injur y .

Stop the engine and w ait f or all mo ving par ts to stop

bef or e lea ving the operating position.

Installing the Grass Bag

1. Raise and hold up the rear door ( Figure 26 ).

Figure 26

2. Install the g rass bag ( Figure 27 ).

Figure 27

3. Lo w er the rear door .

Removing the Grass Bag

T o remo v e the bag, rev erse the ste ps abo v e .

Side-discharging the Clippings

Use the side disc harg e for cutting v er y tall g rass .

If the bag is on the mo w er , remo v e it before side-disc harging

the clippings .

T he blade is shar p; contacting the blade can r esult

in serious per sonal injur y .

Stop the engine and w ait f or all mo ving par ts to stop

bef or e lea ving the operating position.

Installing the Side Discharge Chute

1. Unloc k the side disc harg e door ( Figure 28 ).

Figure 28

2. Install the side disc harg e c hute ( Figure 29 ).

Figure 29

Removing the Side Discharge Chute

T o remo v e the side disc harg e c hute , rev erse the ste ps abo v e .

Important: Lock the side discharge door after y ou

close it ( Figur e 30 ).

Figure 30

Operating Tips

General Mowing Tips

• Clear the area of stic ks , stones , wire , branc hes , and

other debris that the blade could hit.

• A v oid striking solid objects with the blade . Nev er

deliberately mo w o v er any object.

• If the mo w er strik es an object or star ts to vibrate ,

immediately stop the engine , disconnect the wire from

the spark plug, and examine the mo w er for damag e .

• F or best perfor mance , install a new blade before the

cutting season begins .

• R e place the blade when necessar y with a T oro

re placement blade .

Cutting Grass

• Cut only about a third of the g rass blade at a time . Do

not cut belo w the 2-inc h (51 mm) setting unless the

g rass is sparse or it is late fall when g rass g ro wth begins

to slo w do wn. R efer to Adjusting the Cutting Height.

• W hen cutting g rass o v er 6 inc hes (15 cm) tall, mo w

at the highest cutting height setting and w alk slo w er;

then mo w ag ain at a lo w er setting for the best la wn

appearance . If the g rass is too long, the mo w er ma y

plug and cause the engine to stall.

• Mo w only dr y g rass or lea v es . W et g rass and lea v es tend

to clump on the yard and can cause the mo w er to plug

or the engine to stall.

W et g rass or lea v es can cause serious injur y if

y ou slip and contact the blade. Mo w onl y in dr y

conditions.

• Be a w are of a potential ﬁre hazard in v er y dr y

conditions , follo w all local ﬁre w ar nings , and k ee p the

mo w er free of dr y g rass and leaf debris .

• Alter nate the mo wing direction. T his helps disperse the

clippings o v er the la wn for ev en fer tilization.

• If the ﬁnished la wn appearance is unsatisfactor y , tr y one

or more of the follo wing:

– R e place the blade or ha v e it shar pened.

– W alk at a slo w er pace while mo wing .

– Raise the cutting height on y our mo w er .

– Cut the g rass more frequently .

– Ov erlap cutting sw aths instead of cutting a full

sw ath with eac h pass .

– Set the cutting height on the front wheels one

notc h lo w er than the rear wheels . F or example , set

the front wheels at 2 inc hes (51 mm) and the rear

wheels at 2-3/8 inc hes (60 mm).

Cutting Leaves

• After cutting the la wn, ensure that half of the la wn

sho ws through the cut leaf co v er . Y ou ma y need to

mak e more than one pass o v er the lea v es .

• If there are more than 5 inc hes (13 cm) of lea v es on the

la wn, set the front cutting height one or tw o notc hes

higher than the rear cutting height.

• Slo w do wn y our mo wing speed if the mo w er does not

cut the lea v es ﬁnely enough.

Maintenance

Note: Deter mine the left and right sides of the mac hine from the nor mal operating position.

Recommended Maintenance Schedule(s)

Maintenance Service

Interval

Maintenance Procedure

After the rst 2 operating

hours

• Change the engine oil.

Before each use or daily

• Check the engine oil level.

• Ensure that the engine stops within 3 seconds after releasing the blade control

bar.

• Check the blade brake clutch operation.

• Clean grass clippings and dirt from under the mower.

Every 25 hours

• Charge the battery for 24 hours (models 20076 and 20076A only).

Before storage

• Empty the fuel tank before repairs as directed and before annual storage.

Yearly

• Replace the air lter (more frequently in dusty operating conditions).

• Change the engine oil.

• Lubricate the wheel gears.

• Replace the blade or have it sharpened (more frequently if the edge dulls quickly).

• Refer to your Engine Operator’s Manual for any additional yearly maintenance

procedures.

Important: R efer to y our Engine Operator’ s Man ual f or additional maintenance pr ocedur es.

Preparing for Maintenance

1. Stop the engine and w ait for all mo ving par ts to stop .

2. Disconnect the spark plug wire from the spark plug

and hook it onto the retaining post ( Figure 31 ) before

perfor ming any maintenance procedure .

Figure 31

1. Spark plug retaining post

3. After perfor ming the maintenance procedure(s),

connect the spark plug wire to the spark plug .

Important: Bef or e tipping the mo w er to change

the oil or r eplace the blade, allo w the fuel tank to

r un dr y thr ough nor mal usa ge. If y ou must tip the

mo w er prior to r unning out of fuel, use a hand fuel

pump to r emo v e the fuel. Al w ays tip the mo w er

onto its side, with the air ﬁlter up .

Tipping the mo w er may cause the fuel to leak.

Gasoline is ﬂamma ble, explosi v e and can cause

per sonal injur y .

R un the engine dr y or r emo v e the gasoline with a

hand pump; nev er siphon.

Replacing the Air Filter

R e place the air ﬁlter yearly; re place it more frequently in

dusty operating conditions .

1. R efer to Pre paring for Maintenance .

2. R otate the air ﬁlter co v er to remo v e it ( Figure 32 ).

Figure 32

1. Air lter cover 2. Air lter

3. R e place the air ﬁlter .

4. Install the co v er .

Changing the Engine Oil

Change the engine oil after the ﬁr st 2 operating hour s ;

c hang e it yearly thereafter .

R un the engine a few min utes before c hanging the oil

to w ar m it. W ar m oil ﬂo ws better and car ries more

contaminants .

1. R efer to Pre paring for Maintenance .

2. R emo v e the dipstic k ( Figure 33 ).

Figure 33

3. Tip the mo w er onto its side with the air ﬁlter up to drain

the used oil out through the oil ﬁll tube ( Figure 34 ).

Figure 34

4. Slo wl y pour oil into the oil ﬁll tube until the oil lev el

reac hes the Full line on the dipstic k ( Figure 35 ). Do not

o v erﬁll. (Max. ﬁll: 20 oz., type: SAE 30W deterg ent

oil with an API ser vice classiﬁcation of SF , SG , SH, SJ ,

SL, or higher .)

Figure 35

5. Install the dipstic k securely .

6. Dispose of the used oil properly at a local recycling

center .

Charging the Battery

Models 20076 and 20076A onl y

Warning

CALIFORNIA

Pr oposition 65 W ar ning

Batter y posts, ter minals, and r elated accessories

contain lead and lead compounds, chemicals kno wn

to the State of Calif or nia to cause cancer and

r epr oducti v e har m. W ash hands after handling .

Charg e the batter y for 24 hours initially , then monthly

(ev er y 25 star ts) or as needed. Alw a ys use the c harg er in a

sheltered area and c harg e the batter y at room temperature

(70° or 22° C) whenev er possible .

1. Connect the c harg er to the mo w er wire har ness located

belo w the ignition k ey ( Figure 36 ).

Figure 36

2. Plug the c harg er into a w all outlet.

Note: W hen the batter y no long er holds a c harg e ,

recycle or dispose of the lead-acid batter y according to

local codes .

Replacing the Fuse

Models 20076 and 20076A onl y

If the batter y does not c harg e or the engine does not r un

with the electric star ter , the fuse ma y be blo wn. R e place it

with a 40-amp plug-in type fuse . R efer to Installing the Fuse .

Lubricating the Wheel Gears

1. R emo v e the wheel bolts on the r ear wheels and remo v e

the rear wheels .

2. Apply a lubricating oil to the inner and outer sides of

the g ear as sho wn in Figure 37 .

Figure 37

3. Install the rear wheels .

Replacing the Blade

Important: Y ou will need a torque wr ench to install

the blade pr oper l y . If y ou do not ha v e a torque wr ench

or ar e uncomf or ta ble perf or ming this pr ocedur e,

contact an Authoriz ed Ser vice Dealer .

Examine the blade whenev er y ou r un out of g asoline . If the

blade is damag ed or crac k ed, re place it immediately . If the

blade edg e is dull or nic k ed, ha v e it shar pened or re place it.

T he blade is shar p; contacting the blade can r esult

in serious per sonal injur y .

W ear g lo v es when ser vicing the blade.

1. Disconnect the spark plug wire from the spark plug .

R efer to Pre paring for Maintenance .

2. Tip the mo w er onto its side with the air ﬁlter up .

3. R emo v e the 2 blade n uts and the stiffener ( Figure 38 ).

Figure 38

1. Blade nuts 2. Stiffener

4. R emo v e the blade ( Figure 38 ).

5. Install the new blade ( Figure 38 ).

6. Install the stiffener y ou previously remo v ed.

7. Install the blade n uts and torque them to 15 to 27

ft-lb (20 to 37 N ⋅ m).

Cleaning the Blade Brake

Clutch Shield

Clean the blade brak e clutc h shield yearly to prev ent the

blade from stalling while y ou mo w .

1. Disconnect the spark plug wire from the spark plug .

R efer to Pre paring for Maintenance on pag e 18.

2. Tip the mo w er onto its side with the air ﬁlter up .

3. R emo v e the 2 blade n uts and the stiffener ( Figure 39 ).

Figure 39

1. Blade nuts 4. Blade driver

2. Stiffener 5. Disk

3. Blade 6. Blade brake clutch shield

4. R emo v e the blade ( Figure 39 ).

5. R emo v e the blade dri v er and disk ( Figure 39 ).

6. R emo v e the blade brak e clutc h shield ( Figure 39 ).

7. Br ush or blo w out debris from the inside of the shield

and around all the par ts .

8. Install the blade brak e clutc h shield that y ou previously

remo v ed.

9. Install the blade dri v er that y ou previously remo v ed.

10. Install the blade and the stiffener that y ou previously

remo v ed ( Figure 39 ).

11. Install the blade n uts and torque them to 15 to 27

ft-lb (20 to 37 N ⋅ m).

Page is loading ...

Toro 22in Recycler Lawn Mower User manual

Brand: Toro

Model: 22in Recycler Lawn Mower

Category: Lawnmowers

Type: User manual

Download PDF

report

Toro 22in Recycler Lawn Mower User manual

Toro 22in Recycler Lawn Mower User manual

Related papers

Other documents