Golden Lighting 1025-BA2 CH Installation guide

Type
Installation guide

This manual is also suitable for

IMPORTANT:
• ALLINSTALLATIONWORKSHOULDBEDONEBYACCREDITEDPROFESSIONAL.
• SHUTOFFPOWERSUPPLYATFUSEORCIRCUITBREAKER!
• USEONLYTHESPECIFIEDBULBS.DONOTEXCEEDTHEMAXIMUMWATTAGE!
For Customer Service, contact
the place of purchase.
AssemblyInstructions:1025-BA2, BA3, BA4 (Krysta)
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
F
E
A
G
B
D
I
J
C
H
FINISHING THE INSTALLATION
3.Placethexture’sbackplate(F)overmountingstrap(B)sothatthekeyholesinthetopofmountingstrap(A)lineupwiththeholesin
backplate(B).Threadscrews(F)intotheholes.
4.Installlightbulb(J-provided)inaccordancewiththexture’sspecications.Donotexceedthemaximumrecommendedwattage.
BulbNote:Useatissueorpapertoweltoholdthebulbandpushdownintothesocket.Oilsanddirtcancausethebulblifetoshorten.
Rubbingalcoholisrecommendedtocleanthebulbswhenneeded.
5.Crystals(I)areinstalled,butifonecomesoff,pleaserefertothediagramaboveofthecrystalinstallation.
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
PREPARING FOR INSTALLATION
Removeallofthecontentsfromthecarton.Seetheimportantnotesabove.Removetheoldxturefromthewall,includingtheold
mountingstrap.
1.Takethemountingstrapassemblyfromthepartsbag.Mountingstrap(B)containsthreadedholes.Lineuptheholesin
backplate(F)withtheholesinmountingstrap(B)andsecuremountingstrap(B)tothejunctionboxwithmountingscrews(D)anda
screwdriver.Tightenthescrewssecurely.
CONNECTING THE WIRES
2.Haveanassistantsupportthexture’sweightwhilecompletingthewiring.Refertothewiringdiagrambelowandattachthexture’s
wirestothepowersupplywiresfromthejunctionbox.ConnectHottoHot,NeutraltoNeutral,andGroundtoGround.Twisttheends
ofthewirepairstogether,andthentwistonawireconnector.Makesurealltwistsareinthesamedirection.Ifthereisnohouseground
wirecomingfromthejunctionbox,locategroundscrew(E)onthemountingbracket/mountingstrapandwrapthexture’sground
wirearoundthegroundscrew.Useascrewdrivertotightenthetopofgroundscrew(E)ontothewiresandintothemountingbracket/
mountingstrap.Tuckthewiresintothejunctionbox.
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
1025-BA4
1025-BA2
1025-BA3
  • Page 1 1

Golden Lighting 1025-BA2 CH Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI