Fujitsu ASYG07LMCE-R Installation guide

Brand: Fujitsu

Model: ASYG07LMCE-R

Category: Split-system air conditioners

Type: Installation guide

This manual is also suitable for

En-1

1. SAFETY PRECAUTIONS

• BesuretoreadthisManualthoroughlybeforeinstallation.

• ThewarningsandprecautionsindicatedinthisManualcontainimportantinformation

pertainingtoyoursafety.Besuretoobservethem.

• HandthisManual,togetherwiththeOperatingManual,tothecustomer.Requestthe

customertokeepthemonhandforfutureuse,suchasforrelocatingorrepairingtheunit.



WARNING

Indicatesapotentiallyorimminentlyhazardoussituation

which,ifnotavoided,couldresultindeathorseriousinjury.

•Installationofthisproductmustbedonebyexperiencedservicetechniciansorprofes-

sionalinstallersonlyinaccordancewiththismanual.Installationbynon-professionalor

improperinstallationoftheproductmightcauseseriousaccidentssuchasinjury,water

leakage,electricshock,orre.Iftheproductisinstalledindisregardoftheinstructions

inthismanual,itwillvoidthemanufacturer’swarranty.

•Donotturnonthepoweruntilallworkhasbeencompleted.Turningonthepowerbe-

foretheworkiscompletedcancauseseriousaccidentssuchaselectricshockorre.

•Ifrefrigerantleakswhenyouareworking,ventilatethearea.Iftheleakingrefrigerantis

exposedtoadirectame,itmayproduceatoxicgas.

•Installationmustbeperformedinaccordancewithregulations,codes,orstandardsfor

electricalwiringandequipmentineachcountry,region,ortheinstallationplace.

CAUTION

Indicatesapotentiallyhazardoussituationthatmayresultin

minorormoderateinjuryordamagetoproperty.

•Readcarefullyallsafetyinformationwritteninthismanualbeforeyouinstallorusethe

airconditioner.

•Installtheproductbyfollowinglocalcodesandregulationsinforceattheplaceof

installation,andtheinstructionsprovidedbythemanufacturer.

•Thisunitmustbeinstalledbyqualiedpersonnelwithacapacitycerticateforhandling

refrigerantuids.Refertoregulationandlawsinuseoninstallationplace.

•Thisproductispartofasetconstitutinganairconditioner.Theproductmustnotbe

installedaloneorbeinstalledwithadevicenotauthorizedbythemanufacturer.

•Alwaysuseaseparatepowersupplylineprotectedbyacircuitbreakeroperatingonall

wireswithadistancebetweencontactof3mmforthisproduct.

•Toprotectthepersons,earth(ground)theproductcorrectly,andusethepowercable

combinedwithanEarthLeakageCircuitBreaker(ELCB).

•Thisproductisnotexplosionproof,andthereforeshouldnotbeinstalledinanexplo-

siveatmosphere.

•Toavoidgettinganelectricshock,nevertouchtheelectricalcomponentssoonafterthe

powersupplyhasbeenturnedoff.Afterturningoffthepower,alwayswait5minutesor

morebeforeyoutouchtheelectricalcomponents.

•Thisproductcontainsnouser-serviceableparts.Alwaysconsultexperiencedservice

techniciansforrepairing.

•Whenmovingorrelocatingtheairconditioner,consultexperiencedservicetechnicians

fordisconnectionandreinstallationoftheproduct.

•Donottouchthealuminumnsofheatexchangerbuilt-intheindoororoutdoorunitto

avoidpersonalinjurywhenyouinstallormaintaintheunit.

•Donotplaceanyotherelectricalproductsorhouseholdbelongingsundertheproduct.

Condensationdrippingfromtheproductmightgetthemwet,andmaycausedamage

ormalfunctiontotheproperty.

2. ABOUT THE PRODUCT

2.1. Precautions for using R410A refrigerant

Thebasicinstallationworkproceduresarethesameasconventionalrefrigerant(R22)

models.

However,paycarefulattentiontothefollowingpoints:

Sincetheworkingpressureis1.6timeshigherthanthatofconventionalrefrigerant

(R22)models,someofthepipingandinstallationandservicetoolsarespecial.(See

thetablebelow.)

Especially,whenreplacingaconventionalrefrigerant(R22)modelwithanewrefrigerant

R410Amodel,alwaysreplacetheconventionalpipingandflarenutswiththeR410Apiping

andarenuts.

ModelsthatuserefrigerantR410Ahaveadifferentchargingportthreaddiametertopre-

venterroneouschargingwithconventionalrefrigerant(R22)andforsafety.Therefore,

checkbeforehand.[ThechargingportthreaddiameterforR410Ais1/2-20UNF.]

Bemorecarefulthatforeignmatter(oil,water,etc.)doesnotenterthepipingthanwith

refrigerant(R22)models.Also,whenstoringthepiping,securelysealtheopeningby

pinching,taping,etc.

Whenchargingtherefrigerant,takeintoaccounttheslightchangeinthecompositionof

thegasandliquidphases.Andalwayschargefromtheliquidphasewhererefrigerant

compositionisstable.

2.2. Special tools for R410A

Tool name Contents of change

Gauge manifold

Pressureishighandcannotbemeasuredwith a conven-

tional(R22)gauge.Topreventerroneousmixing of other

refrigerants,thediameterofeachporthasbeenchanged.

Itisrecommended thegaugewith seals -0.1to5.3 MPa

(-1to53bar)forhighpressure.

-0.1to3.8MPa(-1to38bar)forlowpressure.

Charge hose

Toincreasepressureresistance,thehosematerialandbase

sizewerechanged.

Vacuum pump

A conventionalvacuumpumpcanbeusedbyinstallinga

vacuumpumpadapter.

Gas leakage detector SpecialgasleakagedetectorforHFCrefrigerantR410A.

Copper pipes

Itisnecessarytouseseamlesscopperpipesanditisdesirablethattheamountofresidual

oilisless than 40mg/10m.Do notusecopperpipeshaving a collapsed,deformedor

discoloredportion(especially on the interior surface). Otherwise, the expansion valueor

capillarytubemaybecomeblockedwithcontaminants.

AsanairconditionerusingR410AincurspressurehigherthanwhenusingR22,itisneces-

sarytochooseadequatematerials.

WARNING

Do not use the existing (for R22) piping and are nuts.

Iftheexistingmaterialsareused,thepressureinsidetherefrigerantcyclewillriseand

causefailure,injury,etc.(UsethespecialR410Amaterials.)

When installing and relocating the air conditioner, do not mix gases other than

the specied refrigerant (R410A) to enter the refrigerant cycle.

Ifairorothergasenterstherefrigerantcycle,thepressureinsidethecyclewillriseto

anabnormallyhighvalueandcausefailure,injury,etc.

AIRCONDITIONER

WallMountedType

INSTALLATION MANUAL

Contents

1. SAFETYPRECAUTIONS.................................................................. 1

2. ABOUTTHEPRODUCT.................................................................... 1

3. GENERALSPECIFICATION............................................................. 2

4. ELECTRICALREQUIREMENT......................................................... 2

5. SELECTINGTHEMOUNTINGPOSITION....................................... 2

6. INSTALLATIONWORK..................................................................... 3

7. ELECTRICALWIRING...................................................................... 5

8. FINISHING......................................................................................... 5

9. FRONTPANELREMOVALANDINSTALLATION............................. 6

10. REMOTECONTROLLERINSTALLATION........................................ 6

11. OPTIONALKITINSTALLATION........................................................ 6

12. FUNCTIONSETTING........................................................................ 9

13. TESTRUN....................................................................................... 10

14. CUSTOMERGUIDANCE................................................................ 10

15. ERRORCODES...............................................................................11

PARTNo.9333005225

EnglishРусский

[Originalinstructions] Forauthorizedservicepersonnelonly.

9333005225_IM_2L.indb 1 10/12/2017 08:48:28

En-2

2.3. For authorized service personnel only

WARNING

•Fortheairconditionertooperatesatisfactorily,installitasoutlinedinthisinstallation

manual.

•Connecttheindoorunitandoutdoorunitwiththeairconditionerpipingandcables

availablefromyourlocaldistributor.Thisinstallationmanualdescribesthecorrect

connectionsusingtheinstallationsetavailablefromyourlocaldistributor.

•Installationworkmustbeperformedinaccordancewithnationalwiringstandardsby

authorizedpersonnelonly.

•Donotturnonthepoweruntilallinstallationworkiscomplete.

CAUTION

Thisinstallationmanualdescribeshowtoinstalltheindoorunitonly.

Toinstalltheoutdoorunit,refertotheinstallationmanualincludedwiththeoutdoorunit.

• Becarefulnottoscratchtheairconditionerwhenhandlingit.

2.4. Accessories

Thefollowinginstallationaccessoriesaresupplied.Usethemasrequired.

Name and Shape

Q’ty

Name and Shape

Q’ty

OperatingManual

Clothtape

InstallationManual

(Thismanual)

SealA

Itisusedwhenthediameterof

gaspipeisØ12.70ormore.

ItisnecessarywhenusingAS14.

Wallhookbracket

Tappingscrews

(large)

Remotecontroller

Tappingscrews

(small)

Battery

Aircleaningfilter

Remotecontrollerholder

Filterholders

Thefollowingitemsarenecessarytoinstallthisairconditioner.(Theitemsarenotinclud-

edwiththeairconditionerandmustbepurchasedseparately.)

Name Q’ty Name Q’ty

Connectionpipeassembly 1 Wallcap 1

Connectioncable(4-conductor)

1 Saddle 1set

Wallpipe 1 Drainhose 1

Decorativetape 1 Tappingscrews 1set

Vinyltape 1 Sealant 1

2.5. Optional parts

Refertoeachinstallationmanualforthemethodofinstallingoptionalparts.

Parts name Model No. Application

WiredRemoteController* UTY-RVNÜM Forairconditioneroperation

WiredRemoteController* UTY-RNNÜM Forairconditioneroperation

SimpleRemoteController* UTY-RSNÜM Forairconditioneroperation

Externalconnectkit* UTY-XWZXZ5 Forcontrolinput/outputport

Communicationkit UTY-XCBXZ2 Fortheinstallationofoptionalparts

*Optionalcommunicationkitisnecessaryfortheinstallation.

3. GENERAL SPECIFICATION

ThisINSTALLATIONMANUALbrieyoutlineswhereandhowtoinstalltheairconditioningsystem.

Pleasereadovertheentire setofinstructionsfortheindoorand outdoor unitsandmakesureall

accessorypartslistedarewiththesystembeforebeginning.

3.1. Type of copper pipe and insulation material

CAUTION

Refertotheinstallationmanualfortheoutdoorunitfordescriptionofallowablepipelength

andheightdifference.

Model

Gas pipe size (thickness)

[mm]

Liquid pipe size (thickness)

[mm]

7,9,12

9.52(0.8)

Ø

6.35(0.8)

Ø

12.70(0.8)

Ø

6.35(0.8)

CAUTION

•Installheatinsulationaroundboththegasandliquidpipes.Failuretodosomay

causewaterleaks.

•

Useheatinsulationwithheatresistanceabove120°C.Reversecyclemodelonly)

•Inaddition,ifthehumiditylevelattheinstallationlocationoftherefrigerantpipingis

expectedtoexceed70%,installheatinsulationaroundtherefrigerantpiping.Ifthe

expectedhumiditylevelis70-80%,useheatinsulationthatis15mmorthickerandif

theexpectedhumidityexceeds80%,useheatinsulationthatis20mmorthicker.

•

fheatinsulationisusedthatisnotasthickasspecied,condensationmayformon

thesu

rfaceoftheinsulation.

•Inaddition,useheatinsulationwithheatconductivityof0.045W/(m•K)orless20°C.

3.2. Additional materials required for installation

A.Refrigeration(armored)tape

B.Insulatedstaplesorclampsforconnectingwire(Seeyourlocalelectricalcodes.)

C.Putty

D.Refrigerationlubricant

E.Clampsorsaddlestosecurerefrigerantpiping

4. ELECTRICAL REQUIREMENT

Theindoorunitispoweredfromtheoutdoorunit.Donotpowerindoorunitfromseparate

powersource.

WARNING

Refertolocalcodesforacceptablecabletype.

Cable

Cable size

Remarks

Connectioncable

Type60245IEC57

(1.5mm

)

3cable+Ground,1.5Ø230V

CableLength:Limitvoltagedroptolessthan2%.Increasecablegaugeifvoltagedropis

2%ormore.

5. SELECTING THE MOUNTING POSITION

Decidethemountingpositionwiththecustomerasfollows:

5.1. Indoor unit

(1) Installtheindoorunitlevelonastrongwallwhichisnotsubjecttovibration.

(2) Theinletandoutletportsshouldnotbeobstructed:theairshouldbeabletoblowall

overtheroom.

(3)

Installtheunitadedicatedelectricalbranchcircuit.

(4)

Donotinstalltheunitwhereitwillbeexposedtodirectsunlight.

(5)

Installtheunitwhereconnectiontotheoutdoorunitiseasy.

(6) Installtheunitwherethedrainpipecanbeeasilyinstalled.

(7) Takeservicing,etc.intoconsiderationandleavethespacesshownin[6.1.Installation

dimensions].Alsoinstalltheunitwheretheltercanberemoved.

Correctinitialinstallationlocationisimportantbecauseitisdifculttomoveunitafteritis

installed.

WARNING

Selectinstallationlocationsthatcanproperlysupporttheweightoftheindoorunit.

Installtheunitssecurelysothattheydonottoppleorfall.

CAUTION

Donotinstalltheunitinthefollowingareas:

•Areawithhighsaltcontent,suchasattheseaside.Itwilldeterioratemetalparts,caus-

ingthepartstofailortheunittoleakwater.

•Arealledwithmineraloilorcontainingalargeamountofsplashedoilorsteam,such

asakitchen.

Itwilldeteriorateplasticparts,causingthepartstofailortheunittoleakwater.

•Areathatgeneratessubstancesthatadverselyaffecttheequipment,suchassulfuric

gas,chlorinegas,acid,oralkali.

Itwillcausethecopperpipesandbrazedjointstocorrode,whichcancauserefrigerant

leakage.

•Areathatcancausecombustiblegastoleak,containssuspendedcarbonbersor

ammabledust,orvolatileinammablessuchaspaintthinnerorgasoline.

•Ifgasleaksandsettlesaroundtheunit,itcancauseare.

•Areawhereanimalsmayurinateontheunitorammoniamaybegenerated.

•Donotusetheunitforspecialpurposes,suchasstoringfood,raisinganimals,grow-

ingplants,orpreservingprecisiondevicesorartobjects.

•Itcandegradethequalityofthepreservedorstoredobjects.

•Donotinstallwherethereisthedangerofcombustiblegasleakage.

9333005225_IM_2L.indb 2 10/12/2017 08:48:34

En-3

•Donotinstalltheunitnearasourceofheat,steam,orammablegas.

•Installtheunitwheredrainagedoesnotcauseanytrouble.

•Installtheindoorunit,outdoorunit,powersupplycable,connectioncable,andremote

controlcableatleast1mawayfromatelevisionorradioreceivers.Thepurposeof

thisistopreventTVreceptioninterferenceorradionoise.

•(Eveniftheyareinstalledmorethan1mapart,youcouldstillreceivenoiseunder

somesignalconditions.)

•Ifchildrenunder10yearsoldmayapproachtheunit,takepreventivemeasuresso

thattheycannotreachtheunit.

•Installtheindoorunitonthewallwheretheheightfromtheoorsmorethan1800mm.

6. INSTALLATION WORK

6.1. Installation dimensions

Outlineoftheindoorunit

Unit:mm

Wallhookbracket

144or

1,500

ormore

1,800ormore

(52or

more)

(25or

more)

86or

63or

(45or

more)

6.2. Indoor unit piping direction

Thepipingcanbeconnectedinthe

directionsindicatedinthefollowing.

Whenthepipingisconnectedindirection

,

or

,

cutalongthepipinggroovein

thesideofthefrontcoverwithahacksaw.

Right

outlet

Left

outlet

Leftrear

outlet

Bottomoutlet

Rearoutlet

Leftbottomoutlet

(Rear)

6.3.

Cutting the hole in the wall for the connecting piping

(1) Cuta65mmdiameterholeinthewallatthepositionshowninthefollowing.

(2) Cuttheholesothattheoutsideendislower(5to10mm)thantheinsideend.

(3) Alwaysalignthecenterofthewallhole.Ifmisaligned,waterleakagewilloccur.

(4)

Cutthewallpipetomatchthewallthickness,stickitintothewallcap,fastenthecapwith

vinyltape,andstickthepipethroughthehole.

(5) Forleftpipingandrightpiping,cuttheholealittlelowersothatdrainwaterwillow

freely.

Wall

Fastenwith

vinyltape*

65mmdia.hole

Wallhookbracket

Centermark

Wallcap*

Wallpipe*

(Inside)

(Outside)

5to10mmlow

*Locallypurchased

WARNING

Ifthewallpipeisnotused,thecableinterconnectingtheindoorunit(s)andoutdoorunit

maytouchmetalandcauseelectricdischarge.

6.4. Installing the wall hook bracket

•Removethewallhookbracketfromtheindoorunit.(Remove2screws).

(1)Installthewallhookbracketsothatitiscorrectlypositionedhorizontallyandvertically.

Ifthewallhookbracketistitled,waterwilldriptotheoor.

(2)

Installthewallhookbracketsothatitisstrongenoughtosupporttheweightoftheunit.

•Fasten thewallhook brackettothe wallwith5 or morescrewsthrough theholes

neartheouteredgeofthebracket.

•Checkthatthereisnorattleatthewallhookbracket.

Wallhookbracket

Tappingscrews(large,accessories)

CAUTION

Installthewallhookbracketbothhorizontallyandverticallyaligned.Misalignedinstalla-

tionmaycausewaterleakage.

6.5. Forming the drain hose and pipe

[Rear piping, Right piping, Bottom piping]

•Installtheindoorunitpipinginthedirectionofthewallholeandbind thedrainhose

andpipetogetherwithvinyltape.

•Installthepipingsothatthedrainhoseisatthebottom.

•Wrapthepipesoftheindoorunitthatarevisiblefromtheoutsidewithdecorativetape.

[For Left rear piping, Left piping]

Interchangethedraincapandthedrainhose.

CAUTION

•



Insertdrainhoseanddraincapsecurely.Drainshouldslopedowntoavoidwaterleakage.

•When inserting,besurenottoattachanymaterialbesideswater.Ifanyother

materialisattached,itwillcausedeteriorationandwaterleakage.

•Afterremovingdrainhose,besurenottoforgetmountingdraincap.

•Besuretoxthedrainhosewithtapetothebottomofpiping.

•Preventdrainwaterfreezingunderlowtemperatureenvironment.

Wheninstallingindoorunit’sdrainhoseoutdoors,necessarymeasureforfrost

protectionshouldbetakentopreventdrainwaterfreezing.

Underlowtemperatureenvironment(whenoutdoortemperatureunder0°C),after

coolingoperationisexecuted,waterinthedrainhosecouldbefrozen.Oncedrainwater

isfrozen,thedrainhosewillbeblockedandwaterleakagemayresultattheindoorunit.

Installation method of Drain cap

Useahexagonalwrench4mmatoppositesidetoinsert

thedraincap,tillthedraincapcontactsthetipofdrain

cock.

Rightpiping

Bottompiping

Bindwithvinyltape

Refrigerantpipes(top)

Rearpiping

Indoorunitdrainhose(bottom)

Forleftoutletpiping,

cutoffthepiping

outletcuttinggroove

withahacksaw.

Indoorunit

drainhose

Draincap

Removethedraincapbypull-

ingattheprojectionattheend

ofthecapwithpliers,etc.

Nogap

Hexagonal

wrench

Drain



cock

Draincap

9333005225_IM_2L.indb 3 10/12/2017 08:48:41

En-4

Removal method of drain hose

Removethescrewattheleftofdrain

hoseandpulloutdrainhose.

Installation method of drain hose

Verticallyinsertthedrainhosetowardthe

inside,sothatthedrainxture(white)canac

curatelyalign with the screw hole around the

draincock.

Afterinserting and before replacing,please

reinstallandxtheremovedscrews.

• Pleaseholdaroundthejointofthedrainhoseduringworking.

•

Asthescrewisinside,besuretousescrewdrivertreatedwithmagnet.

Screw

Drainfixture

Drainhose

Screwhole

Draincock

Drainhose

Screw

Drainfixture

•

Forleftpipingandleftrearpiping,alignthemarksonthewallhookbracketandshapethe

connectionpipe.

•Bendtheconnectionpipingatabendradiusof70mmormoreandinstallnomorethan

35mmfromthewall.

•

Afterpassingtheindoorpipinganddrainhosethroughthewallhole,hangtheindooruniton

thehooksatthetopandbottomofthewallhookbracket.

[Installing the indoor unit]

• Hangtheindoorunitfromthehooksatthetopofthewallhookbracket.

• Insertthespacer,etc.betweentheindoorunitandthewallhookbracketandseparate

thebottomoftheindoorunitfromthewall.

Indoorunit

Wallhookbracket

(Spacer)

Connectionpipe(6.35mmdia.)

Alignthemarks

Indoorunit

Connectionpipe(9.52or12.7mmdia.)

Tophooks

Bottomhooks

Wallhookbracket

BendR70mmwith

apipebender

Afterhookingtheindoorunittothetophook,hookthettingsoftheindoorunittothe2

bottomhookswhileloweringtheunitandpushingitagainstthewall.

6.6. Flare connection (Pipe connection)

CAUTION

Tightenthearenutswithatorquewrenchusingthespeciedtighteningmethod.Oth-

erwise,thearenutscouldbreakafteraprolongedperiod,causingrefrigeranttoleak

andgeneratehazardousgasiftherefrigerantcomesintocontactwithaame.

6.6.1. Flaring

UsespecialpipecutterandaretoolexclusiveforR410A.

(1) Cuttheconnectionpipetothenecessarylengthwithapipecutter.

(2) Holdthepipedownwardsothatcuttingswillnotenterthepipeandremoveanyburrs.

(3)

Inserttheare nut (always use the are nutattachedtothe indoor unit(s) and outdoor

unitrespectively)ontothepipeandperformtheareprocessingwithaaretool.Usethe

specialR410Aaretool,ortheconventionalaretool.Leakageofrefrigerantmayresultif

otherarenutsareused.

(4) Protectthepipes bypinchingthem orwithtape topreventdust, dirt, orwaterfrom

enteringthepipes.

Die

Pipe

Checkif[L]isflareduniformly

andisnotcrackedorscratched.

Pipe outside diameter

[mm (in.)]

Dimension A [mm]

Dimension B

[mm]

Flare tool for R410A, clutch type

6.35(1/4)

0to0.5

9.1

9.52(3/8) 13.2

12.70(1/2) 16.6

15.88(5/8) 19.7

19.05(3/4) 24.0

WhenusingconventionalaretoolstoareR410Apipes,thedimensionAshouldbeap-

proximately0.5mmmorethanindicatedinthetable(foraringwithR410Aaretools)to

achievethespeciedaring.UseathicknessgaugetomeasurethedimensionA.

Widthacross

flats

Pipe outside diameter

[mm (in.)]

Width across flats of Flare

nut [mm]

6.35(1/4) 17

9.52(3/8) 22

12.70(1/2) 26

15.88(5/8) 29

19.05(3/4) 36

6.6.2. Bending pipes

• Ifpipesareshapedbyhand,becarefulnottocollapsethem.

• Donotbendthepipesinananglemorethan90°.

• Whenpipesarerepeatedlybendorstretched,thematerialwillharden,makingitdifcult

tobendorstretchthemanymore.

• Donotbendorstretchthepipesmorethan3times.

CAUTION

•Topreventbreakingofthepipe,avoidsharpbends.

•Ifthepipeisbentrepeatedlyatthesameplace,itwillbreak.

6.6.3. Pipe connection

CAUTION

•Besuretoinstallthepipeagainsttheportontheindoorunitcorrectly.Ifthecenter-

ingis improper,the are nut cannot tighten smoothly. If theare nut is forcedto

turn,thethreadswillbedamaged.

•Donotremovethearenutfromtheindoorunitpipeuntilimmediatelybeforecon-

nectingtheconnectionpipe.

•Holdthetorquewrenchatitsgrip,keepingitintherightanglewiththepipe,inorder

totightenthearenutcorrectly.

•Tightenthe are nuts with a torque wrench using the specied tightening method.

Otherwise,thearenutscouldbreakafteraprolongedperiod,causingrefrigerantto

leakandgeneratehazardousgasiftherefrigerantcomesintocontactwithaame.

CAUTION

•Connectthepipingsothatthecontrolboxcovercaneasilyberemovedforservic-

ingwhennecessary.

•Inordertopreventwaterfromleakingintothecontrolbox,makesurethatthepip-

ingiswellinsulated.

Whentheflarenutistightenedproperlybyyourhand,holdthebodysidecouplingwitha

wrench,thentightenwithatorquewrench.(Seethetablebelowfortheflarenuttightening

torques.)



Tightenwithtwowrenches.

Holdingwrench

Flarenut

Connectionpipe

Torquewrench

Indoorunitpipe

(Bodyside)

Flarenut[mm(in.)] Tighteningtorque[N·m(kgf·cm)]

6.35(1/4)dia. 16to18(160to180)

9.52(3/8)dia. 32to42(320to420)

12.70(1/2)dia. 49to61(490to610)

15.88(5/8)dia. 63to75(630to750)

19.05(3/4)dia. 90to110(900to1,100)

9333005225_IM_2L.indb 4 10/12/2017 08:48:43

En-5

7. ELECTRICAL WIRING

7.1. Wiring system diagram

WARNING

•Everywiremustbeconnectedrmly.

•Nowireshouldbeallowedtotouchrefrigeranttubing,thecompressororanymov-

ingpart.

•Loosewiringmaycausetheterminaltooverheatorresultinunitmalfunction.Are

hazardmayalsoexist.Therefore,besureallwiringistightlyconnected.

•Connectwirestothematchingnumbersofterminals.

Groundingline

Type60245IEC57

(Inter-unit)

OUTDOORUNIT

Pleaseconnectitto

thespeciedterminal.

INDOORUNIT

TERMINAL

Powerline

Controlline

7.2. Indoor unit wiring

1.Removethewirecover.(Remove1screw.)

2.Removethecableclamp.

3.Ringterminalsconnecttotheconnectioncable.

4.Connecttheringterminalsfullyintotheterminalblock.

5.Fastentheconnectioncablewithacableclamp.

Wirecover

Screw

Insertthewirecovertabintothesquarehole

oftheindoorunitandfastenwithascrew.

Connectioncable

60mm

40mm

Cableclamp

Earth(Ground)wire

7.3. How to connect wiring to the terminals

Cautionwhenwiringcable

Whenstrippingofftheinsulationofaleadwire,alwaysuseaspecialtoolsuchasawire

stripper.Ifthereisnospecialtoolavailable,carefullystriptheinsulationwithaknifeetc.

(1) Usering terminalswith insulatingsleevesasshowninthegureto connect to the

terminalblock.

(2) Securelyclamptheringterminalstothewiresbyusinganappropriatetoolsothatthe

wiresdonotcomeloose.

Strip:10mm

Ringterminal

Sleeve

(3) Usethespeciedwires,connectthemsecurely,andfastenthemsothatthereisno

stressplacedontheterminals.

(4) Useanappropriatescrewdrivertotightentheterminalscrews.Donotuseascrew-

driverthatistoosmall,otherwise,thescrewheadsmaybedamagedandpreventthe

screwsfrombeingproperlytightened.

(5) Donottightentheterminalscrewstoomuch,otherwise,thescrewsmaybreak.

Screwwithspecialwasher

Wire

Ringterminal

Terminalblocks

Wire

Screwwithspecialwasher

Ringterminal

(6) Seethefollowingtablefortheterminalscrewtighteningtorques.

Tighteningtorque[N·m(kgf·cm)]

M4screw 1.2to1.8(12to18)

CAUTION

•Matchtheterminalblocknumbersandconnectioncablecolorswiththoseofthe

outdoorunit.

Erroneouswiringmaycauseburningoftheelectricparts.

•Connecttheconnectioncablesrmlytotheterminalblock.Imperfectinstallationmay

causeare.

•Alwaysfastentheoutsidecoveringoftheconnectioncablewiththecableclamp.(If

theinsulatorischafed,electricdischargemayoccur.)

•Alwaysconnectthegroundwire.

•Donotusetheearthscrewoftheindoorunitfortheconnectionotherthanaspecied

outdoorunit.

8. FINISHING

(1) Insulatebetweenpipes.

• Insulatesuctionanddischargepipesseparately.

• Forrear,right,andbottompiping,overlaptheconnectionpipeheatinsulationand

indoorunitpipeheatinsulationandbindthemwithvinyltapesothatthereisnogap.

• Forleftandleftrearpiping,butttheconnectionpipeheatinsulationandindoorunit

pipeheatinsulationtogetherandbindthemwithandvinyltapesothatthereisnogap.

• Forleftandleftrearpiping,wraptheareawhichaccommodatestherearpiping

housingsectionwithclothtape.

• Forleftandleftrearpiping,bindtheconnectioncabletothetopofthepipewith

vinyltape.

• Forleftandleftrearpiping,bundlethepipinganddrainhosetogetherbywrapping

themwithclothtapeovertherangewithinwhichtheytintotherearpiping

housingsection.

(2) Temporarilyfastentheconnectioncablealongtheconnectionpipewithvinyltape.

(Wraptoabout1/3thewidthofthetapefromthebottomofthepipesothatwater

doesnotenter.)

(3) Fastentheconnectionpipetotheoutsidewallwithasaddle,etc.

(4) Fillthegapbetweentheoutsidewallpipeholeandthepipewithsealersothatrain

waterandwindcannotblowin.

(5) Fastenthedrainhosetotheoutsidewall,etc.

*Locallypurchased

Pipe

Saddle*

Outsidewallcap*

Sealerputty*

(Outdoors)

Wall

Overlaptheinsulation

Vinyltape*

Wrapwithclothtape

Clothtape(accessory)

Drainhose*

Connectioncable

Pipe

Drainhose

Checkthefollowing:

GOOD

Drainhose

Saddle

Liftedup Wave Endinwater

Drainhose Connectionpipe

Wallpipe Connectioncable

Left piping For connection from the left rear

Pipe

Connectionpipe

(heatinsulation)

Indoorunitpipe

(heatinsulation)

PROHIBITED

Bindthepipestogether

sothatthereisnogap.

SealAisusedwhenthediameter

ofgaspipeisØ12.70ormore.

Buttconnectionpipe(heat

insulation)againsttheindoor

unitpipe(heatinsulation)and

wrapwithsealAsothatthere

isnogap.

9333005225_IM_2L.indb 5 10/12/2017 08:48:45

En-6

9. FRONT PANEL REMOVAL AND INSTALLATION

Intake grille removal Intake grille installation

Opentheintake

grille.Whilegently

pressingtheleft

andrightmounting

shaftsoftheintake

grilleoutward“a”,

removetheintake

grilleindirectionof

thearrow“b”.

Whileholdingthe

grillehorizontal,set

theleftandright

mountingshaftsinto

thepillowblocksat

thetopofthepanel

“c”.

Tolatcheachshaft

properly,insertthe

shaftuntilitsnaps.

Press4placeson

theintakegrilleto

closeitcompletely.

9.1. Front panel removal

(1) Removeintakegrille(Refertothe“Intakegrilleremoval”.)

(2) Removewirecover.

(3) Remove6screws.

Screws(6places)

4screws(Donotremove.)

Wirecover

(4) Pullthefrontpaneltothefront,thenraiseittoremove.

Frontpanel

9.2. Front panel installation

(1) First,t thelower part of the frontpanel, and insert top andbottom hooks. (3 top

sides,2center)

Indoorunit

Frontpanel

Latches(2places)

Centerhooks

(2places)

Tophooks

(3places)

Topholes(6places)

(2) Attachthe6screws.

(3) Attachthewirecover.

(4) Attachtheintakegrille.

CAUTION

InstalltheFrontpanelandIntakegrillesecurely.Ifinstallationisimperfect,theFront

panelorIntakegrillemayfalloffandcauseinjury.

10. REMOTE CONTROLLER INSTALLATION

CAUTION

•Checkthattheindoorunitcorrectlyreceivesthesignalfromtheremotecontroller,

theninstalltheremotecontrollerholder.

•Selecttheremotecontrollerholderselectionsitebypayingcarefulattentiontothe

following:

Avoidplacesindirectsunlight.

Selectaplacethatwillnotbeaffectedbytheheatfromastove,etc.

10.1. Remote controller holder installation

•

 Installtheremotecontrolleramaximumdistanceof7mfromtheremotecontrollerre-

ceiver.However,wheninstallingtheremotecontroller,checkthatitoperatescorrectly.

•

I

nstalltheremotecontrollerholdertoawall,pillar,etc.withthetappingscrew.

Remote controller

holder xing

Remote

controllerholder

Tappingscrew

(small)

Remote controller

mounting

Remote

controller

Push

Set

10.2. Remote controller custom setting

Usethefollowingstepstoselectthecustomcodeoftheremotecontroller.(Notethatthe

airconditionercannotreceiveasignaliftheairconditionerhasnotbeensetforthematch-

ingcustomcode.)

(1) Pressthe“START/STOP(

)”buttonuntilonlythe

clockisdisplayedontheremotecontrollerdisplay.

(2) Pressthe“MODE”buttonforatleast5secondstodis-

playthecurrentcustomcode(initiallysettoA).

(3) Pressthe“TEMP.”(

/ )buttonstochangethecus-

tomcodebetween

A↔B↔C↔D

.

Matchthecodeonthedisplaytotheairconditioner

customcode.

(4) Pressthe“MODE”buttonagaintoreturntotheclock

display.Thecustomcodewillbechanged.

•Ifnobuttonsarepressedwithin30secondsafterthecustomcodeisdisplayed,the

systemreturnstotheoriginalclockdisplay.Inthiscase,startagainfromstep1.

•TheairconditionercustomcodeissettoApriortoshipment.

11. OPTIONAL KIT INSTALLATION

Thisairconditionercanbeconnectedwiththefollowingoptionalkits.

• Wiredremotecontroller

• Simpleremotecontroller

• Externalconnectkit

CAUTION

•Beforeinstalling,besuretodisconnectallpowersupply.

•Don’ttouchtheheatexchanger.

•Duringinstallingorremovingoperation,besurenottohavewirecaughtbypartsor

drawithard.Oritmayresulttroublestotheair-conditioner.

•Avoidplaceindirectsunlight.

•Selectplacethatwillnotbeaffectedbytheheatfromastove,etc.

•Beforesettinguptheoptionalkit,pleaseconrmwhetherair-conditionercanreceive

thesignal.

•Donotconnectthewiredremotecontrollertotheterminalforpowersupply.

•Whenconnectingthewiredremotecontrollerwiththeindoorunit,usetheconnecting

cable(suppliedwithwiredremotecontrollerorsimpleremotecontroller).

•Recommendedcablelengthofwiredremotecontrolleris10m.Makesuretoinsulate

theconnectingpartwhenextendingthecable.

• Whenyouusewiredremotecontroller,somefunctionsmaynotbeused.

•

Donotconnectpowersupplywiththeterminal.

INDOORUNIT

PCB

TERMINAL

9333005225_IM_2L.indb 6 10/12/2017 08:48:51

En-7

11.3.

Installing communication box

11.3.1. Removing intake grille

( Refer to “9.1. Front panel removal” )

11.3.2. Removing control box

(1) Removethescrews(x4).(Usethesamescrewswheninstalling.)

(2) Pullthecontrolboxcovertowardsyouandremove.

(1)

(2)

(1)

(3) Removetheconnectors(x4).

• Removeandpulloffthelockatthesideoftheconnectorinsertionpart.

CAUTION

•Becarefulnottodamagethepartsontheboard.

Otherwise,itwillcausemalfunction.

Connectornumber:CN5*

Connectornumber:CN4*

Connectornumber:CN3*

Connectornumber:CN7*

*:Symbolindicatingthelocationprintedontheboard

(4) Removethewiresfromthethreefixtures.(Seethefigurebelow)

• LeavethethickgreenwireinfixtureCandremovetherestofthewires.

CAUTION

•Donotpullthewiresforcibly.Youmaydamagethem.

FixtureA

Before After

FixtureB

FixtureC

(5) Whilepullingthecontrolboxtowardsyou,removeintherightdirection.

• Donotremovethethermistor.

• Donotdamagetheterminalsontheremovedwires.

Thermistor

Controlbox

Terminals

11.1. Remote controller cable modication

(1) Useatooltocutofftheterminalontheendoftheremotecontrollercable,andthen

removetheinsulationfromthecutendofthecable.

(2) Connecttheremotecontrollercableandconnectingcable.

(suppliedwithwiredremotecontroller)

Important:Besuretosolderwirestoconnect.Besuretoinsulatetheconnection

betweenthewires.

Connectingcable

White

Red

White

Red

Black

Insulated

connection

Remote

controllercable

Remote

controllercable

20mm

11.2. Installing wired remote controller terminal /

external connect kit terminal (sold separately)

(1) Removethescrewonthecontrolboxasshownonthetoprightofthefigurebelow.

(2) Releasebothbottomclaspsatthesidesinthedirectionofthearrowascircledin

thebottomleftofthefigurebelow.Pullandremovethecover.

(2)

(1)

Cover

(3) Connectthewiredremotecontrollerterminal/externalconnectkitterminal(sold

separately)tothespecifiedterminalontheboardasshownbelow.Pleaseconnect

totheconnectorwithnecessaryfunctionaccordingtotheactualusage.

(4) Afterconnectingeachterminal,threadthecablesthroughthenotchascircledon

thebottomrightofthefigurebelow.

(3) Controlinput(Operation/

StoporForcedstop)



connector

 :CNA01(White)*

(3) Wiredremotecontroller

connector

 :CNC01(White)*

*:Symbolindicatingthelocationprintedontheboard

(3) ErrorStatusoutput

connector

 :CNB02(Black)*

(3) Operationstatus

outputconnector

 :CNB01(White)*

(4)

(5)Installthecontrolboxcoverasshownbelow.

(Alignthecoverwiththeupperandlowerrightcornersasindicatedbythetriangular

symbolsonthefigure.

Inserttheclaspsonthecoverintobothsidesatthebottomofthetwodotted

circles.)

• Wheninstallingthecontrolboxcover,makesurethatthecablesarenotcaughtas

showninthedetailview.

(6)Installonescrew.

(7)Screwtheearthwireofwiredremotecontrollerasshowninthefigure.(AUSTRALIA

modelonly).

(7)

(5)

(5)(6)Cover

Detailview

9333005225_IM_2L.indb 7 10/12/2017 08:48:53

En-8

Controlbox

(5)

11.3.3. Installing communication box

(1) Installthecommunicationboxonthemainunitandsecureitwiththeprovided

screwatthelocationshownbelow.

ViewA(Detailview)

Screw

Motorcover

ViewA(Detailview)

(2) Usetheholeonthemotorcoverandsecurethewirefromthecommunicationbox

withtheprovidedcabletie(accessoryforoption).

(Seethefigurebelow)

Cabletie

Cutawaythetipof

thecabletie.

Hole

11.3.4. Installing control box

(1) Setthecontrolboxtowardthebottomsothatittouchesthemotorcoverfromthe

right.

Inserttheprotrudingpartofthemain

unitonthexture(1location)into

thecontrolbox.

Controlbox

• Theinstallationmethodofthecontrolboxisdifferentforeachdestinationcountry.

(Wheninstalling,reusethescrewthatwasremovedin11.3.2. Removing control

box.)

(2) Securethecontrolboxwithascrew.(Usealongscrew.)

(3)

(2)

(3) Fastentheearthwiresoftheheatexchangertogetherasshownintheleftfigure

above.(Useashortscrewhere.)

(4) Hitchthewiresontothefixturesasshownintheovalcirclesbelow.Thenconnect

theconnectorsinthesquarestotheterminalsrespectively.

(Eachterminalshouldformapairwithaconnector.)

CAUTION

•Ensurethattheconnectorisproperlyinserted.

Otherwise,itmayresultinerroneousoperation.

•Becarefulnottodamagethepartsontheboard.

Otherwise,itwillcausemalfunction.

(4)

(5) Fastentheearthwire(green)inthecommunicationboxtogetherwiththeearthwire

(green)ontheboardofthecontrolboxasshowninthefollowingfigure.

(5)

(6) Installthecoverofthecontrolboxontotheinnersideoftheribasfollows.

CAUTION

•Donotcutortuckthewireswiththeelectricalcomponentboxcover.

Anelectricshockmayoccurifthewiresaredamaged.

9333005225_IM_2L.indb 8 10/12/2017 08:49:01

En-9

(7) Tightenwithscrewstopreventthecoverofthecontrolboxfromfallingoff.

(Wheninstalling,reusethescrewsthatwasremovedin13.3.2.Removingcontrol

box.)

(7)

(6)

(8) Pasteprotectseals(2locations)topreventthewiresfromstickingout.

(8)

11.3.5. Installing front panel

( Refer to “9.2. Front panel installation” )

12. FUNCTION SETTING

Performthe“FUNCTIONSETTING”accordingtotheinstallationconditionsusingthe

remotecontroller.

CAUTION

•ConrmwhetherthewiringworkforOutdoorunithasbeennished.

•Conrmthatthecoverfortheelectricalenclosureontheoutdoorunitisinplace.

• Thisprocedurechangesthefunctionsettingsusedtocontroltheindoorunitaccording

totheinstallationconditions.Incorrectsettingscancausetheindoorunittomalfunction.

• Afterthepoweristurnedon,performthe“FUNCTIONSETTING”accordingtothe

installationconditionsusingtheremotecontroller.

• Thesettingsmaybeselectedbetweenthefollowingtwo:FunctionNumberorSetting

Value.

• Settingswillnotbechangedifinvalidnumbersorsettingvaluesareselected.

• Refertotheinstallationmanualenclosedwiththeremotecontrollerwhenthewired

remotecontroller(option)isused.

Entering the Function Setting Mode

WhilepressingthePOWERFULbuttonandSETTEMP.( )simultaneously,pressthe

RESETbuttontoenterthefunctionsettingmode.

STEP 1

Selecting the Remote Controller Custom Code

UsethefollowingstepstoselectthecustomcodeoftheRemoteController.(Notethatthe

airconditionercannotreceiveasignaliftheairconditionerhasnotbeensetforthematch-

ingcustomcode.)

Thecustomcodesthataresetthroughthisprocessareapplicableonlytothesignalsin

theFUNCTIONSETTING.Fordetailsonhowtosetthecustomcodesthroughthenormal

process,referto“Remotecontrollercustomcode”.

(1) Press SETTEMP. (

 / ) button to change the custom

codebetween

A↔B↔C↔D

.Matchthecodeonthe

displaytotheairconditionercustomcode.(initiallysettoA)

(Ifthecustomcodedoesnotneedtobeselected,pressthe

10°CHEATbuttonandproceedtoSTEP2.)

(2) PresstheMODEbuttonandcheckthattheindoorunitcan

receivesignalsatthedisplayedcustomcode.

(3) Pressthe10°C HEAT button to accept the customcode,

andproceedtoSTEP2.

TheairconditionercustomcodeissettoApriortoshipment.

STEP 2

Selecting the Function Number and Setting Value

(1) PresstheSETTEMP.( / )buttonstoselectthe

functionnumber.(Pressthe10

°C

HEATbuttonto

switchbetweentheleftandrightdigits.)

(2) Pressthe

POWERFUL

buttontoproceedtosetting

value.(Press the

POWERFUL

button again to return

tothefunctionnumberselection.)

(3) PresstheSETTEMP.(

/ )buttonstoselectthe

settingvalue.(Pressthe10

°C

HEATbuttontoswitch

betweentheleftandrightdigits.)

(4) PresstheMODEbutton,andSTART/STOPbutton,in

theorderlistedtoconrmthesettings.

(5) PresstheRESETbuttontocancelthefunctionset-

tingmode.

(6) AftercompletingtheFunctionSetting,besuretodis-

connectthepowersupplyandthenreconnectit.

CAUTION

Afterdisconnectingthepowersupply,wait30secondsormorebeforereconnectingit.

TheFunctionSettingwillnotbecomeactiveunlessthepowersupplyisdisconnected

andthenreconnected.

Filter sign

Selectappropriateintervalsfordisplayingtheltersignontheindoorunitaccordingtothe

estimatedamountofdustintheairoftheroom.

Iftheindicationisnotrequired,select“Noindication”(03).

(♦...Factorysetting)

Function

Number

Setting

Value

Setting Description

00 Standard(400hours)

01 Longinterval(1,000hours)

02 Shortinterval(200hours)

03 Noindication ♦

Room temperature sensor control for cooling

Dependingontheinstalledenvironment,correctionoftheroomtemperaturesensormay

berequired.

Selecttheappropriatecontrolsettingaccordingtotheinstalledenvironment.

(♦...Factorysetting)

Function

Number

Setting

Value

Setting Description

00 Standard ♦

01 Slightlylowercontrol

02 Lowercontrol

03 Highercontrol

Room temperature sensor control for heating

Dependingontheinstalledenvironment,correctionoftheroomtemperaturesensormay

berequired.

Selecttheappropriatecontrolsettingaccordingtotheinstalledenvironment.

(♦...Factorysetting)

Function

Number

Setting

Value

Setting Description

00 Standard ♦

01 Lowercontrol

02 Slightlyhighercontrol

03 Highercontrol

Auto restart

Enableordisableautomaticrestartafterapowerinterruption.

(♦...Factorysetting)

Function

Number

Setting

Value

Setting Description

00 Enable ♦

01 Disable

*Autorestartisanemergencyfunctionsuchasforpoweroutageetc.Donotattemptto

usethisfunctioninnormaloperation.Besuretooperatetheunitbyremotecontrolleror

externaldevice.

Function Number

Setting

Value

9333005225_IM_2L.indb 9 10/12/2017 08:49:03

En-10

Room temperature sensor switching

(Onlyforwiredremotecontroller)

WhenusingtheWiredremotecontrollertemperaturesensor,changethesettingto“Both”(01).

(♦...Factorysetting)

Function

Number

Setting

Value

Setting Description

00 Indoorunit ♦

01 Both

00:Sensorontheindoorunitisactive.

01:Sensorsonbothindoorunitandwiredremotecontrollerareactive.

*

Remotecontrollersensormustbeturnedonbyusingtheremotecontroller.

Remote controller custom code

(Onlyforwirelessremotecontroller)

Theindoorunitcustomcodecanbechanged.Selecttheappropriatecustomcode.

(♦...Factorysetting)

Function

Number

Setting

Value

Setting Description

00 A ♦

01 B

02 C

03 D

External input control

“Operation/Stop”modeor“Forcedstop”modecanbeselected.

(♦...Factorysetting)

Function

Number

Setting

Value

Setting Description

00 Operation/Stopmode ♦

01 (Settingprohibited)

02 Forcedstopmode

Room temperature sensor switching (Aux.)

Tousethetemperaturesensoronthewiredremotecontrolleronly,changethesettingto“Wired

remotecontroller”(01).Thisfunctionwillonlyworkifthefunctionsetting42issetat“Both”(01)

(♦...Factorysetting)

Function

Number

Setting

Value

Setting Description

00 Both ♦

01 Wiredremotecontroller

Indoor unit fan control for energy saving for cooling

Enablesordisablesthepower-savingfunctionbycontrollingtheindoorunitfanrotationwhen

theoutdoorunitisstoppedduringcoolingoperation.

(♦...Factorysetting)

Function

Number

Setting

Value

Setting description

00 Disable

01 Enable ♦

00:Whentheoutdoorunitisstopped,theindoorunitfanoperatescontinuouslyfollowing

thesettingontheremotecontroller.

01:Whentheoutdoorunitisstopped,theindoorunitfanoperatesintermittentlyatavery

lowspeed.

Setting record

Recordanychangestothesettingsinthefollowingtable.

Setting Description Setting Value

Filtersign

Roomtemperaturesensorcontrolforcooling

Roomtemperaturesensorcontrolforheating

Autorestart

Roomtemperaturesensorswitching

Remotecontrollercustomcode

Externalinputcontrol

Roomtemperaturesensorswitching(Aux.)

Indoorunitfancontrolforenergysavingforcooling

AftercompletingtheFunction Setting,besure todisconnectthe powersupplyand then

reconnectit.

13. TEST RUN

Check items

(1) Isoperationofeachbuttonontheremotecontrollernormal?

(2) Doeseachlamplightnormally?

(3) Doairowdirectionlouversoperatenormally?

(4) Isthedrainnormal?

(5) Donothaveanabnormalnoiseandvibrationduringoperation?

•

 Donotoperatetheairconditionerintestrunforalongtime.

[Operation method]

•

 Fortheoperationmethod,refertotheoperatingmanual.

•

 Theoutdoorunit,maynotoperate,dependingontheroomtemperature.Inthis

case,keeponpressingtheMANUALAUTObuttonoftheindoorunitformorethan

10seconds.Theoperationindicatorlampandtimerindicatorlampwillbegintoash

simultaneouslyduringcoolingtestrun.Then,heatingtestrunwillbegininaboutthree

minuteswhenHEATisselectedbytheremotecontroloperation.(Pleasefollowthe

operatingmanualforremotecontroloperation.)

•

 Toendtestoperation,presstheremotecontrollerSTART/STOPbutton.

(Whentheairconditionerisrunningbypressingthetestrunbutton,theOPERATION

LampandTIMERLampwillsimultaneouslyashslowly.)

[Using the wired remote controller] (Option)

Fortheoperationmethod,refertotheoperatingmanual.

(1) Stoptheairconditioneroperation.

(2) Pressthemastercontrolbuttonandthefancontrolbuttonsimultaneouslyfor2

secondsormoretostartthetestrun.

Testrundisplay

(3) Pressthestart/stopbuttontostopthetestrun.

14. CUSTOMER GUIDANCE

Explainthefollowingtothecustomerinaccordancewiththeoperatingmanual:

(1)Startingandstoppingmethod,operationswitching,temperatureadjustment,timer,air-

owswitching,andotherremotecontrolleroperations.

(2)Airlterremovalandcleaning,andhowtousetheairlouvers.

(3)Givetheoperatingmanualtothecustomer.

9333005225_IM_2L.indb 10 10/12/2017 08:49:03

En-11

15. ERROR CODES

Ifyouuseawirelessremotecontroller,thelamponthephotodetectorunitwilloutputerror

codesbywayofblinkingpatterns.Ifyouuseawiredremotecontroller,errorcodeswillap-

pearontheremotecontroldisplay.Seethelampblinkingpatternsanderrorcodesinthe

table.Anerrordisplayisdisplayedonlyduringoperation.

Error display

Error code Description

OPERATION

lamp

(green)

TIMER

lamp

(orange)

ECONOMY

lamp

(green)

●

(1)

●

(1)

◊

Serialcommunicationerror

●

(1)

●

(2)

◊

•Wiredremotecontroller

communicationerror

•Serverroomcontrol

communicationerror

●

(1)

●

(5)

◊

Checkrununfinished

●

(1)

●

(6)

◊

PeripheralunittransmissionPCB

connectionerror

●

(1)

●

(8)

◊

Externalcommunicationerror

●

(2)

●

(1)

◊

UnitnumberorRefrigerantcircuit

addresssettingerror

[SimultaneousMulti]

●

(2)

●

(2)

◊

Indoorunitcapacityerror

●

(2)

●

(3)

◊

Combinationerror

●

(2)

●

(4)

◊

•Connectionunitnumbererror

(indoorsecondaryunit)

[SimultaneousMulti]

•Connectionunitnumbererror

(indoorunitorbranchbox)

[FlexibleMulti]

●

(2)

●

(6)

◊

Addresssettingerrorinwired

remotecontrollersystem

●

(2)

●

(7)

◊

Primaryunit,secondaryunitset-

uperror[SimultaneousMulti]

●

(3)

●

(2)

◊

IndoorunitPCBmodel

informationerror

●

(3)

●

(5)

◊

Manualautoswitcherror

●

(4)

●

(1)

◊

Roomtemp.sensorerror

●

(4)

●

(2)

◊

IndoorunitHeatEx.Middletemp.

sensorerror

●

(5)

●

(1)

◊

Indoorunitfanmotor1error

(Mainfan)

●

(5)

●

(3)

◊

Drainpumperror

●

(5)

●

(4)

◊

ElectricaircleanerreverseVDD

error

●

(5)

●

(5)

◊

Filterseterror

●

(5)

●

(7)

◊

Dampererror

●

(5)

●

(8)

◊

Intakegrilleerror

●

(5)

●

(9)

◊

Indoorunitfanmotor2error

(Leftsidefan)

●

(5)

●

(10)

◊

Indoorunitfanmotor3error

(Rightsidefan)

●

(5)

●

(15)

◊

Indooruniterror

●

(6)

●

(2)

◊

OutdoorunitmainPCBmodel

informationerroror

communicationerror

●

(6)

●

(3)

◊

Invertererror

●

(6)

●

(4)

◊

Activefiltererror,PFCcircuiterror

●

(6)

●

(5)

◊

TripterminalLerror

●

(6)

●

(8)

◊

Outdoorunitrushcurrentlimiting

resistertemp.riseerror

Error display

Error code Description

OPERATION

lamp

(green)

TIMER

lamp

(orange)

ECONOMY

lamp

(green)

●

(6)

●

(10)

◊

DisplayPCBmicrocomputers

communicationerror

●

(7)

●

(1)

◊

Dischargetemp.sensorerror

●

(7)

●

(2)

◊

Compressortemp.sensorerror

●

(7)

●

(3)

◊

OutdoorunitHeatEx.liquidtemp.

sensorerror

●

(7)

●

(4)

◊

Outdoortemp.sensorerror

●

(7)

●

(5)

◊

SuctionGastemp.sensorerror

●

(7)

●

(6)

◊

•2-wayvalvetemp.sensorerror

•3-wayvalvetemp.sensorerror

●

(7)

●

(7)

◊

Heatsinktemp.sensorerror

●

(8)

●

(2)

◊

•Sub-coolHeatEx.gasinlet

temp.sensorerror

•Sub-coolHeatEx.gasoutlet

temp.sensorerror

●

(8)

●

(3)

◊

Liquidpipetemp.sensorerror

●

(8)

●

(4)

◊

Currentsensorerror

●

(8)

●

(6)

◊

•Dischargepressuresensorerror

•Suctionpressuresensorerror

•Highpressureswitcherror

●

(9)

●

(4)

◊

Tripdetection

●

(9)

●

(5)

◊

Compressorrotorposition

detectionerror

●

(9)

●

(7)

◊

Outdoorunitfanmotorerror

●

(9)

●

(9)

◊

4-wayvalveerror

●

(10)

●

(1)

◊

Dischargetemp.error

●

(10)

●

(3)

◊

Compressortemp.error

●

(10)

●

(4)

◊

Highpressureerror

●

(10)

●

(5)

◊

Lowpressureerror

●

(13)

●

(2)

◊

Branchboxeserror

[FlexibleMulti]

Displaymode

●

:0.5sON/0.5sOFF

◊

:0.1sON/0.1sOFF

():Numberofflashing

[Troubleshooting with the indoor unit display]

OPERATIONindicator(green)

TIMERindicator(orange)

ECONOMYindicator(green)

[Troubleshooting with the Wired Remote Controller Display (Option)]

Ifan error occurs, the followingdisplaywill be shown. (“Er” willappear in the set room

temperaturedisplay.)

Errorcode

9333005225_IM_2L.indb 11 10/12/2017 08:49:12

9333005225_IM_2L.indb 12 10/12/2017 08:49:12

Fujitsu ASYG07LMCE-R Installation guide

Brand: Fujitsu

Model: ASYG07LMCE-R

Category: Split-system air conditioners

Type: Installation guide

This manual is also suitable for

Download PDF

report

Fujitsu ASYG07LMCE-R Installation guide

This manual is also suitable for

Fujitsu ASYG07LMCE-R Installation guide

Related papers

Other documents