ADTRAN 239 H4R is a device used to extend the reach of HDSL4 circuits. It can be used in a variety of applications, including:
- Extending the reach of HDSL4 circuits to remote locations
- Providing backup for HDSL4 circuits
- Increasing the capacity of HDSL4 circuits
The 239 H4R is a compact and lightweight device that is easy to install and maintain. It is also very reliable, making it an ideal choice for mission-critical applications.
Here are some of the key features of the 239 H4R:
- Supports HDSL4 data rates up to 2.3 Mbps
- Can be used to extend the reach of HDSL4 circuits up to 16 kft
ADTRAN 239 H4R is a device used to extend the reach of HDSL4 circuits. It can be used in a variety of applications, including:
- Extending the reach of HDSL4 circuits to remote locations
- Providing backup for HDSL4 circuits
- Increasing the capacity of HDSL4 circuits
The 239 H4R is a compact and lightweight device that is easy to install and maintain. It is also very reliable, making it an ideal choice for mission-critical applications.
Here are some of the key features of the 239 H4R:
- Supports HDSL4 data rates up to 2.3 Mbps
- Can be used to extend the reach of HDSL4 circuits up to 16 kft
JOBAID
239 H4R
CLEI: T1R5YP3D_ _
239 H4R
1221445L1
LP1
NET
LP2
LP1
LP2
LL RL
(Y) (G)
/
CUST
61221445L1-22B
0205
CARD EDGE PIN ASSIGNMENTS
LOOPBACK AND CONTROL CODES
Refer to the Installation and Maintenance Practice of the H4TU-C or H4TU-R used in
the circuit for a list of loopback codes.
■ For a complete Installation and Maintenance Practice (P/N 61221445L1-5) faxback: (877) 457-5007, faxback Document 755. Please have your fax number ready. ■
C A U T I O N C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
STATUS LEDs
LP1/LP2 NET ●● Off No span power present
● Solid Green Synchronized with an SNR margin greater than the user defined SNR
Margin Alarm Threshold
✷ Fast Blinking (Blinking 3 times per second) Attempting to synchronize with the
Green H4TU-C
✷ Slow Blinking (Blinking 1 time per second) Synchronized with an SNR margin
Green greater than the user defined SNR Margin Alarm Threshold and the
pulse attenuation is greater than the user defined Loop Attenuation
Alarm Threshold
● Solid Yellow Synchronized with an SNR margin greater than 0 dB but less than
the user defined SNR Margin Alarm Threshold
✷ Slow Blinking Synchronized with an SNR margin greater than 0 dB but less than the
Yellow user defined SNR Margin Alarm Threshold and the pulse attenuation
is greater than the user defined Loop Attenuation Alarm Threshold
● Solid Red Synchronized with an SNR margin of 0 dB
✷ Slow Blinking (Blinking 1 time per second) Synchronized with an SNR margin of 0 dB
Red and the pulse attenuation is greater than the user defined Loop
Attenuation Alarm Threshold
LP1/LP2 CUST ●●Off No span power present
● Solid Green Synchronized with an SNR margin greater than the user defined SNR
Margin Alarm Threshold
✷ Fast Blinking (Blinking 3 times per second) Attempting to synchronize with the
Green H4TU-R
✷ Slow Blinking (Blinking 1 time per second) Synchronized with an SNR margin
Green greater than the user defined SNR Margin Alarm Threshold and the
pulse attenuation is greater than the user defined Loop Attenuation
Alarm Threshold
● Solid Yellow Synchronized with an SNR margin greater than 0 dB but less than the
user defined SNR Margin Alarm Threshold
✷ Slow Blinking Synchronized with an SNR margin greater than 0 dB but less than the
Yellow user defined SNR Margin Alarm Threshold and the pulse attenuation
is greater than the user defined Loop Attenuation Alarm Threshold
● Solid Red Synchronized with an SNR margin of 0 dB
✷ Slow Blinking (Blinking 1 time per second) Synchronized with an SNR margin of 0 dB
Red and the pulse attenuation is greater than the user defined Loop
Attenuation Alarm Threshold
LL/RL ● Green Indicates a loopback at the H4R toward the H4TU-R is active
● Yellow Indicates a loopback at the H4R toward the H4TU-C is active
✷ Blinking Armed but not in loopback.
Yellow
Pin No. Designation Description Pin No. Designation Description
1 GND Ground 7 NC No Connection
2 NC No Connection 8 T Network Loop 2 Tip
3 T1 Customer Loop 1 Tip 9 R Network Loop 2 Ring
4 R1 Customer Loop 1 Ring 10 GND Ground
5 T1 Network Loop 1 Tip 11 T Customer Loop 2 Tip
6 R1 Network Loop 1 Ring 12 R Customer Loop 2 Ring
#61221445L1-22B#
239 H4R
HDSL4 LOOP SPECIFICATIONS
FOR OPTIMUM OPERATION
NOTE: The H4TU-Cs P/N 1221401L6, 1221403L6, 1221404L6 support only one H4R in the HDSL4
circuit.
■ HDSL4 circuit containing no H4Rs will reach up to 16 kft on the local loop (24
AWG)
■ HDSL4 circuit containing one H4R will reach up to 16 kft on the first segment and
15 kft on the second segment (24 AWG).
■ HDSL4 circuit containing two H4Rs will reach to 13.5 kft on the first segment, 14 kft
on the second segment, and 15 kft on the third segment (24 AWG). *
NOTE: Refer to the H4TU-C or H4TU-R Installation and Maintenance Practice, Section HDSL4,
Deployment Guidelines, for other loop parameters including Insertion Loss, Pulse
Attenuation, and Resistance Budgets for span powering
*This is one example of a circuit with 2 H4Rs. Other loop length configurations are
possible in compliance with loop resistance restraints. Refer to the H4R Installation
and Maintenance Practice, Section HDSL4 Deployment Guidelines, for other loop
parameters including Insertion Loss, Pulse Attenuation, and Resistance Budgets for
span powering.
UNIT RESISTANCE
Measurements are with no power applied
The H4R Tip-to-Ring resistance is approximately 6 Ω for each pair.
COMPLIANCE
This product complies with UL 60950, third edition. It is intended for
installation in restricted access locations only and in equipment with a Type “B” or
“E” installation code. Ensure chassis ground is properly connected.
WARRANTY
Warranty for Carrier Networks products manufactured by ADTRAN and supplied
under Buyer’s order for use in the U.S. is ten (10) years. For a complete copy of
ADTRAN’s U.S. and Canada Carrier Networks Equipment Warranty
(P/N 60000087-10): call (877) 457-5007, faxback Document 414.
H4TU-C VMDF H4R1 H4R2 H4TU-R
TURNUP & TROUBLESHOOTING GUIDE
PRICING AND AVAILABILITY 800.827.0807
TECHNICAL SUPPORT 800.726.8663
RETURN FOR REPAIR 256.963.8722
www.adtran.com
61221445L1-22B
239 H4R Capacity Guidelines for ADTRAN Housings
PART No. Description CLEI CODE Slot Stub H4R Capacity Material
Above Below
Ground Ground
1150027L1 239/439 Housing DDMOABA1MA 4 Air 4 4 Stainless/Poly
1150027L2 239/439 Housing DDMOBBA1MA 4 Gel 4 4 Stainless/Poly
1152010L3 239/439 Housing DDMOBAE1RA 2 Gel 2 2 Polymer
1152010L4 239/439 Housing DDMOAAE1RA 2 Air 2 2 Polymer
1150057L1 Universal Housing DDMODAO1RA 4 Air 4 4 Stainless Steel
1150057L2 Universal Housing DDMOCAO1RA 4 Gel 4 4 Stainless Steel
1150058L1 Universal Housing DDMOEEO1RA 8 Air 8 8 Stainless Steel
1150058L2 Universal Housing DDMOFE01RA 8 Gel 8 8 Stainless Steel
1190816L1 16-Slot BG Housing DDMOES0IRA 16 Air 16 16 Stainless Steel
1190816L2 16-Slot AG Housing DDMOFS0IRA 16 Gel 16 16 Stainless Steel
1190816L3 16-Slot AG Housing DDMOMS01RA 16 Air 16 16 Stainless Steel
239 H4R Capacity Guidelines for Other Housings
Manufacturer Description Manufacturer’s Part Number Slot Stub H4R Capacity Material
Above Below
Ground Ground
ADC Radiator II SPX-HRXC-30-AG-016GT 16 Air 16 16 Stainless Steel
ADC Radiator II SPX-HRXC-30-BG-016GT 16 Gel 16 16 Stainless Steel
ADC Radiator SPX-HRXC-30-B1 8 Air 8 8 Stainless Steel
Circa Telecom HDSL-12A 760005 12 Air 12 12 Polymer
Circa Telecom HDSL-12B 760006 12 Gel 12 12 Polymer
Arris Keptel
®
Inter Link
™
809 RF809A3-XXX or RF809B3-XXX 12 Gel 8
1
N/A Polymer
Arris Keptel
®
Inter Link
™
818/819 RF819A1 or RF819A2 25 Air 12
2
16
3, 4
Polymer
Arris Keptel
®
Inter Link
™
818/819 RF819B1 or RF819B2 25 Gel 12
2
16
3, 4
Polymer
Arris Keptel
®
Inter Link
™
RF820AX or
820 Family RF820BX 2-8 Air Full Full Polymer
Arris Keptel
®
Inter Link
™
RF820AX or
820 Family RF820BX 2-8 Gel Full Full Polymer
1
The recommended 8 slot assignments for above ground installation are as follows: 1, 3, 4, 6, 7, 9, 10, 12.
2
The recommended 12 slot assignments for above ground installation are as follows: Chamber 1: 1, 4, 7, 8, 11, 14 and Chamber 2: 15, 17, 19, 20, 23, 25
3
For 16 slot use, the ambient air temperature measured 1 ft away and parallel to the housing should not exceed 115ºF (46.1ºC).
4
The recommended 16 slot assignments for below ground installation are as follows: Chamber 1: 1, 3, 5, 7, 8, 10, 12, 14 and Chamber 2: 15, 16, 18, 19, 20, 22,
24, 25
Code Input Output
Power Code (PC) C C
Telecommunication Code (TC) X X
Installation Code (IC) A –
First Segment
Second Segment Third Segment
-
1
-
2
ADTRAN 239 H4R is a device used to extend the reach of HDSL4 circuits. It can be used in a variety of applications, including:
- Extending the reach of HDSL4 circuits to remote locations
- Providing backup for HDSL4 circuits
- Increasing the capacity of HDSL4 circuits
The 239 H4R is a compact and lightweight device that is easy to install and maintain. It is also very reliable, making it an ideal choice for mission-critical applications.
Here are some of the key features of the 239 H4R:
- Supports HDSL4 data rates up to 2.3 Mbps
- Can be used to extend the reach of HDSL4 circuits up to 16 kft
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
ADC HDSL4 User manual
-
-
Lincoln Electric 11018M User manual
-
ADC LTPH-UM-1261-01 User manual
-
3M 965DPS User manual
-
Paradyne Hotwire 8335 User manual
-
-
-
Paradyne ATM Line Cards 8955 User manual
-
Paradyne 8975 User manual
