ADTRAN HRE/T200 Turn-Up Manual

ADTRAN
Brand
ADTRAN
Model
HRE/T200
Category
Motorcycle Accessories
Type
Turn-Up Manual

ADTRAN HRE/T200 is a high-speed digital subscriber line (HDSL) repeater, designed to extend the reach and performance of HDSL circuits. The HRE/T200 operates at speeds up to 2.048 Mbps and can be used to extend the range of HDSL circuits up to 12,000 feet. The HRE/T200 is also equipped with a number of features that make it easy to use and manage, including:

  • Automatic gain control (AGC) to maintain a consistent signal level
  • Echo cancellation to reduce signal reflections
  • Line fault detection to identify problems with the HDSL circuit
  • Status LEDs to indicate the operating status of the HRE/T200

ADTRAN HRE/T200 is a high-speed digital subscriber line (HDSL) repeater, designed to extend the reach and performance of HDSL circuits. The HRE/T200 operates at speeds up to 2.048 Mbps and can be used to extend the range of HDSL circuits up to 12,000 feet. The HRE/T200 is also equipped with a number of features that make it easy to use and manage, including:

  • Automatic gain control (AGC) to maintain a consistent signal level
  • Echo cancellation to reduce signal reflections
  • Line fault detection to identify problems with the HDSL circuit
  • Status LEDs to indicate the operating status of the HRE/T200
HRE T200
HRE / T200
CLEI: T1R6DTTD_ _
JOBAID
STATUS LEDs
PWR ●● OFF No span power is present
● GREEN Span power is present
NET LP1/NET LP2
●● OFF No sync with the HTU-C on NET LP1/LP2
● GREEN Sync with good signal quality
● YELLOW Sync with marginal signal quality
● RED Sync with poor signal quality
CUST LP1/CUST LP2
●● OFF No sync with the HTU-R on CUST LP1/LP2
● GREEN Sync with good signal quality
● YELLOW Sync with marginal signal quality
● RED Sync with poor signal quality
LL/RL
● YELLOW HRE network loopback is active
● GREEN HRE customer loopback is active
LOOPBACK
■ During a loopback toward the network all NET and CUST LP1/LP2
LEDs remain solid. LBK LED is solid yellow.
■ During a loopback toward the customer all NET and CUST LP1/LP2
LEDs remain solid. LBK LED is GREEN. The DSI LED on the HTU-R
flashes during this loopback.
CARD EDGE PIN ASSIGNMENTS
1 Chassis Ground
5 HDSL Loop 1 Tip (Customer)
7 HDSL Loop 1 Tip (Network)
11 Chassis Ground
13 HDSL Loop 1 Ring (Network)
15 HDSL Loop 1 Ring (Customer)
17 –48 V Return (Ground)
27 Chassis Ground
41 HDSL Loop 2 Tip (Network)
47 HDSL Loop 2 Ring (Network)
49 HDSL Loop 2 Ring (Customer)
55 HDSL Loop 2 Tip (Customer)
WIRING DIAGRAM FOR HDSL TECHNOLOGY
CP1 Circuit Pack Cable / Color For HDSL / HRE
/Pin # Wire Housing T400 / T200
5-15 Blue White Customer, Loop 1
7-13 Orange Red Network, Loop 1
41-47 Orange White Network, Loop 2
49-55 Green Red Customer, Loop 2
CP2
5-15 Green White Customer, Loop 1
7-13 Brown Red Network, Loop 1
41-47 Brown White Network, Loop 2
49-55 Slate Red Customer, Loop 2
CP3
5-15 Blue Red Customer, Loop 1
7-13 Blue Black Network, Loop 1
41-47 Orange Black Network, Loop 2
49-55 Blue Yellow Customer, Loop 2
CP4
5-15 Green Black Customer, Loop 1
7-13 Yellow Orange Network, Loop 1
41-47 Brown Black Network, Loop 2
49-55 Slate Black Customer, Loop 2
Order Wires Slate White
Spare Pair Green Yellow
Note: Wiring information is for housing 1150043L1, L2 (L1– aircore cable, L2– gel-filled core cable).
ADTRAN T200/T400 REPEATER HOUSINGS
Part # Description HRE Capacity CLEI CODE* Material
1150090L1 24-slot Pad Mount Gel Stub 24 T1MJ4U0MRA Aluminum
1150090L2 24-slot Pole Mount Gel Stub 24 T1MJ5UOMRA Aluminum
1150043L1 4-slot Air Stub 4 DDMOAD01MA Stainless Steel Dome
1150043L2 4-slot Gel Stub 4 DDMOBD01MA Stainless Steel Dome
61246041L1-22A
0002
■ For a complete Installation and Maintenance Practice faxback: (877) 457-5007, Document 453. Please have your fax number available. ■
C A U T I O N
C A U T I O N
!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
PRICING AND AVAILABILITY 800.827.0807
TECHNICAL SUPPORT 800.923.8726
RETURN FOR REPAIR 256.963.8722
www.adtran.com
61246041L1-22A
T200 HRE TURN-UP GUIDE
LOOP BACK
LOOP THRU
SHORT
OPEN
LOOP 1
LOOP 2
P7 T
P13 R
P41 T
P47 R
TP5
R P15
T P55
R P49
CUST
NET
LOOP 1
LOOP 2
P7 T
P13 R
P41 T
P47 R
TP5
R P15
T P55
R P49
CUST
NET
LOOP 1
LOOP 2
P7 T
P13 R
P41 T
P47 R
TP5
R P15
T P55
R P49
CUST
NET
LOOP 1
LOOP 2
P7
P5
T
NET
CUST
P13
P15
R
T
R
LOOP
BACK
LOOP
THRU
SHORT
OPEN
SW1
P41
P55
T
NET
CUST
P47
P49
R
T
R
P17
P1/P11
FRM
GND
-48
RET
P35
-48V
1996
5244.065-1D
c
LOOP 1
LOOP 2
P7 T
P13 R
P41 T
P47 R
TP5
R P15
T P55
R P49
CUST
NET
INSERTING THE TAC
For test access using the TAC, insert the TAC into the repeater housing as follows.
Hold card with the index finger through the finger hole viewing the edge of the card
so that SW1 is facing to the right. The edge of the card being viewed corresponds to
the faceplate of the HRE. Insert card into the slot with the same orientation as the
T200 HRE. Test Access Card (TAC), part number 1244065L1, or Test Access Module
(TAM), part number 1245065L1, can be used for testing the slot.
TESTING THE CO PAIRS
LOOPBACK
1. To loopback the circuit put SW1 in the LOOPBACK position. This loops the circuit
back to the CO and to the field.
LOOPTHRU
2. To loopthru the CO pairs to the field pairs put SW1 in the LOOPTHRU position.
This bridges the circuit pairs.
SHORT
3. To short the CO pairs put SW1 in the SHORT position. This connects transmit to
receive on each loop.
OPEN
4. To open the circuit put SW1 in the OPEN position. This allows for a voltage
measurement across pairs.
AVAILABLE ACCESS
Label Description
P7 LOOP1 Transmit towards NET
P13 LOOP 1 Receive towards CUST
P5 LOOP 1 Transmit towards CUST
P15 LOOP 1 Receive towards CUST
P41 LOOP 2 Transmit towards NET
P47 LOOP 2 Receive towards NET
P55 LOOP 2 Transmit towards CUST
P49 LOOP 2 Receive towards CUST
P17 –48RET
P1 Frame Ground
P11 Frame Ground
P35 –48 volts
WARRANTY
Warranty for Carrier Networks products manufactured by ADTRAN and supplied under Buyer’s
order for use in the U.S. is ten (10) years. For a complete faxback copy of ADTRAN’s U.S. and
Canada Carrier Networks Equipment Warranty: (877) 457-5007, Document 414.
COMPLIANCE
This product complies with UL 1950, third edition. It is
intended for installation in restricted access locations only and
in equipment with a Type “B”’ or “E” installation code. Ensure
chassis ground is properly connected.
Code Input Output
Power Code (PC) C C
Telecommunication Code (TC) X X
Installation Code (IC) A –
  • Page 1 1
  • Page 2 2

ADTRAN HRE/T200 Turn-Up Manual

ADTRAN
Brand
ADTRAN
Model
HRE/T200
Category
Motorcycle Accessories
Type
Turn-Up Manual

ADTRAN HRE/T200 is a high-speed digital subscriber line (HDSL) repeater, designed to extend the reach and performance of HDSL circuits. The HRE/T200 operates at speeds up to 2.048 Mbps and can be used to extend the range of HDSL circuits up to 12,000 feet. The HRE/T200 is also equipped with a number of features that make it easy to use and manage, including:

  • Automatic gain control (AGC) to maintain a consistent signal level
  • Echo cancellation to reduce signal reflections
  • Line fault detection to identify problems with the HDSL circuit
  • Status LEDs to indicate the operating status of the HRE/T200
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents