Whirlpool AKR 608 IX Program Chart

Brand: Whirlpool

Model: AKR 608 IX

Category: Cooker hoods

Type: Program Chart

This manual is also suitable for

Whirlpool AKR 608 IX offers efficient odor and grease removal with its powerful extraction system, making it ideal for medium-sized kitchens. The two-speed fan lets you adjust the extraction power to your cooking needs, while the aluminum grease filter effectively traps grease particles. Its slim profile and elegant design make it a stylish addition to any modern kitchen.

5019 318 33182

D F NL E

P IGR

INSTALLATION AND USE

For installation:

The hood must be installed at least 65 cm from electric cookers and 75 cm from gas, gas oil or

coal cookers. If the installation instructions for a gas cooker specify a greater distance, then this distance must be

observed.

For installation and use:

Before installing or using the hood, read this manual carefully. The drawings are at the

front of the manual. The Manufacturer declines all liability for any faults, damage or fires caused by the appliance

as a result of failure to observe the instructions and recommendations given in this manual.

To install, follow steps (1

.....). Do not connect the appliance to the electrical power supply until

installation is completed. If the exhaust pipe is not provided, it must be purchased separately.

1. Control panel

2. Extractor grille or grease filter/s (on some models the filter is behind the grille)

3. Lighting unit

4. Grease filter surround (selected models only)

31833182.fm Page 5 Wednesday, November 16, 2005 4:56 PM

5019 318 33182

D F NL E

P IGR

The discharge air must not be ducted to a flue used for removing fumes produced by appliances using gas or other fuels,

but must have a separate outlet. All national regulations governing extraction of fumes must be observed.

Extractor surface release

For selected models: 292 - 515

Measurements in proportion to hood size

For selected models:

tighten the screws of the fixing clips to the

wall unit

Secure using the screws provided

Present on some models

To fit the grill,

use components

31833182.fm Page 6 Wednesday, November 16, 2005 4:56 PM

5019 318 33182

D F NL E

P IGR

REPLACING BULBS:

1. Disconnect the electrical power supply.

2. Remove the grease filter support grille (

Fig. 2

) or the grease filter

to access the lamp housing (

Fig. 1

). On some models the lamp

cover can simply be prised off using standard screwdriver (

A -

Fig. 1

3. Remove the burnt-out bulb.

Replace using 40 W max E14 bulbs only.

4. Refit the extractor grille or lighting unit.

REMOVING AND REPLACING OR CLEANING

THE GREASE FILTER:

1. Disconnect the electrical power supply.

2. Remove the extractor grilles or the grease filters - using parts

, (

Fig. 1

3. Release the grease filter (selected models -

Fig. 3

4. Remove the dirty grease filter.

5. After the grease filter has been replaced or cleaned (depending on

model), refit the parts in reverse order, making sure the entire

extraction surface is covered.

FITTING OR REPLACING THE CARBON FILTER:

1. Disconnect the electrical power supply.

2. Remove the extractor grilles or the grease filters (

Fig. 1

) or the

surround (

Fig. 2

3. Rectangular filter: position the filter

so that it covers the motor

protection grille and turn the knob clockwise. To release,

proceed in reverse order.

Round filter: Insert the carbon filter over the motor protection

grille, on some models the reference mark

must line up with

the arrow

printed on the fan shroud; next, turn clockwise.

4. To remove the filter, turn the filter or knob anti-clockwise.

5. Refit the grille, the filter or the grease filter surround.

Change the carbon filter every four months.

CONTROL PANEL

Light switch.

Speed selector switch.

Fig. 1

Fig. 2

Fig. 3

Fig. 4

PRODUCT SHEET

31833182.fm Page 7 Wednesday, November 16, 2005 4:56 PM

5019 318 33182

D F NL E

P IGR

D F NL E

P IGR

SAFEGUARDING THE ENVIRONMENT

1. Packaging

Packaging materials are 100% recyclable and are marked with the

recycling symbol .Dispose of the appliance in conformity with

local environmental regulations. Packaging materials can be

dangerous for children. Keep packaging materials (plastic bags,

polystyrene, etc.) well out of their reach.

2. Product

This appliance is marked in compliance with European Directive

2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

By ensuring that this appliance is scrapped suitably, you can help

prevent potentially damaging consequences for the environment and

health.

The symbol on the appliance or accompanying documentation

indicates that this product should not be disposed of as unsorted

municipal waste but must be taken to a collection point for the

treatment of WEEE.

Disposal must be carried out in accordance with local environmental

regulations for waste disposal.

For further information on the treatment, recovery and recycling of

this appliance, contact your competent local authority, the collection

service for household waste or the shop where you purchased the

appliance.

PRECAUTIONS AND GENERAL

RECOMMENDATIONS

WARNING!

• Do not allow children or infirm persons to operate the

appliance without supervision.

• Make sure children do not play with the appliance.

1. Do not connect the appliance to the mains electricity supply until

installation is completed. Always disconnect the hood from the

mains before performing any cleaning or maintenance.

2. Do not “flambé” food under the hood. Naked flames could

cause a fire.

3. Do not leave pans unattended when frying. Cooking oil can

catch fire.

4. Regular cleaning and maintenance is essential to correct

functioning and good performance. Regularly remove dirt

deposits. Regularly clean or replace filters. Never use flammable

materials as hoses for extracted air.

5. If the hood is used together with non-electrically powered

appliances, ambient negative pressure must not exceed 4Pa (4 x

-5

bars). Make sure the room is adequately ventilated.

Electrical connections

Before connecting the hood to the power supply, make sure the

voltage specified on the dataplate matches that in your home. The

dataplate is located inside the hood behind the grease filter.

If the appliance is fitted with a power cable and plug, the plug must

be placed in an accessible position.

If the hood does not come pre-fitted with a mains plug, fit one that

conforms to applicable standards or use a double-pole switch with a

minimum breaking gap of 3 mm.

Replacement of the power supply cable with power plug or flexible

cable may only be carried out by an authorized Service Centre or a

qualified electrician.

Cleaning the hood

Warning!

Failure to remove oil and grease at least once a month

could lead to fire.

Use a soft cloth with a neutral detergent. Never use abrasive

substances or alcohol.

Before using the hood

Please read these instructions carefully and keep them for future

reference, in order to ensure best use of your hood.

Packaging materials can be dangerous for children. Keep packaging

materials (plastic bags, polystyrene, etc.) well out of their reach.

Make sure the hood has not been damaged during transport.

Installation, electrical connections and replacement of the mains lead

with a plug or new flexible cable must be carried out by a qualified

technician in compliance with local safety regulations.

Declaration of conformity

This product has been designed, manufactured and sold in

conformity to the following standards:

- the safety standards of the "Low Voltage" Directive 73/23/EEC

- protection requirements of “EMC” Directive 89/336/EEC

amended by Directive 93/68/EEC.

Troubleshooting guide

The hood does not work:

• Is the plug properly inserted in the power socket?

• Is there a power failure?

• Is the fuse blown?

The hood is not extracting efficiently:

• Is the right speed selected?

• Do the filters need cleaning or replacing?

• Are the air outlets blocked?

The light does not work:

• Does the bulb need replacing?

• Is the bulb correctly fitted?

• Is the fuse blown?

TECHNICAL ASSISTANCE SERVICE

Before calling the Assistance Service

1. Check if you can fix the problem yourself (see ”Troubleshooting

guide”).

2. Switch the hood off and then on again to check if the problem

has gone.

3. If the problem persists, contact the Assistance Service.

Specify:

•the nature of the problem,

• the model of hood, stated on the data plate inside the hood,

accessible by removing the grease filters.

• your full address,

• your telephone number and area code.

• the service code (the number appearing below the word

SERVICE on the data plate inside the hood behind the grease

filter).

If any repairs are needed, contact an authorised Service Centre (to

ensure that only original spare parts are used and that repairs are

made correctly).

Failure to comply with these instructions may compromise the safety

and quality of the product.

31833182.fm Page 8 Wednesday, November 16, 2005 4:56 PM

Whirlpool AKR 608 IX Program Chart

Brand: Whirlpool

Model: AKR 608 IX

Category: Cooker hoods

Type: Program Chart

This manual is also suitable for

Download PDF

report

Whirlpool AKR 608 IX Program Chart

This manual is also suitable for

Whirlpool AKR 608 IX Program Chart

Related papers

Other documents