jWIN JD-VD765 Quick Start
- Category
- Portable DVD/Blu-Ray players
- Type
- Quick Start
- 1 -
Getting to Know Your Portable DVD Player
RIGHT SIDE DIAGRAM
REMOTE CONTROL DIAGRAM
Service life of battery
1. The battery normally lasts for about one year although this
depends on how often and for what operations the remote
control is used.
2. If the remote control unit fails to work even when it is
operated near the player, replace the battery.
3. Use a 3V lithium battery, No. CR2025.
BATTERY INSTALLATION FOR THE REMOTE
CONTROL
Insert the battery and match the (+) and (-) on battery to the marks
inside the battery compartment.
First-time use:
Remember to remove the insulating
Mylon piece from the battery.
1. SETUP button
2. INFO. button
3. MENU button
4. PAUSE/UP button
5. F.BWD/LEFT button
6. PLAY/SEL. button
7. PREVIOUS button
8. STOP/DOWN button
9. Number buttons
10. MODE button
Portable DVD Player
Quick Guide
Welcome to the Portable DVD Player Quick Guide.
Please carefully follow the instructions to set up your
Portable DVD Player.
FRONT VIEW DIAGRAM
1
2
3
4
5
6
7
8
18
17
16
15
14
13
12
11
10
9
19
+
+
CR2025
OPEN
PUSH
REMOTE CONTROL OPERATION RANGE
Point the remote control unit no more than 6 meters from the remote
control sensor and within 60
0
of the front of the unit.
The operating distance may vary according to the brightness of the
room.
Note:
1. Do not point bright lights at the remote control signal
sensor.
2. Do not place objects between the remote control unit and
the remote control signal sensor.
3. Do not use this remote control unit while simultaneously
operating the remote control unit of any other equipment.
Before using the battery pack, make sure to charge it.
You could choose to charge the battery pack directly or charge
it while attached to the portable DVD player.
remote sensor
11. LCD button
12. SUBTITLE button
13. TITLE button
14. ANGLE button
15. F.FWD/RIGHT button
16. AUDIO button
17. NEXT button
18. REPEAT 1/ALL button
19. MUTE button
Charge Time(hr) DVD Playback Time(hr)
NiMH 3800mAh
(6S1P)
Battery Pack Information (Charge & Playback Time)
3.5 2.7
Using the Battery Pack
“The shape of the following battery pack is only for reference; the actual
shape may differ.”
Battery release
button
Battery charge
indicator
DC IN jack
Battery
connectors
30
JDVD765QGV10M13EN07132005
JD-VD765
Remote Sensor
SPEAKERS
LCD screen
POWER indicator
OPEN button
SPEAKERS
STOP button
PAUSE button
PLAY button
1. Volume Adjustment scroll wheel
2. Headphone jack
3. Coaxial output jack
4. Audio output jack
5. Video output jack
6. POWER button
7. S-Video/P-Scan output jack
8. DC IN jack
PHONES
VOLUME
COAXIAL AUDIO
VIDEO
S-VIDEO
P-SCAN
56 8712 43
English
- 2 -
STEP 2. Connect it with earphones or connect it to external
equipment. (B)
This unit can be connected to a television or home
sound system.
Note: Before connections, be sure to turn off the power to the
JD-VD765 and to any external equipment being used.
STEP 3. Open the display panel. (C)
STEP 4. Slide the POWER switch to ON, on the portable DVD
player. (D)
STEP 5. Press <OPEN> to open the disc cover. (E)
STEP 6. Gently hold the edge of the disc, then put it on the
center hub with the printed side up.
STEP 7. Close the disc cover.
STEP 8. Press
<PLAY/SEL.> to play the disc.
(C)
(D)
(E)
Quick Operation Guide
STEP 1. Connecting to Power. (A)
Please connect the supplied AC adaptor to the DC IN
jack on the right side of the portable DVD Player.
A. To charge the battery pack directly
STEP 1. Connect the AC adapter (12V, 1.25A) to the DC IN
jack on the left side of the battery pack and a
household power outlet as shown in figure (A).
STEP 2. The battery charge indicator will turn red and start
charging.
STEP 3. When the battery pack is fully charged, the battery
charge indicator will turn green.
B. To charge the battery pack while attached to
the portable DVD player
STEP 1. Please align the portable DVD player’s battery
connectors with the battery pack’s battery
connectors. Attach the battery pack to the portable
DVD player as shown in figure (B).
Note:
1. Please turn the power off when attaching or removing the
battery pack.
2. If you want to remove the battery pack, press battery
release button, then slowly remove it from the portable
DVD player.
STEP 2. Connect the AC adapter (12V, 1.25A) to the DC IN
jack on the right side of the portable DVD player and a
household power outlet.
STEP 3. The battery charge indicator will turn red and start
charging.
STEP 4. When the battery pack is fully charged, the battery
charge indicator will turn green.
Note:
1. The battery pack is not charged while the JD-VD765 is turned
on.
2. Please use the specific power adapter (12V, 1.25A) to charge
the battery pack.
(B)
Note: Make sure the external equipment supports the audio/
video input feature. (sometimes called Line In).
1 2 3
4
(White)(Red) (Y ellow) (Blue)(Red) (Green)
Back/front panel of external equipment
P-Scan TV
Pb
Pr
Y
(Blue)
(Red)
(Green)
Video input
4
Audio input
(White)
L
R
(Red)
1
TV
Video input
2
S-Video
TV S-Video input
3
(B)
(A)
DC IN jack
(A)
VOLUME
PHONES
COAXIAL AUDIO VIDEO
S-VIDEO
P-SCAN
VOLUME
PHONES
COAXIAL AUDIO VIDEO
S-VIDEO
P-SCAN
Video
-
1
-
2
jWIN JD-VD765 Quick Start
- Category
- Portable DVD/Blu-Ray players
- Type
- Quick Start
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
