Kogan KAWLM55CNRA User guide

Brand: Kogan

Model: KAWLM55CNRA

Category: Flat panel wall mounts

Type: User guide

Kogan KAWLM55CNRA is a full motion corner wall mount, suitable for TVs with a screen size of 23" - 55". It is VESA compatible, meaning it can be used with TVs that have a VESA hole pattern of 200x100, 200x200, 300x200, 300x300, 400x200, 400x300, or 400x400. The mount has a rated weight of 45kg (99 lbs) and is made of durable materials, ensuring that it can safely support your TV.

The Kogan KAWLM55CNRA is easy to install and comes with all the necessary hardware. It has a tilt angle of -5° to +15° and a swivel angle of -90° to

TILT EXTENDABLE FULL MOTION

CORNER WALL MOUNT

(23" - 55")

KAWLM55CNRA

• Please closely follow the assembly instructions. Improper installation may result in

damage or serious personal injury.

• Safety gear and quality tools must be used.

• This product is suitable for installation on solid concrete walls, masonry walls or

wood stud walls.

• Make sure that the supporting surface will safely support the combined weight of

the equipment and all attached hardware and components.

• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting

screws.

• Do not allow children to play near this stand.

• This product contains small items that could be a choking hazard if swallowed.

Keep these items away from children.

• This product is intended for indoor use only. Using this product outdoors could lead

to product failure and personal injury.

• A minimum of two people are recommended for this installation. Failure to use

safety gear and safe working methods may result in property damage, serious

injury or death.

IMPORTANT: Ensure that you have received all parts according to the component checklist

prior to installation. If any parts are missing or faulty, contact your place of purchase for a

replacement.

MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at

least every three months).

VESA compatibility:

200x100, 200x200, 300x200, 300x300, 400x200, 400x300, 400x400

CAUTION:

Rated weight is 45kg (99 lbs).

Use with products heavier than the rated weights indicated may result

in instability causing possible injury.

Suitable for TVs 23” – 55” maximum

SAFETY & WARNINGS

Wall mount assembly:

A (x1)

B (x1)

C (x2)

D (x2)

E M6 (x3)

F (x8)

G (x1)

W-A ST6.3x55 (x8)

W-B Ø10x45 (x8)

W-C (x8)

Adapters (depends on TV):

M-A M5x14 (x4)

M-B M6x14 (x4)

M-C M6x30 (x4)

M-D M8x30 (x4)

M-E M8x50 (x4)

M-F D5 (x4)

M-G D8 (x4)

M-H (x8)

M-I (x8)

COMPONENTS

Additional Tools Required (Not Supplied):

Phillips head

screwdriver

Stud finder

Spirit level

Pencil

Electric drill

Socket wrench

Step 1: Drywall, plaster or timber walls (with studs)

Use a stud finder to locate safe and suitable locations to install into wall. Use a spirit level to

double check the correct angle of the mount and mark the intended hole positions with a

pencil. Drill holes in the desired locations (55mm deep, 4.5mm wide).

With the wall mount held in place, insert

the washers and screws (W-C, W-A),

tightening with a socket wrench. When

installing on a drywall, plaster or timber

wall, do not use the screw anchors (W-B).

ASSEMBLY

Step 1: Concrete and masonry walls

Use a spirit level to double check the correct angle of the mount and mark the intended hole

positions with a pencil. Drill holes in the desired locations (60mm deep, 10mm wide).

Insert the screw anchors (W-B) into each pre-drilled hole. With the wall mount held in place,

insert the washers and screws (W-C, W-A), tightening with a socket wrench.

For all wall types:

A minimum of two people are recommended for this installation.

Failure to use safety gear and safe working methods may result in

property damage, serious injury, or death.

Ensure washers and screws are aligned in the

centre of opening. Do not install with washers and

screws off to either side.

Step 2: Preparing the VESA mount plate

Ensure the two top nuts (E) are not fully tightened, leaving a gap of 4mm.

Configuration for VESA 300x300, 400x400:

300x200, 400x200:

400x300:

Step 3: Attaching the mounting brackets to your TV.

Depending on your TV, a combination of spacers (M-H, M-I) may be required to help create

the correct amount of space for the brackets. Ensure the screws are fitted correctly into your

TV’s VESA mount holes, and are not too long or too short in the back of the TV.

Spacers

Step 4: Attaching the TV to the wall mount.

With two people, lift the TV up and into position on the mount, ensuring the 4mm gaps on

the mount plate nuts slide into the two openings on the mount.

The lower bolt of the mount plate should feed through the opening at the bottom of the

mount. Secure this with a nut (E), while tightening the two top nuts.

A minimum of two people are recommended for this installation.

Failure to use safety gear and safe working methods may result in

property damage, serious injury, or death.

Step 5: Use the supplied cable management clips to secure all of the TV’s power and

connection cables, as shown below.

Adjusting level angle: Loosen the nuts on the back of the mount (as shown below) to

balance the TV’s level. When done, ensure nuts are securely tightened.

Adjusting tilt angle: Loosen the nuts on the side of the mount (as shown below) to adjust

the TV’s tilt angle. When done, ensure nuts are securely tightened.

ADJUSTING

NOTES

Need more information?

We hope that this user guide has given you

the assistance needed for a simple set-up.

For the most up-to-date guide for your product,

as well as any additional assistance you may require,

head online to help.kogan.com

Kogan KAWLM55CNRA User guide

Brand: Kogan

Model: KAWLM55CNRA

Category: Flat panel wall mounts

Type: User guide

The Kogan KAWLM55CNRA is easy to install and comes with all the necessary hardware. It has a tilt angle of -5° to +15° and a swivel angle of -90° to

Download PDF

report

Kogan KAWLM55CNRA User guide

Kogan KAWLM55CNRA User guide

Related papers

Other documents