Kogan KAS8C4W1TBB User guide

Brand: Kogan

Model: KAS8C4W1TBB

Type: User guide

Kogan KAS8C4W1TBB is a comprehensive 8-channel, 1080p security system with 4 wireless cameras, providing reliable surveillance for your property. Utilizing advanced Wi-Fi connectivity, the cameras transmit footage to the NVR, allowing for wire-free installation and flexible placement. With a massive 1TB hard drive, you can store weeks of continuous footage, ensuring you never miss a moment. Experience peace of mind with customizable motion detection and recording schedules, ensuring you only capture the events that matter.

8 CHANNEL 1080P 1TB

SECURITY SYSTEM

(WITH 4 WIRELESS CAMERAS)

KAS8C4W1TBB

NVR

Wi-Fi Antenna Port

WAN Port (video in)

VGA Port

HDMI Port

USB Port

Power Input (DC 12V 2A)

OVERVIEW

①

④

①

③

⑥

⑤

②

Camera

Antenna

Camera Mount

Lens & Sensors

Ethernet Port (RJ-45)

Power Input (DC 12V 2A)

①

④

③

⑤

②

System Overview

Notes:

• Camera connection to NVR is wireless: the NVR connection to the router is wired.

• It is recommended to place the NVR in the centre of the monitoring area and to

avoid obstacles between the cameras and NVR as much as possible.

Power adapter

Camera

Display device

VGA Output

NVR

Mouse

Router

Video in

USB Interface

INSTALLATION

Power

adapter

Adding Camera

The supplied cameras are matched at the factory. Re-adding or adding an additional

camera can be done in the Video Management settings on the NVR using either “auto add”

(cameras will be detected automatically) or “match code”.

Cameras’ antennas should be positioned parallel to the Wi-Fi signal transmission and not

angled directly at the router.

The cameras can also be set up with a wired network connection.

Correct

Incorrect

NVR

Router

Power

adapter

Power adapter

Power

adapter

Power

adapter

System Setup

The system is a standalone unit with an embedded Linux operating system in the NVR. To

configure the operating system, connect a keyboard, mouse and monitor with HDMI or VGA

input.

1. Install antennas for cameras and NVR.

2. Connect a monitor via HDMI or VGA.

3. Connect the NVR to power (use the larger 12V 2A power adaptor).

4. Connect the cameras to power (use the smaller 12V 1A power adaptors).

5. The camera feed will display within a few seconds.

6. Connect the included USB mouse to a USB port on the rear of the unit.

Hard Drive Replacement

• Unplug NVR, unscrew & remove top

cover.

• Remove HDD.

Connect SATA power + data cables from

NVR to new HDD.

Keep HDD in position and screw in holes

from underneath the NVR to secure it in

place.

Replace top cover.

Mouse Function

Button

Action

Effect

Function

Left

Single click

Select

Option button, drop down menu, list,

check box, radio button

Double click

Window zoom

1. Switch between single and multi-

interface in preview

2. Add device

Drag

Set the area

1. Set motion detection area

2. Select electronic amplification area

Middle

Scroll

Change the

content

1. Change contents of the drop-down

box

2. In zoom preview, switch channel

interface orderly

Right

Single click

Log out

1. Close interface

2. Show shortcut menu in main

interface

OPERATION

Right click to access the following options:

• Split screen: single/multiple camera live feed

• Video management: manage IP & NVR channels

• System setup: change system settings

• Video playback: play back recordings

• Video backup: back up recordings

• Colours adjust: adjust image settings

• PTZ control: adjust PTZ settings (on supported cameras)

• Manual record: change recording settings

• Volume: change audio settings (on supported cameras)

• Setup Wizard: step-by-step initial setup guide

• Fast network: change network settings

• Exit System: logout, reboot, close display output and shut down system

FUNCTIONS

Recording Video

• Timed Recording: Right click System Setup > Record Setup > Record Plan. You can set

a schedule to record. The default mode is 24/7.

• Manual Recording: Right click Manual Record. Individual channels can be

enabled/disabled.

• Motion Recording: Right click System Setup > Record Setup > Record Plan. Deselect

Time and select Motion; the camera will only record when it detects motion.

Playback

Right click Video Playback > Manual Search. You can search by channel and time and

click Playback to view recorded videos.

Backup

• Connect a USB drive to a USB port on the device.

• Right click Video Backup > Choose Backup Channel > Choose Video Mode > Setup

Searching Time > Search. Choose the video file to back up.

• Supported drive size is up to 32GB and supported recording is up to 1 hour.

• Right-click on the shortcut menu and click the user to log off.

• To set a logout automatically, you can set this in system > general settings. The system

will automatically log off the system in 1 minute. Username and password will need to

be re-entered when next using the system.

Restart & Shut Down

• To restart the machine during use, right-click the shortcut menu and select “exit

system”: click to complete the restart.

• To shut the machine down, right-click the shortcut menu and select the shutdown

option.

Local Viewing

With the PC and the NVR connected to the same Local Area Network (LAN),

1. Find the IP address and port number of the NVR (through System Setup >

Network Setup).

2. Enter the IP address in the browser (e.g., http://192.1.17). If the default port number

has changed from 80, enter the port number as well in the format (e.g., if the port

number was changed to 100 e.g., http://192.1.1.100)

Remote Viewing

1. Navigate to http://e-seenet.com in a browser.

2. Input Device ID, username and password to log in.

Device ID is shown at the right bottom corner of the monitor. The status should show as

“online”. The default username is admin and the default password is empty.

Mobile Access

1. Download the IP PRO app from the App Store, Play Store or by scanning the QR

code below.

o Add the NVE through the device ID, username and password.

o Device ID is shown at the right bottom corner of the monitor. The status

should show as “online”. The default username is admin and the default

password is empty.

o Live playback is supported within the app. Due to network conditions and

connection speed, playback over LAN will be more reliable and consistent

than playback from mobile data.

A wireless network is inherently susceptible to range limitations and interference from

obstacles, etc. To improve the reliability and stability of a Wi-Fi connection, refer to the

following setup tips and configuration options.

Antenna Extension

Repeater Setup

In the repeater setup page, first set up and connect any IP Camera to the NVR. This

function increases the wireless transmission distance and extends the total range of

wireless kit.

1. Right click and select Video Management > Repeater.

2. Add repeater: as below, click the icon and a channel besides the currently one

being copied from (channel 3 in this example).

EXTENDING WIFI RANGE

Antenna Extension Cord

IP Camera

Wall

Window

NVR

3. As below, IPC1 is connected to the NVR through IPC2 and IPC3. IPC2 is connected

to NVR through IPC3. IPC3 is connected to NVR directly.

4. Click Apply > Refresh to confirm the setup is successful.

NOTES

Need more information?

We hope that this user guide has given you

the assistance needed for a simple set-up.

For the most up-to-date guide for your product,

as well as any additional assistance you may require,

head online to help.kogan.com

Kogan KAS8C4W1TBB User guide

Kogan KAS8C4W1TBB User guide

Kogan KAS8C4W1TBB User guide

Other documents