Makita 6402 DP4700 User manual

GB

Drill Instruction Manual

F

Perceuse Manuel d’Instructions

D

Bohrmaschine Betriebsanleitung

I

Trapano Istruzioni d’Uso

NL

Boormachine Gebruiksaanwijzing

E

Taladro Manual de Instrucciones

P

Berbequim Manual de Instruço˜es

DK

Boremaskine Brugsanvisning

S

Borrmaskin Bruksanvisning

N

Boremaskin Bruksanvisning

SF

Porakone Käyttöohje

GR

∆Ú˘¿ÓÈ √‰ËÁ›Â˜ ÃÚ‹ÛÂˆ˜

10 mm 6402

13 mm DP4700

6402

DP4700

DP4700/6402 (cover) (’96. 5. 11)

Page is loading ...

ENGLISH

Explanation of general view

1 Side grip

2 Tighten

3 Chuck key

4 Sleeve

5 Ring

6 High

7 Low

8 Speed control screw

9 Switch trigger

0 Lock button

q Reversing switch lever

w Reversing switch lever

SPECIFICATIONS

Model 6402 DP4700

Capacities

Steel ......................................................................................................... 10 mm 13 mm

Wood ....................................................................................................... 21 mm 36 mm

No load speed (RPM) ................................................................................ 0 – 1,200 0 – 550

Overall length ............................................................................................. 264 mm 275 mm

Net weight .................................................................................................. 1.7 kg 2.0 kg

•

Due to the continuing program of research and

development, the specifications herein are subject

to change without prior notice.

•

Note: Specifications may differ from country to

country.

Power supply

The machine should be connected only to a power

supply of the same voltage as indicated on the

nameplate, andcan only be operated on single-phase

AC supply. They are double-insulated in accordance

with European Standard and can, therefore, also be

used from sockets without earth wire.

Safety hints

For your own safety, please refer to enclosed safety

instructions.

These symbols mean:

Read instruction manual.

DOUBLE INSULATION

ADDITIONAL SAFETY RULES

1. Always be sure you have a firm footing. Be

sure no one is below when using the machine

in high locations.

2. Hold the machine firmly.

3. Keep hands away from rotating parts.

4. When drilling into walls, floors or wherever

‘‘live’’electrical wires may be encountered, DO

NOT TOUCH ANY METAL PARTS OF THE

MACHINE! Hold the machine by the insulated

grasping surfaces to prevent electric shock if

you drill into a ‘‘live’’ wire.

5. Do not leave the machine running. Operate the

machine only when hand-held.

6. Do not touch the drill bit or the workpiece

immediately after operation; they may be

extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing side grip (auxiliary handle) (Fig. 1)

For DP4700 only

Screw the side grip on the machine securely.

Installing or removing drill bit

Important:

Always be sure that the machine is switched off and

unplugged before installing or removing the bit.

For machines with standard keyed chuck (Fig. 2)

To install the bit, place it in the chuck as far as it will

go. Tighten the chuck by hand. Place the chuck key in

each of the three holes and tighten clockwise. Be sure

to tighten all three chuck holes evenly. To remove the

bit, turn the chuck key counterclockwise in just one

hole, then loosen the chuck by hand.

After using the chuck key, be sure to return it to the

original position.

For machines with keyless chuck (Fig. 3)

Hold the ring and turn the sleeve counterciockwise to

open the chuck jaws. Place the bit in the chuck as far

as it will go. Hold the ring firmly and turn the sleeve

clockwise to tighten the chuck. To remove the bit, hold

the ring and turn the sleeve counterclockwise.

Switch action (Fig. 4)

CAUTION:

Before plugging in the machine, always check to see

that the switch trigger actuates properly and returns to

the ‘‘OFF’’ position when released.

To start the machine, simply pull the trigger. Machine

speed is increased by increasing pressure on the

trigger. Release the trigger to stop. For continuous

operation, pull the trigger and then push in the lock

button. To stop the machine from the locked position,

pull the trigger fully, then release it. A speed control

screw is provided so that maximum machine speed

can be limited (variable). Turn the speed control

screw clockwise for higher speed, and counterclock-

wise for lower speed.

DP4700/6402 (Eng) (’96. 5. 11)

3

Reversing switch action

(Fig. 5 for DP4700 & Fig. 6 for 6402)

CAUTION:

•

Always check the direction of rotation before drilling.

•

Use the reversing switch only after the machine

comes to a complete stop. Changing the direction of

rotation before the machine stops may damage the

machine.

This machine has a reversing switch to change the

direction of rotation. Move the reversing switch lever

to the

position (DP4700)/the ‘‘FWD’’ position

(6402) for clockwise rotation or the

position

(DP4700) /the ‘‘REV’’ position (6402) for counter-

clockwise rotation.

Drilling operation

•

Drilling in wood

When drilling in wood, the best results are obtained

with wood drills equipped with a guide screw. The

guide screw makes drilling easier by pulling the bit

into the workpiece.

•

Drilling in metal

To prevent the bit from slipping when starting a hole,

make an indentation with a center-punch and ham-

mer at the point to be drilled. Place the point of the

bit in the indentation and start drilling.

Use a cutting lubricant when drilling metals. The

exceptions are iron and brass which should be

drilled dry.

CAUTION:

•

Pressing excessively on the machine will not speed

up the drilling. In fact, this excessive pressure will

only serve to damage the tip of your bit, decrease

the machine performance and shorten the service

life of the machine.

•

There is a tremendous force exerted on the

machine/bit at the time of hole breakthrough. Hold

the machine firmly and exert care when the bit

begins to break through the workpiece.

•

A stuck bit can be removed simply by setting the

reversing switch to reverse rotation in order to back

out. However, the machine may back out abruptly if

you do not hold it firmly.

•

Always secure small workpieces in a vise or similar

hold-down device.

MAINTENANCE

CAUTION:

Always be sure that the machine is switched off and

unplugged before carrying out any work on the

machine.

To maintain product safety and reliability, repairs,

maintenance or adjustment should be carried out by

Makita Authorized Service Center.

GUARANTEE

We guarantee Makita machines in accordance with

statutory/country-specific regulations. Damage attrib-

utable to normal wear and tear, overload or improper

handling will be excluded from the guarantee. In case

of complaint, please send the machine, undismantled,

with the enclosed GUARANTEE CERTIFICATE, to

your dealer or the Makita Service Center.

4

DP4700/6402 (Eng) (’96. 5. 15)

Page is loading ...

DP4700/6402 (back) (’97. 4. 7)

31

Makita Corporation

Anjo, Aichi, Japan

Made in Japan

883255C947

Makita 6402 DP4700 User manual

Makita 6402 DP4700 User manual

in other languages

Related papers

Other documents