Renesas M30240T-RPD-E User manual

Brand: Renesas

Model: M30240T-RPD-E

Type: User manual

This manual is also suitable for

PCA7302E1F-80

M30240T-RPD-E

Emulation Pod for M30240 Group MCUs

User's Manual

Rev.1.00

September 1, 2003

REJ10J0262-0100Z

( 2 / 58 )

• IC61-080-079, IC61-080-081 and IC61-0804-046 are products of Yamaichi Electronics Co., Ltd.

Keep safety first in your circuit designs!

• Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products better

and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal

injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate

measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any

malfunction or mishap.

Notes regarding these materials

• These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited to

the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas

Technology Corporation, Renesas Solutions Corporation or a third party.

• Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, or infringement of any

third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples

contained in these materials.

• All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information

on products at the time of publication of these materials, and are subject to change by Renesas Technology Corporation and Renesas

Solutions Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact

Renesas Technology Corporation, Renesas Solutions Corporation or an authorized Renesas Technology product distributor for the latest

product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or

typographical errors. Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage,

liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology

Corporation and Renesas Solutions Corporation by various means, including the Renesas home page (http://www.renesas.com).

• When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms,

please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and

products. Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, liability or

other loss resulting from the information contained herein.

• Renesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under circumstances

in which human life is potentially at stake. Please contact Renesas Technology Corporation, Renesas Solutions Corporation or an

authorized Renesas Technology product distributor when considering the use of a product contained herein for any specific purposes,

such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.

• The prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or reproduce

in whole or in part these materials.

• If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the

Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to

the export control laws and regulations of Japan and/or the country of destination is prohibited.

• Please contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the products

contained therein.

Precautions to be taken when using this product

• This product is a development supporting unit for use in your program development and evaluation stages. In mass-producing your

program you have finished developing, be sure to make a judgment on your own risk that it can be put to practical use by performing

integration test, evaluation, or some experiment else.

• In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product.

• Renesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge.

However, this does not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any

circumstances.

• This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, it does not fall

under the application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when used in

Japan.

• Do not attempt to modify this equipment. If modified, your authority to operate this equipment might be voided by FCC.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be

required to take adequate measures.

For inquiries about the contents of this document or product, fill in the text file the installer of the emulator debugger generates in the

following directory and email to your local distributor.

\SUPPORT\Product-name\SUPPORT.TXT

Renesas Tools Homepage http://www.renesas.com/en/tools

( 3 / 58 )

Preface

The M30240T-RPD-E is an emulation pod for the M30240 Group of 16-bit microcomputers. It's used

with a PC4701 emulator.

This user's manual mainly describes specifications of the M30240T-RPD-E emulation pod and how

to setup it. For details on the following products, which are used with M30240T-RPD-E, refer to each

product's user's manual.

• Emulator: PC4701M/PC4701HS/PC4701L User's Manual

• Emulator debugger: M3T-PD30 User's Manual

All the components of this product are shown in "2.2 Package Components" (page 17) of this user's

manual. If there is any question or doubt about this product, contact your local distributor.

To use the product properly

Precautions for Safety

• In both this User's Manual and on the product itself, several icons are used to insure

proper handling of this product and also to prevent injuries to you or other persons,

or damage to your properties.

• The icons' graphic images and meanings are given in "Chapter 1. Precautions for

Safety". Be sure to read this chapter before using the product.

When using outside Japan

• When using in Europe, the United States, or Canada, be sure to use both the emulator

(PC4701M, PC4701HS or PC4701L) and the emulation pod which meet overseas

standards. EMI standards are not met when the M30240T-RPD-E is used with the

PC4700H or PC4700L emulator.

( 4 / 58 )

Contents

Chapter 1. Precautions for Safety ...........................................................................................7

1.1 Safety Symbols and Meanings ..............................................................................8

Chapter 2. Preparation ..........................................................................................................15

2.1 Terminology ........................................................................................................16

2.2 Package Components ..........................................................................................17

2.3 Other Tool Products Required for Development ................................................17

2.4 Name of Each Part ..............................................................................................18

(1) System Configuration...............................................................................18

(2) Inside of Emulation Pod...........................................................................19

2.5 When Using the Emulator for the First Time......................................................20

Chapter 3. Setting Up ...........................................................................................................21

3.1 Removing the Upper Cover ................................................................................22

3.2 Switch Settings....................................................................................................23

3.3 Selecting Clock Supply .......................................................................................25

(1) Using the Oscillator Circuit on the Target System ..................................26

(2) Changing the Internal Oscillator Circuit of Emulation Pod.....................27

(3) Replacing the Oscillator Circuit Boards ..................................................28

3.4 A-D Conversion Bypass Capacitor .....................................................................29

3.5 Connecting the PC4701 and Emulation Pod .......................................................30

(1) Connecting the Cable to the PC4701 .......................................................30

(2) Connecting the Cable to the Emulation Pod ............................................31

3.6 Connecting the Target System ............................................................................32

(1) How to Connect the Target System .........................................................32

(2) Connecting 80-pin LCC Socket ...............................................................33

3.7 Modifying the MCU File for M3T-PD30 ...........................................................34

Chapter 4. Usage ..................................................................................................................35

4.1 Turning On the Power .........................................................................................36

(1) Checking the Connection of the Emulator System ..................................36

(2) Turning On the Power ..............................................................................36

(3) LED Display When PC4701 Starts Up Normally....................................37

4.2 Downloading Firmware ......................................................................................38

(1) When It is Necessary to Download Firmware .........................................38

(2) Downloading Firmware in the Maintenance Mode .................................38

4.3 Self-checks ..........................................................................................................39

(1) Self-check Procedure ...............................................................................39

(2) If an Error is Detected in Self-checks ......................................................39

( 5 / 58 )

Chapter 5. Specifications......................................................................................................41

5.1 Specifications ......................................................................................................42

5.2 Connection Diagram ...........................................................................................43

(1) Connection Diagram of M30240T-RPD-E ..............................................43

5.3 External Dimensions ...........................................................................................44

(1) External Dimensions of Emulation Pod ...................................................44

(2) External Dimensions of Pitch Converter Board (FLX-80LCC) ..............45

Chapter 6. Troubleshooting ..................................................................................................47

6.1 Flowchart to Remedy the Troubles .....................................................................48

6.2 When the Emulator Debugger Does Not Start Up Properly ...............................49

(1) When the LED Display of PC4701 is Abnormal .....................................49

(2) Errors Occur When the Emulator Debugger Starts Up

(When the target system is connected)....................................50

(3) Errors Occur When the Emulator Debugger Starts Up

(When the target system is not connected) .............................51

6.3 Operation Differs from That of Actual MCUs....................................................51

Chapter 7. Maintenance and Guarantee................................................................................53

7.1 Maintenance ........................................................................................................54

7.2 Guarantee ............................................................................................................54

7.3 Repair Provisions ................................................................................................54

7.4 How to Request for Repair..................................................................................55

( 6 / 58 )

MEMO

( 7 / 58 )

Chapter 1. Precautions for Safety

This chapter describes precautions for using this product safely and properly. For precautions for the emulator main unit

and the emulator debugger, refer to each user's manual included with your product.

1.1 Safety Symbols and Meanings .....................................................................................................8

Warning for Installation...............................................................................................9

Warnings for Use Environment ...................................................................................9

Caution to Be Taken for Modifying This Product .......................................................9

Cautions to Be Taken for This Product........................................................................9

Note on Malfunctions in the PC4701 System..............................................................9

Notes on Downloading Firmware..............................................................................10

Notes on Target System .............................................................................................10

Note on Reset Input from the Target System.............................................................10

Notes on Watchdog Function.....................................................................................10

Note on When the Emulator Debugger Ends.............................................................10

Notes on Stack Area...................................................................................................11

Note on Address 0 Access .........................................................................................11

Note on Changing the Settings of Memory Area.......................................................11

Note on BRK Instruction ...........................................................................................11

Notes on S/W Beaks ..................................................................................................11

Note on S/W Breaks and H/W Breaks.......................................................................11

Notes on Address Match Interrupt.............................................................................12

Note on Software Reset .............................................................................................12

Note on Stop and Wait Modes ...................................................................................12

Note on Differences between Actual MCU and Emulator ........................................13

Note on Referencing and Setting the Work Area ......................................................13

Notes on MAP References and Settings ....................................................................13

CAUTION

WARNING

IMPORTANT

( 8 / 58 )

Chapter 1. Precautions for Safety

In both the user's manual and on the product itself, several icons are used to insure proper handling

of this product and also to prevent injuries to you or other persons, or damage to your properties.

This chapter describes the precautions which should be taken in order to use this product safely and

properly. Be sure to read this chapter before using this product.

1.1 Safety Symbols and Meanings

The following pages describe the symbols "WARNING", "CAUTION", and "IMPORTANT".

In addition to the three above, the following are also used as appropriate.

means WARNING or CAUTION.

Example: CAUTION AGAINST AN ELECTRIC SHOCK

means PROHIBITION.

Example: DISASSEMBLY PROHIBITED

means A FORCIBLE ACTION.

Example:

UNPLUG THE POWER CABLE FROM THE RECEPTACLE.

If the requirements shown in the "WARNING"

sentences are ignored, the equipment may

cause serious personal injury or death.

If the requirements shown in the "CAUTION"

sentences are ignored, the equipment may

malfunction.

It means important information on using this

product.

WARNING

IMPORTANT

CAUTION

( 9 / 58 )

IMPORTANT

Note on Malfunctions in the PC4701 System

• If the emulator malfunctions because of interference like external noise, do the following to remedy

the trouble.

(1) Press the RESET switch on the emulator front panel.

(2) If normal operation is not restored after step (1), shut OFF power to the emulator once and then

reactivate it.

WARNING

Warning for Installation:

• Do not set this product in water or areas of high humidity. Spilling water or some other liquid into

the main unit can cause an unrepairable damage.

Warnings for Use Environment:

• The emulation pod is air-cooled with the ventilation slot. Therefore, do not block the ventilation

slot. When heated to high temperatures, the emulation pod may not work properly.

• This equipment is to be used in an environment with a maximum ambient temperature of 35°C. Care

should be taken that this temperature is not exceeded.

CAUTION

Caution to Be Taken for Modifying This Product:

• Do not disassemble or modify this product. Disassembling or modifying this product can cause

damage. Disassembling and modifying the product will void your warranty.

Cautions to Be Taken for This Product:

• Use caution when handling the main unit. Be careful not to apply a mechanical shock.

• Do not touch the connector pins of the emulator main unit and the target MCU connector pins . Static

electricity may damage the internal circuits.

• Do not pull the emulation pod main unit by the flexible cable (FLX120-RPD) for connecting to the

emulator main unit or the flexible cable (FLX64, FLX100 or FLX160) for connecting the target

system. The cable may cause a break.

• Flexible cable (FLX120-RPD) for connecting to the emulator main unit and the flexible cable

(FLX64, FLX100 or FLX160) for connecting the target system are different from earlier models.

The slits make them more flexible. However, excessive flexing or force may break conductors.

•Do not use inch-size screws for this equipment. The screws used in this equipment are all ISO

(meter-size) type screws. When replacing screws, use same type screws as equipped before.

( 10 / 58 )

IMPORTANT

Notes on Downloading Firmware:

• Before using this product for the first time, it is necessary to download the dedicated firmware

(control software for the emulation pod built into the PC4701). Please note that, to do this, it is

necessary to start up the PC4701 in the maintenance mode. For firmware download procedures, see

"4.2 Downloading Firmware" (page 38). Once the firmware has been downloaded, the product can

be used by simply turning on the power.

• Do not shut off the power while downloading the firmware. If this happens, the product will not

start up properly. If power is shut off unexpectedly, redownload the firmware.

• Except when a target status error occurs, if self-checks are not completed successfully, there may

be trouble with the product. In such case, contact your sales representative. However, perform self-

checks in the below setup.

(1) Target system: Not connected

(2) Emulation pod internal switches: At their factory-settings

Notes on Target System:

• The Vcc pin of emulator is connected to the target system to observe the voltage of the target system.

Therefore design your system so that the emulator MCU is powered by the target system.

•The voltage of the target system should be within the range of +4.75 to +5.25V.

•Do not change the voltage of the target system after turning on the power.

• Before powering on your emulator system, check that the host machine, the emulator main unit,

the converter board and target system are all connected correctly. Next, turn on the power to each

equipment following the procedure below.

(1) Turn ON/OFF the target system and the PC4701 emulator as simultaneously as possible.

(2) When the PC4701 and emulator debugger start up, check the target status LEDs on the

emulator main unit's front panel to see if this product is ready to operate.

• Is the power supplied? Check that target status LED (POWER) is ON.

• Is the RESET released? Check that target status LED (RESET) is OFF.

Note on Reset Input from the Target System:

• The reset input from the target system is accepted only while a user program is being executed (only

while the RUN status LED on the PC4701's front panel is lit).

Note on When the Emulator Debugger Ends:

• To restart the emulator debugger after it ends, always shut power to the emulator module off once

and then on again.

Notes on Watchdog Function:

• The MCU's watchdog timer can be used only while programs are being executed. To use it

otherwise, disable the timer.

• If the reset circuit of the target system has a watchdog timer, disable it when using the emulator.

( 11 / 58 )

IMPORTANT

Notes on Stack Area:

• With this product, a maximum 8 bytes of the user stack is consumed as a work area.

• If the user stack does not have enough area, do not use areas which cannot be used as stack (SFR

area, RAM area which stores data, or ROM area) as work area. Using areas like this is a cause of

user program crashes and destabilized emulator control. Therefore, ensure the +8 bytes maximum

capacity used by the user program as the user stack area.

Note on Address 0 Access:

•With the M16C/20 Series MCUs, when a maskable interrupt is generated, the interrupt data

(interrupt No. and interrupt request level) stored in address 0 is read out. Also, the interrupt request

bit is cleared when address 0 is read out. Consequently, when the address 0 readout instruction is

executed or when address 0 is read out in the cause of a program runaway, a malfunction occurs

in that the interrupt is not executed despite the interrupt request, because the request bit of the

highest priority interrupt factor enabled is cleared.

For this malfunction, when the reading out to the 0 address is generated excluding the interrupt, the

yellow LED lights up to alarm. When this LED lights, there is a possibility of wrong access,

therefore check the program. This LED is turned off by the RESET switch of the emulator main

unit.

Note on Changing the Settings of Memory Area:

• When debugging the MCU whose memory capacity is different, be sure to change the setting of

memory area. For the memory map of each MCU, refer to the user's manual of MCU.

Notes on S/W Breaks:

• S/W breaks generate BRK interrupts by substituting the proper instruction to the BRK instruction

"00h". Therefore, when referencing the result of a trace in bus mode, "00h" is displayed for the

instruction fetch address where a software break is set.

• In the area where the MAP setting is EXTERNAL, S/W breaks cannot be used.

Note on BRK Instruction:

• BRK instruction cannot be used.

Note on S/W Breaks and H/W Breaks:

• It is not possible to use a S/W break and a H/W break at the same time. If doing so, it may not operate

normally.

( 12 / 58 )

IMPORTANT

Notes on Address Match Interrupt:

• Do not set software breaks at the same addresses as address-match interrupts as the program may

run out of control.

• Do not set a hardware break within 4 instructions before an address at which an address-match

interrupt occurs. If you do set a hardware break in this range, the program will run out of control.

•When an address at which an address-match interrupt occurs is executed in one-step mode, the

program stops after executing the first instruction after returning from the address-match interrupt

processing.

Note on Software Reset:

• If using a software reset, it is possible to set only when the program is being executed. When setting

the software reset otherwise, it may not work properly.

Note on Stop and Wait Modes:

•Do not perform step execution at addresses in the stop or wait mode. It may cause communication

errors.

( 13 / 58 )

IMPORTANT

Note on Differences between Actual MCU and Emulator:

•Operations of the emulator differs from those of actual MCUs as listed below.

(1) Data values of internal resources of MCU at power-on

(2) Internal memories (RAM and ROM) capacities etc.

(3) Oscillator circuit

•Make note of the fact that in the oscillator circuit where a resonator is connected between

the XIN and XOUT pins, oscillation does not occur because a flexible cable, buffer IC and other

devices are used between the evaluation MCU and the target system.

•Make note of the fact that if the internal oscillator circuit of the emulator is selected when

the MCU is stopping, the oscillation does not stop.

(4) DBC, single-step and BRK instruction interrupt vector table addresses

As the emulator uses the DBC, single-step and BRK instruction interrupt vector table addresses,

when reading these addresses, the downloaded addresses cannot be read (see Table 1.1).

Table 1.1 Vector table addresses for the emulator

Note on Referencing and Setting the Work Area:

• The work area when starting up the emulator debugger is shown below (set the work area by "F/W and

Work Area" tab of INIT dialog). When using the emulation pod M30240T-RPD-E for the M30240

Group MCUs, use the initial value.

02C0016 to 02C0916: work area

*1 Interruption for the debugger only

(5) A-D conversion

As a flexible cable, a pitch converter board and other devices are used between the evaluation

MCU and the target system, some characteristics are slightly different from those of the actual

MCU. Therefore, be sure to evaluate your system with an evaluation MCU. Before starting

mask production, evaluate your system and make final confirmation with an ES (Engineering

Sample) version MCU.

Factor of interruption

DBC*

Single-step*

BRK instruction

Vector table address

FFFF4

16 to FFFF716

FFFEC16 to FFFEF16

FFFE416 to FFFE716

Remarks

Forbidden to use usually

Cannot be used as variable vector

Notes on MAP References and Settings:

• The map setting when starting up the M30240T-RPD-E is as follows.

0000016 to 003FF16: EXT

0040016 to FFFFF16:INT

•Be sure to set the SFR area to EXTERNAL (external).

( 14 / 58 )

MEMO

( 15 / 58 )

Chapter 2. Preparation

This chapter describes the package components, the system configuration and the preparation for using this product for the

first time.

2.1 Terminology ...............................................................................................................................16

2.2 Package Components..................................................................................................................17

2.3 Other Tool Products Required for Development........................................................................17

2.4 Name of Each Part......................................................................................................................18

(1) System Configuration ...........................................................................................................18

(2) Inside of Emulation Pod .......................................................................................................19

2.5 When Using the Emulator for the First Time.............................................................................20

( 16 / 58 )

Chapter 2. Preparation

2.1 Terminology

Some specific words used in this user's manual are defined as follows:

Emulator system

This means an emulator system built around the PC4701 emulator. The PC4701 emulator system is

configured with an emulator main unit, emulation pod, host machine and emulator debugger.

Emulator main unit (Hereafter PC4701)

This means a generic name for PC4701M, PC4701HS and PC4701L emulators for 8 and 16-bit

MCUs.

Emulation pod

This means M30240T-RPD-E (this product). This emulation pod is for the M30240 Group MCUs.

Host machine

This means a personal computer used to control the emulator and emulation pod.

Emulator debugger

This means a software tool M3T-PD30 (Ver.4.00 or greater) to control the emulator from the host

machine through an interface.

Firmware

Program that analyzes contents of communication with the emulator debugger and controls the

emulator hardware. This program is installed in the EEPROM. This program is downloadable from

the emulator debugger to upgrade the firmware or to support other MCUs.

Evaluation MCU

This means the microcomputer mounted on the emulation pod which is operated in the specific mode

for tools.

Target MCU

This means the microcomputer you are going to debug.

Target system

This means a user's application system using the microcomputer to be debugged.

In this user's manual, this symbol is used to show active LOW (e.g. RESET*: Reset signal).

( 17 / 58 )

2.2 Package Components

The M30240T-RPD-E package consists of the following items. When unpacking, check to see if your

package contains all of these items.

Please keep the M30240T-RPD-E’s packing box and cushion material in your place for reuse at a later

time when sending your product for repair or other purposes. Always use these packing box and

cushion material when transporting this product.

If any of these items are missing or found faulty, please contact your local distributor. Also, if there

is any question or doubt about the packaged product, contact your local distributor.

2.3 Other Tool Products Required for Development

To bring forward programs development on the M30240 Group MCUs, the products listed below are

necessary in addition to those contained package above. Get them separately.

To purchase these products, contact your nearest distributer.

Item

M30240T-RPD-E emulation pod main unit

FLX120-RPD flexible cable for connecting PC4701

FLX-80LCC pitch converter board for 80-pin 0.8mm-pitch LCC

OSC-2 (12MHz) oscillator circuit board (pre-installed in emulation pod)

OSC-2 oscillator circuit board (bare-board, connector pins mounted)

Hardware tool user registration FAX sheet (English)

Hardware tool user registration FAX sheet (Japanese)

M30240T-RPD-E user's manual (this manual)

M30240T-RPD-E user's manual (Japanese)

Quantity

Emulator main unit

Emulator debugger

PROM programming adapter

PC4701M, PC4701HS or PC4701L

M3T-PD30 (Ver.4.00 or greater)

PCA7302E1F-80 for 80-pin QFP

(necessary to write into MCUs with internal PROM)

PCA7302E1L-80 for 80-pin LCC

(necessary to write into MCUs with internal PROM)

( 18 / 58 )

2.4 Name of Each Part

(1) System Configuration

Figure 2.1 System configuration

(1) to (4) in Figure 2.1 are included with this product package.

(1) Emulation pod (M30240T-RPD-E)

This emulation pod contains an evaluation MCU, emulation memory and circuit to feature the

debugging functions.

(2) Flexible cable (FLX120-RPD)

This is a 120-pin flexible cable for connecting the PC4701 emulator and the emulation pod.

(3) Flexible cable (FLX100)

This is a 100-pin flexible cable for connecting the emulation pod and the target system.

(4) Pitch converter board (FLX-80LCC)

This is a pitch converter board for connecting to the target system. For details, refer to "3.6

Connecting the Target System" (page 32).

( 19 / 58 )

(2) Inside of Emulation Pod

Figure 2.2 Internal view of emulation pod

Here following explains each board in Figure 2.2.

(1) Common board (M30200T-RPDC REV.B)

This board is common for the M16C Family that control the interface for the PC4701 and the

memory.

(2) Multiplex separation board (M30240T-PRT REV.A)

Board to control the separation of the address/data output from the MCU.

(3) MCU board (M30240T-RPDM REV.A)

Board on which the MCU is mounted.

(4) Memory board (M30200T-MEM REV.A)

Board on which the 1MB of emulation memory is mounted.

( 20 / 58 )

2.5 When Using the Emulator for the First Time

If you have purchased this emulation pod newly, it is necessary to download the firmware. The

download procedure is given in Figure 2.3.

Before attempting to download the firmware, check the emulator debugger is installed and the

emulator is connected to the host machine. For more information, see each user's manual of the

emulator debugger and the PC4701.

Figure 2.3 Firmware download procedure when emulator is used for the first time

To make sure the emulation pod works properly, run the self-checks. For self-check procedures, see

"4.3 Self-checks" (page 39).

Connect the PC4701 and this product.

Within 2 seconds of turning the power ON, press the

RESET switch of the PC4701 and check the maintenance

mode is accessed.

Download the firmware using the emulator debugger.

Shut the power of the PC4701 OFF.

See "4.2 Downloading Firmware"

(page 38).

See "3.5 Connecting the PC4701

and Emulation Pod" (page 30).

Page is loading ...

Renesas M30240T-RPD-E User manual

Brand: Renesas

Model: M30240T-RPD-E

Type: User manual

This manual is also suitable for

PCA7302E1F-80

Download PDF

report

Renesas M30240T-RPD-E User manual

This manual is also suitable for

Renesas M30240T-RPD-E User manual

Related papers

Other documents