ESAB Firepower Welding/Cutting Cart Troubleshooting instruction

Firepower welding/ cutting cart instructions

0-5373, Rev. AB 1 June, 2015

!

WARNING

Maximum Load Bearing Capacity (including Cylinder) not to exceed 125lbs. (57kg).

Maximum Gas Cylinder Weight: 55lbs. (25kg).

Power Source MUST be mounted onto base box before mounting wirefeeder to handle assembly.

Accommodates up to 9" Diameter with Included Chain

!

WARNING

SAFETY FIRST! FOR YOUR OWN PROTECTION READ, UNDERSTAND AND OBSERVE THESE SAFETY

TIPS AND ALL INSTRUCTIONS BEFORE USING THIS PRODUCT!

Do not use MIG Cart for the purpose it is not intended for. Keep visitors away. All visitors should be

kept away from work area. Do not let visitors operate MIG Cart. Childproof the MIG Cart and work area.

When not in use, the MIG Cart should be stored in locked-up place.

Always wear appropriate protective clothing and equipment. Do not wear loose clothing or jewelry.

They can be caught in moving parts.

Stay alert. Watch what you are doing. Use common sense. Do not operate when you are tired or under the

inﬂuence of any medications. Be alert at all times, especially. during repetitive, monotonous operations.

Do not over-reach. Keep proper footing and balance at all times.

Before using, make sure all fasteners are tight and unit is assembled as per the attached instructions.

Carefully check for any damaged parts before use to determine that the MIG Cart will operate properly

and perform its intended function. Check for alignment of moving parts, binding of moving parts,

breakage of parts, mounting, and any other conditions that may affect its operation. Any part that is

damaged should be properly repaired or replaced by an authorized service center.

Maintain MIG Cart with care. Do not attempt to repair or disassemble the equipment while the MIG

Cart is in use. Do not alter or modify any part of this equipment. Inspect MIG Cart periodically and if

the MIG Cart or any of its parts are damaged - have it repaired by an authorized service facility. Always

keep your MIG Cart Inspected and replace immediately, if damaged or worn. MIG Cart must only be

repaired by qualiﬁed technicians.

Always chain the Compressed Gas Cylinder securely with the chain provided. Never weld to the Com

-

pressed Gas Cylinder or the MIG Cart.

Manual 0-5373

Firepower Welding/ Cutting Cart

Part Number: 1444-0407

Assembly Instructions

Instructions d'assemblage

Instrucciones de Montaje

Firepower

Suite 300, 16052 Swingley Ridge Road,

St. Louis, MO 63017, USA

Technical Service: 1-800-426-1888 FAX: 1-800-535-0557

Customer Service: 1-800-858-4232

FirepowerOnline.com

Firepower welding/ cutting cart instructions

June, 2015 2 0-5373, Rev. AB

Always use MIG Cart on level surface. Never park the MIG Cart on an inclined surface. It may roll away

and tip, causing damage. Compressed Gas Cylinder is extremely dangerous if it tips over.

Always move the MIG Cart by pushing or pulling on the MIG Cart. Never pull the MIG Cart around by

the torch or work leads since the MIG Cart might trip. Never use handle extensions to increase leverage.

Failure to heed these Warnings may result in personal fatal injury or property damage.

Keep these Warnings intact and in readable condition. A new copy may be obtained from the manu

-

facturer.

General Information

The Firepower Welding/ Cutting Cart is designed to handle most Cutters and Welders (MST220i does not ﬁt with

this cart). The sturdy and durable construction allows easy transport for the power source, wire feeder, cylinders

and various accessories. These instructions will guide you through the proper assembly procedure of the cart.

Recommended Tools

• HexWrench,6mm

• HexKey,4mm

Art # A-12871

Firepower welding/ cutting cart instructions

0-5373, Rev. AB 3 June, 2015

Supplied Parts

The following components are included in this kit:

Parts List Component List

Item Description Qty. Item Description Qty.

[A] Bottom Shelf 1 pc. [S] Bolt, 6 mm x 10 mm 31 pcs.

[B] Vertical Support 1 pc. [T] Bolt, 6 mm x 13 mm 4 pcs.

[C] Top Shelf 1 pc. [U] Bolt, 6 mm x 20 mm 4 pcs.

[D] Center Shelf 1 pc. [V] Lock Nut -6 mm 35 pcs.

[E] Side Support Rails 2 pcs. [W] Hex Nut - 6 mm 4 pcs.

[F] Handle 1 pc. [X] Flat Washer - 6 mm 8 pcs.

[G] Axle 1 pc. [Y] Spring Washer - 6 mm 35 pcs.

[H] Castor Wheels 2 pcs. [Z] Flat Washer -12 mm 4 pcs.

[I] Wheels 2 pcs.

[K] ROLL PINS 2 pcs.

[M] Chains 2 pcs

[N] Gun/Leads Hanger 2 pcs

-

Hex Wrench (6 mm) 1 pc.

-

Hex key (4 mm) 1 pc.

F

C

B

M

A

K

H

E

D

N

G

I

Art # A-12872

Firepower welding/ cutting cart instructions

June, 2015 4 0-5373, Rev. AB

Assembly Procedure

Step 1`

(1) Assemble two Castor Wheels (H) to the Bottom Shelf (A) using 4 Bolts, 6 mm x 10 mm (S), Lock

Washers (Y) and lock Nuts (V)

(2) Slide Axle (G) through support tube on bottom of the Shelf (A). Insert Flat Washers (Z) on each end of

the Axle

(3) Insert Wheels (I) onto Axle, then add another Flat Washer (Z) and, thereafter, insert lynch Pins (K)

Step 2

(1) Attach Vertical Support (B) to the Bottom Shelf (A) using Bolts 6 mm x 10 mm (S), Spring Washers

(Y) and lock Nuts (V)

(2) Hand tighten all the Bolts & Nuts at this stage, to be fully tightened later

Step 3

(1) Attach the MIG / Tig Gun leads Hanger (N) upward and facing outward on each Side Support Rail using

2 Bolts 6 mm x 10 mm (S), lock Washers (Y) and lock Nuts (V),

(2) Fasten Side-support Rails (E) to the Bottom Shelf using Bolts 6 mm x 10 mm (S). Lock Washers (Y)

and lock Nuts (V)

(3) Attach the Center Shelf (D) with Flanges facing upwards. Start by fastening Rear holes ﬁrst and then

the side holes using Bolts 6 mm x 10 mm (S), Lock Washers (Y) and Lock Nuts (V)

Step 4 Fasten the Top Shelf (C) using the same procedure as attaching the Center Shelf (D), as shown in Step. 3 (3)

Step 5 Fit Handle (F)I using 4 Bolts 6 mm x 13 mm (T), Lock Washers (Y) and Lock Nuts (V), to the Top Shelf (C)

Step 6 Tighten all the Bolts securely with the Wrench, if left loose earlier

Step 7 Attach both the Chains using 4 Bolts 6 mm x 20 mm (U). Flat Washers (X) and Hex Nuts (W) to the Verti-

cal Support (B) in the eyelets provided. Tighten the Bolts securely with the Wrench

The MIG Cart is now Ready for use!

Firepower welding/ cutting cart instructions

0-5373, Rev. AB 5 June, 2015

H

B

A

V

G

A

Y

S

V

Y

V

Y

V

Y

S

Z

V

Y

Z

K

I

1

2

3

S

V

Y

V

Y

V

Y

V

Y

V

Y

V

Y

S

N

E

D

Art # A-12873

Firepower welding/ cutting cart instructions

June, 2015 6 0-5373, Rev. AB

4

5

V

Y

S

V

Y

V

Y

WX

U

X

Y

T

Art # A-12874

Firepower welding/ cutting cart instructions

0-5373, Rev. AB 7 June, 2015

General Dimension

2”

50mm

3.5”

88mm

29”

725mm

13”

325mm

11”

275mm

12”

300mm

18”

450mm

5”

125mm

31”

775mm

23”

575mm

13”

325mm

21”

525mm

17”

425mm

11”

275mm

28”

700mm

12”

300mm

Art # A-12875

Gross Weight: 34lbs15.4kg

Peso Bruto: 34libras15.4kg

Poids Brut: 34lb15.4kg

Net Weight: 31lbs14kg

Peso Neto: 31libras14kg

Poids Net: 31lb14kg

Page is loading ...

Customer Service: 1-800-858-4232 •Technical Service: 1-800-426-1888 •FAX: 1-800-535-0557

ESAB Firepower Welding/Cutting Cart Troubleshooting instruction

This manual is also suitable for

ESAB Firepower Welding/Cutting Cart Troubleshooting instruction

in other languages

Related papers

Other documents