AmazonBasics B07Y2F9HMX User manual

Brand: AmazonBasics

Model: B07Y2F9HMX

Type: User manual

This manual is also suitable for

B07Y2CNMZN

Adjustable Bed Base with No Massage

Base de Lit Réglable sans Dispositif de Massage

Base para Cama Ajustable sin Masajeador

B07Y2F9HMX, B07Y2D8SF7, B07Y2CNMZN

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

IMPORTANT SAFETY

INSTRUCTIONS

Read these instructions carefully and retain them for future use.

If this product is passed to a third party, then these instructions

must be included.

WARNING

To reduce the risk of burns, ﬁre, electric shock, or injury

to persons:

• Read all instructions before using the furnishing.

DANGER

To reduce the risk of electric shock; always unplug this

furnishing from the electrical outlet before cleaning or servicing.

WARNING

Risk of injury! Keep children away from the foot support.

CAUTION

Risk of injury and ﬁre! Connect only to the furnishing

speciﬁed in this instruction manual.

• Unplug from outlet before putting on or taking off parts.

• Close supervision is necessary when this furnishing is used by, or

near children, invalids, or disabled persons.

• Use this furnishing only for its intended use as described in these

instructions. Do not use attachments not recommended by the

manufacturer.

• Never operate this furnishing if it has a damaged cord or plug, if it is

not working properly, if it has been dropped or damaged, or dropped

into water. Return the furnishing to a service center for examination

and repair.

• Keep the cord away from heated surfaces.

• Never drop or insert any object into any opening.

• Do not use outdoors.

• Do not operate where aerosol (spray) products are being used or

where oxygen is being administered.

• To disconnect, turn all controls to the off position, then remove plug

from outlet.

• To reduce the risk of electric shock, this furnishing has a polarized

plug (one blade is wider than the other). This plug will ﬁt in a polarized

outlet only one way. If the plug does not ﬁt fully in the outlet, reverse

the plug. If it still does not ﬁt, contact a qualiﬁed electrician to install

the proper outlet. Do not change the plug in any way.

Battery Warnings

• Exhausted batteries should be immediately removed from the remote

control and properly disposed.

• If the battery leaks avoid contact with skin and eyes. Rinse affected

areas immediately with plenty of clean water, then consult a doctor.

SAVE THESE INSTRUCTIONS

Intended Use

• This furnishing is a motorized bed base with a wireless remote

intended to hold and adjust the position of a mattress.

• This furnishing is intended for household use only. It is not intended

for medical or therapeutic use.

• This furnishing is intended to be used in dry indoor areas only.

• No liability will be accepted for damages resulting from improper use

or non-compliance with these instructions.

Before First Use

• Check the furnishing for transport damages.

• Remove all the packing materials.

• Before connecting the furnishing to the power supply, check that the

power supply voltage and current rating corresponds with the power

supply details shown on the furnishing rating label.

DANGER

Risk of suffocation! Keep any packaging materials

away from children – these materials are a potential source of danger,

e.g. suffocation.

Product Description

Base frame

Power supply with plug

Mattress holder

Bed leg x4

Remote control with LED light

G K

H L

I M

J N

Battery compartment

Head and foot up

Head up

Head down

Flashlight button

Head and foot down

Foot up

Foot down

Flat

Operation

Inserting batteries

1.5V-AAA

• Remove the battery compartment (F) cover on the backside of the

remote control (E).

• Insert 2x 1.5 V AAA batteries (not included).

• Close the battery compartment (F) cover.

Assembly

NOTICE

Review the assembly instructions to conﬁrm that the

appropriate critical components and accessories are being used with

the furnishing.

• Unfold the base frame (A).

• Attach the bed legs (D) on the base frame (A).

• Flip the base frame (A) over.

• Install the mattress holder on the end of the base frame (C).

Connect to power

• Connect the plug (B) to a suitable socket-outlet.

Functions

(G): The head and foot of the base frame (A) rises up at the

same time.

(H): The head of the base frame (A) rises up.

(I): The head of the base frame (A) lowers.

(J): Turn on/off the ﬂashlight on the remote control (F).

(K): The head and foot of the base frame (A) lowers at the

same time.

(L): The foot of the base frame (A) rises up.

(M): The foot of the base frame (A) lowers.

(N): The base frame (A) resets to the original ﬂat position.

max. 65°

max. 6.2" (15.8 cm)

Pairing

• If the remote control (E) is not synced, press the recover button on

the main unit under the base frame (A).

• Hold the head down (I) and foot up (L) buttons for

10seconds. A beep is heard when the remote control (E) is synced.

Cleaning and Maintenance

WARNING

Risk of electric shock! To prevent electric shock,

unplug the furnishing before cleaning.

WARNING

Risk of electric shock! During cleaning do not

immerse the electrical parts of the furnishing in water or other liquids.

Never hold the furnishing under running water.

Cleaning the base frame (A)

• To clean the metal parts of the furnishing, wipe with a soft,

slightly moist cloth.

• Dry the furnishing after cleaning.

• Never use corrosive detergents, wire brushes, abrasive scourers,

metal or sharp utensils to clean the furnishing.

Cleaning the covers on the base frame

Machine wash 65-85 °F (30 °C)

Do not tumble dry. Do not bleach.

Do not iron. Do not dry clean.

• Use a mild detergent or warm water to spot clean the covers.

• For deep cleaning, remove the covers to hand or machine wash.

• Let the covers dry before reattaching them to the base frame (A).

Maintenance

• Any other servicing than mentioned in this manual should be

performed by a professional repair center.

FCC Compliance Statement

1. This device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

2. Changes or modiﬁcations not expressly approved by the party

responsible for compliance could void the user’s authority to operate

the equipment.

FCC Interference Statement

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

Canada IC Notice

This device contains licence-exempt transmitter(s)/receiver(s) that comply

with Innovation, Science and Economic Development Canada’s licence-

exempt RSS(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference

that may cause undesired operation of the device.

• This equipment complies with Industry Canada radiation exposure

limits set forth for an uncontrolled environment.

• This Class B digital apparatus complies with Canadian

CANICES-3(B) / NMB-3(B) standard.

Speciﬁcations

Model number: GXA09

Actuator rating: 24V , 3 A (max)

Max. weight limit: 300 lbs (136 kg)

Max. height limit: 5.8' (177 cm)

Net weight: approx. 90.9 lbs (41.2 kg)

Dimensions (L x W x H):

approx. 80 x 39 x 14"

(203 x 99 x 35.5cm)

Model number: GXA09

Actuator rating: 24V , 3 A (max)

Max. weight limit: 300 lbs (136 kg)

Max. height limit: 5.8' (177 cm)

Net weight: approx. 110 lbs (49.8 kg)

Dimensions (L x W x H):

approx. 75 x 54 x 14"

(190 x 137 x 35.5cm)

Model number: GXA09

Actuator rating: 24V , 3 A (max)

Max. weight limit: 300 lbs (136 kg)

Max. height limit: 5.8' (177 cm)

Net weight: approx. 120 lbs (54.4 kg)

Dimensions (L x W x H):

approx. 80 x 60 x 14"

(203 x 152 x 35.5cm)

Power supply

Model number: W58RA198-290020

Power rating: 100-240V~, 50/60Hz 1.5 A

Power output: 29 V , 2 A

Classiﬁcation: Class 2 Power unit

Manufacturer:

No. 81, Xuefu Road, Nanshan

District, Shenzhen, Guangdong

Province, China

Remote control

Model number: GXRC18

Voltage/battery type: 3 V , 2x 1.5V AAA (not included)

Light: 1 x LED bulb

Feedback and Help

Love it? Hate it? Let us know with a customer review.

AmazonBasics is committed to delivering customer-driven products

that live up to your high standards. We encourage you to write a review

sharing your experiences with the product.

amazon.com/review/review‑your‑purchases#

amazon.com/gp/help/customer/contact‑us

amazon.com/AmazonBasics

V01-12/19

MADE IN CHINA

FABRIQUÉ EN CHINE

HECHO EN CHINA

AmazonBasics B07Y2F9HMX User manual

Brand: AmazonBasics

Model: B07Y2F9HMX

Type: User manual

This manual is also suitable for

B07Y2CNMZN

Download PDF

report

AmazonBasics B07Y2F9HMX User manual

This manual is also suitable for

AmazonBasics B07Y2F9HMX User manual

Related papers

Other documents