Sabrent USB-DSC9 User manual

Category
Interface hubs
Type
User manual

Sabrent USB-DSC9:

Connect your 2.5 or 3.5 inch SATA/IDE Hard Drives externally to your computer through a USB 3.0 port.

Features:

  • Easy to use plug-and-play installation with no drivers required
  • Supports both 2.5" and 3.5" SATA and IDE hard drives
  • Includes both IDE and SATA cables for wide compatibility
  • USB 3.0 interface for fast data transfer speeds up to 5Gbps
  • LED activity lights to indicate power and data transfer status
  • External power supply for larger capacity hard drives or unstable USB ports

Possible use cases:

  • Data recovery from old hard drives
  • Expanding storage capacity for laptops and desktops

Sabrent USB-DSC9:

Connect your 2.5 or 3.5 inch SATA/IDE Hard Drives externally to your computer through a USB 3.0 port.

Features:

  • Easy to use plug-and-play installation with no drivers required
  • Supports both 2.5" and 3.5" SATA and IDE hard drives
  • Includes both IDE and SATA cables for wide compatibility
  • USB 3.0 interface for fast data transfer speeds up to 5Gbps
  • LED activity lights to indicate power and data transfer status
  • External power supply for larger capacity hard drives or unstable USB ports

Possible use cases:

  • Data recovery from old hard drives
  • Expanding storage capacity for laptops and desktops
User Manual
USB 3.0 TO SATA/IDE Hard Drive Converter
With Power Supply & LED Activity Lights
USB-DSC9
USB-DSC9 / User Manual
1
1-Connect the short 2.5” IDE connector from the Sabrent adapter
to the pins on your 2.5” Hard Drive.
2.5” HDD IDE
USB-DSC9 / User Manual
2
Please Note: When you remove a hard drive from an existing laptop,
you may need to first remove the outer cage and sometimes an additional converter
that is covering the IDE or SATA connectors.
IDE SATA
The Hard Drive Connectors must be exposed
to connect the adapter
USB-DSC9 / User Manual
3
2-Connect the USB cable from the Hard Drive Adapter to an available USB port
on your computer.
3-In most cases, the USB cable will supply sufficient power
for the drive to spin up and initiate.
Some larger capacity Hard Drives may require more power than USB
to provide sufficient power to initiate.
You may need to use the supplied power supply to provide the extra needed power
USB-DSC9 / User Manual
4
USB-DSC9 / User Manual
5
USB-DSC9 / User Manual
6
3.5” HDD IDE
1-Connect the IDE power adapter directly in the IDE drive
USB-DSC9 / User Manual
7
2-Connect the long 3.5 inch IDE connector to the pins on your hard drive
Note the keyed pin and slot and make sure that the drive and the device line up properly
and are securely connected
3-Connect the USB cable from the Sabrent converter to
an available USB port on your computer
USB-DSC9 / User Manual
8
1-Connect the Sabrent converter to the power adapter, and then
plug the SATA power end into the SATA drive directly
2.5”/3.5” HDD SATA
USB-DSC9 / User Manual
9
2-Connect the SATA data cable into the Sabrent Converter, and then
connect the other end directly into the SATA drive
3-Connect the USB cable from the Sabrent converter to
an available USB port on your computer
10
USB-DSC9 / User Manual
The Hard Drive should now spin/vibrate, indicating that the Hard Drive is powering
up.
If the Hard Drive does not spin, it may indicate that the hard drive itself is no longer
working. Quite often, older laptops or desktops that have failed may also have a
malfunctioning hard drive. HDD Enclosures can only access working drives.
A Drive letter should appear in MY COMPUTER, indicating that the Hard Drive has
mounted and the data is accessible.
1. Try connecting to a different USB port on the computer
(Sometimes rear ports work more reliable than front panel ports)
2. Try connecting to a different computer
3. Try using a different Hard Drive
If that still does not work, that may indicate that the adapter itself is not working and
needs to be replaced.
If 2.5” drives work but 3.5” drives do not, you may only need a new power supply.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

Sabrent USB-DSC9 User manual

Category
Interface hubs
Type
User manual

Sabrent USB-DSC9:

Connect your 2.5 or 3.5 inch SATA/IDE Hard Drives externally to your computer through a USB 3.0 port.

Features:

  • Easy to use plug-and-play installation with no drivers required
  • Supports both 2.5" and 3.5" SATA and IDE hard drives
  • Includes both IDE and SATA cables for wide compatibility
  • USB 3.0 interface for fast data transfer speeds up to 5Gbps
  • LED activity lights to indicate power and data transfer status
  • External power supply for larger capacity hard drives or unstable USB ports

Possible use cases:

  • Data recovery from old hard drives
  • Expanding storage capacity for laptops and desktops

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI