Acer AW2000ht-AW170ht F1 User manual

Acer AW2000ht

Service Guide

PART NO.:

PRINTED IN TAIWAN

ii Chapter 3

Preface

1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION

decided for Gateway's "global" product offering. To better fit local market requirements and enhance

product competitiveness, your regional office MAY have decided to extend the functionality of a machine

(e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be

covered in this generic service guide. In such cases, please contact your regional offices or the

responsible personnel/channel to provide you with further technical details.

2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information

available on your regional web or channel. If, for whatever reason, a part number change is made, it will

not be noted in the printed Service Guide. For GATEWAY-AUTHORIZED SERVICE PROVIDERS, your

Gateway office may have a DIFFERENT part number code to those given in the FRU list of this printed

Service Guide. You MUST use the list provided by your regional Gateway office to order FRU parts for

repair and service of customer machines.

Revision History

Please refer to the table below for the updates made on Acer AW2000ht service guide.

Copyright

transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in

any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without

the prior written permission of Acer Inc.

Disclaimer

The information in this guide is subject to change without notice.

Acer Inc. makes no representations or warranties, either expressed or implied, with respect to the

contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular

purpose. Any Acer Inc. software described in this manual is sold or licensed "as is". Should the programs

prove defective following their purchase, the buyer (and not Acer Inc., its distributor, or its dealer)

assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages

resulting from any defect in the software.

Acer is a registered trademark of Acer, Inc.

Intel and Xeon are registered trademarks of Intel Corporation.

Pentium and Pentium II/III are trademarks of Intel Corporation.

Other brand and product names are trademarks and/or registered trademarks of their respective holders.

Date Chapter Updates

Chapter 3 iii

Conventions

The following conventions are used in this manual:

Screen messages Denotes actual messages that

appear on screen.

NOTE Gives bits and pieces of additional

information related to the current

topic.

WARNING Alerts you to any damage that might

result from doing or not doing

specific actions.

CAUTION Gives precautionary measures to

avoid possible hardware or software

problems.

IMPORTANT Reminds you to do specific actions

relevant to the accomplishment of

procedures.

iv Chapter 3

Safety, Care and Regulatory Information

Before installing a server, be sure that you understand the following warnings and cautions.

WARNING: To reduce the risk of electric shock or damage to the equipment:

Do not disable the power cord grounding plug. The grounding plug is an important safety feature.

Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times.

Unplug the power cord from the power supply to disconnect power to the equipment.

Do not route the power cord where it can be walked on or pinched by items placed against it. Pay particular

attention to the plug, electrical outlet, and the point where the cord extends from the server.

WARNING:To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system

components to cool before touching them.

CAUTION: Do not operate the server for long periods with the access panel open or removed.

Operating the server in this manner results in improper airflow and improper cooling that can lead to thermal

damage.

Preventing electrostatic discharge

To prevent damaging the system, be aware of the precautions you need to follow when setting up the system

or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards

or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.

To prevent electrostatic damage:

•Avoid hand contact by transporting and storing products in static-safe containers.

•Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations.

•Place parts on a grounded surface before removing them from their containers.

•Avoid touching pins, leads, or circuitry.

•Always be properly grounded when touching a static-sensitive component or assembly.

Server warnings and cautions

Before installing a server, be sure that you understand the following warnings and cautions.

WARNING: To reduce the risk of electric shock or damage to the equipment:

1. Do not disable the power cord grounding plug. The grounding plug is an important safety feature.

2. Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times.

3. Unplug the power cord from the power supply to disconnect power to the equipment.

4. Do not route the power cord where it can be walked on or pinched by items placed against it. Pay

particular attention to the plug, electrical outlet, and the point where the cord extends from the server.

WARNING:To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system

components to cool before touching them.

CAUTION: Do not operate the server for long periods with the access panel open or removed. Operating the

server in this manner results in improper airflow and improper cooling that can lead to thermal damage.

v

Table of Contents

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ii

Safety, Care and Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

System components 1

System parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Removal and replacement procedures 7

Extend the server from the rack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Power down the server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Remove the server from the rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

System specifications 13

Hardware specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Mechanical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Power supply specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

System appearance 17

Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Rear view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Internal components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Switch and LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

System block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Mainboard 23

Mainboard connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Mainboard jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Mainboard LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

SATA ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

SATA backplane board 29

Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Hardware removal and installation 33

Optional parts installation and removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Hard disk drive removal and installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Power supply removal and installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Top cover removal and installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Replacing a system fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Fan holder removal and installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Replacing a server node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

PCI Express card removal and installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Replacing the riser card module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Removing and installing the cover plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Air shroud removal and installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Heatsink removal and installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

CPU removal and installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Memory removal and installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Mainboard removal and installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Battery removal and installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Rackmount installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

vi

Table of Contents

System diagnositcs 63

System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

AMI BIOS Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

BMC Event Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

BIOS Setup 67

Main setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Advanced Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Advanced Chipset Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Security Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

System Management Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79

Exit Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

BIOS Beep Codes 81

BIOS POST Error Messages List 85

Using Gateway Smart Console 87

Accessing Gateway Smart Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Gateway Smart Console user interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

Chapter 1 1

Item Description Item Description

1 Cover olates 12 Riser card

2 Mainboards 13 Mainboard adapter cards

3 Memory modules 14 Mainboard tray supporting brackets

4 CPUs 15 Mainboard trays

5 CPU heatsinks 16 Top cover

6 Chassis 17 Rail set

7 Power supply 18 Hard disk drive

8 Riser card brackets 19 HDD backplane

9 Adapter card supporting plates 20 Fans

10 Add-on-card power adapter cards 21 Fan holders

11 Riser card 22 Air shrouds

System components

Chapter 1

2Chapter 1

System parts list

Category ODM Description Acer PN

BOARD

HOT-PLUG BACKPLANE

BOARD

2U Twin HDD Backplane support Sup 6x3.5” SATA hdd; hot swap TBC

MAIN BOARD Acer GW170ht F1 Node Kit TBC

Acer GW170htq F1 Node Kit TBC

NETWORK CARD Intel® Gigabit ET Dual Port Server Adapter, Gigabit 10/100/1000

Mbps, PCIe, Dual Port E1G42ETG1P20 (Portville DT) NI.31000.002

Intel® Gigabit ET Quad Port Server Adapter, Gigabit Adapter 10/100/

1000 Mbps, PCIe, Quad Port E1G44ETG1P20 (Portville QT) NI.31000.003

Intel® Gigabit CT Desktop Adapter, Gigabit Adapter10/100/1000 Mbps

connection for PCI Express EXPI9301CTG1P20 (Shelter Island) NI.31000.004

Intel® Ethernet Server Adapter X520-DA2, 10Gb, Dual ports, Direct

attach, E10G42BTDA NI.31000.005

Intel® Ethernet Server Adapter X520-SR2, Dual ports, SR,

E10G42BFSR NI.31000.006

Intel® Ethernet Server Adapter X520-SR1, Single port, SR,

E10G41BFSR NI.31000.007

Intel® Ethernet Server Adapter X520-LR1, Single port, LR,

E10G41BFLR NI.31000.008

POWER DISTRIBUTION

MODULE

SC827 24PIN SPECIAL OUTPUT POWER DISTRIBUTOR 55.R6109.004

RISER BOARD (default)

1 PCI-E Gen2 x16 link (w/ x16 connector, 2U) TA.32100.009

RISER BOARD (optional)

2 PCI-E Gen2 x8 link (w/ x16 connector, 2U) TA.32100.010

VGA CARD

nVidia Tesla C1060 Tesla PCI-Ex16 External power with one 2x3 and

one 2x4 connectors VG.0500Y.001

6GB GDDR5, 4.376" x 9.75" x 1.52", Active Fan, 1 2x3pin extra power

connector and 1 2x4pin extra power connector VG.0600Y.001

Chapter 1 3

SATA BOARD

Promise FastTrak® TX4652 SAS HBA, internal 2-ports, external 2-

ports, PCI-E x1 TA.SAS00.016

LSI SAS 3442E-R, SAS HBA, Internal 4 SAS ports (one SFF8484 SAS

connector), external 4 SAS ports (one SFF8470 SAS connector), PCI-

E x 8

TA.SAS00.027

POWER SUPPLY

1400W 1U GOLD LEVEL PWS W/PM BUS PY.14M0S.001

CASE/COVER/BRACKET ASSEMBLY

CHASSIS

Acer OEM black SC827HD chassis w/o R1400W HS.R7900.001

AIR SHROUD

1U Air shound for AW2000ht/GW2000ht TBC

DUMMY NODE SC827HD motherboard tray (Hot-swap, 2U height) MCP-220-

82705-0N

3.5" HDD CARRIER

3.5" HDD CARRIER TC.31300.005

3.5" HDD DUMMY

3.5" HDD Dummy (12 pcs included in chassis) TC.31300.007

Category ODM Description Acer PN

4Chapter 1

3.5" HARD DISK DRIVE 2TB, Seagate 3.5" SATA2 7200RPM, 7200.12 , "Constellation ES"

32MB

KH.02K01.001

KH.02KW1.001

1TB, Seagate 3.5" SATA2 7200RPM, 7200.12 , "Constellation ES"

32MB

KH.01K01.012

KH.01KW1.012

500GB, Seagate 3.5" SATA2 7200RPM, 7200.12 , "Constellation ES"

32MB

KH.50001.016

KH.500W1.016

1TB, WD RE3 SATA2 7200RPM, WD1002FBYS, 3Gb/s, 32MB KH.01K08.007

KH.01KW8.007

500GB, WD RE3 SATA2 7200RPM, WD5002ABYS, 3Gb/s, 32MB KH.50008.019

KH.500W8.019

250GB, WD RE3 SATA2 7200RPM, WD2502ABYS, 3Gb/s, 32MB KH.25008.026

KH.250W8.026

LEFT HANDLE WITH

FRONT CONTROL

PANEL

Left Handle with Front Control Panel (Node A only) MCP-290-

82703-0V-AI34

RIGHT HANDLE WITH

FRONT CONTROL

PANEL

Right Handle with Front Control Panel (Node B only) MCP-290-

82704-0V-AI34

RAIL KITS Rail Set, quick release for 2,3U 17.2"W (Also included in chassis) 33.R6109.001

CPU

Xeon DP Quad-Core X5570 (Nehalem-EP, 2.93G, 8MB, 6.40 GT/s QPI,

DDR3-1333, LGA1366, 95W, D-0, AT80602000765AA, SLBF3)

KC.55701.EPX

KC.557W1.EPX

Xeon DP Quad-Core X5560 (Nehalem-EP, 2.80G, 8MB, 6.40 GT/s QPI,

DDR3-1333, LGA1366, 95W, D-0, AT80602000768AA, SLBF4)

KC.55601.EPX

KC.556W1.EPX

Xeon DP Quad-Core X5550 (Nehalem-EP, 2.66G, 8MB, 6.40 GT/s QPI,

DDR3-1333, LGA1366, 95W, D-0, AT80602000771AA, SLBF5)

KC.55501.EPX

KC.555W1.EPX

Xeon DP Quad-Core E5540 (Nehalem-EP, 2.53G, 8MB, 5.86 GT/s QPI,

DDR3-1066, LGA1366, 80W, D-0, AT80602000789AA, SLBF6)

KC.54001.EPE

KC.540W1.EPE

Xeon DP Quad-Core E5530 (Nehalem-EP, 2.40G, 8MB, 5.86 GT/s QPI,

DDR3-1066, LGA1366, 80W, D-0, AT80602000792AA, SLBF7)

KC.55301.EPE

KC.553W1.EPE

Xeon DP Quad-Core E5520 (Nehalem-EP, 2.26G, 8MB, 5.86 GT/s QPI,

DDR3-1066, LGA1366, 80W, D-0, AT80602002091AA, SLBFD)

KC.55201.EPE

KC.552W1.EPE

Xeon DP Quad-Core E5507 (Nehalem-EP, 2.26G, 4MB, 4.80 GT/s QPI,

DDR3-800, LGA1366, 80W, AT80602000795AA, SLBKC, D-0) KC.50701.EP5

Xeon DP Quad-Core E5506 (Nehalem-EP, 2.13G, 4MB, 4.80 GT/s QPI,

DDR3-800, LGA1366, 80W, D-0, AT80602000798AA, SLBF8)

KC.50601.EP5

KC.506W1.EP5

Xeon DP Dual-Core E5503 (Nehalem-EP, 2.00G, 4MB, 4.80 GT/s QPI,

DDR3-800, LGA1366, 80W, AT80602003636AA, SLBKD, D-0) KC.50301.EP5

Xeon DP Quad-Core E5504 (Nehalem-EP, 2.00G, 4MB, 4.80 GT/s QPI,

DDR3-800, LGA1366, 80W, D-0, AT80602000801AA, SLBF9)

KC.50401.EP5

KC.504W1.EP5

Category ODM Description Acer PN

Chapter 1 5

Xeon DP Dual-Core E5502 (Nehalem-EP, 1.86G, 4MB, 4.80 GT/s QPI,

DDR3-800, LGA1366, 80W, D-0, AT80602000804AA, SLBEZ)

KC.50201.EP5

KC.502W1.EP5

Xeon DP Quad-Core L5530 (Nehalem-EP, 2.40G, 8MB, 5.86 GT/s QPI,

DDR3-1066, LGA1366, 60W, D-0, AT80602002937AB, SLBGF)

KC.55301.EPL

KC.553W1.EPL

Xeon DP Quad-Core L5520 (Nehalem-EP, 2.26G, 8MB, 5.86 GT/s QPI,

DDR3-1066, LGA1366, 60W, D-0, AT80602000810AA, SLBFA)

KC.55201.EPL

KC.552W1.EPL

Xeon DP Quad-Core L5506 (Nehalem-EP, 2.13G, 4MB, 4.80 GT/s QPI,

DDR3-800, LGA1366, 60W, D-0, AT80602002712AA, SLBFH)

KC.50601.EPL

KC.506W1.EPL

Intel Xeon DP Six-Core X5670 (Westmere-EP, 2.93GHz, 12MB, 6.4GT/s

QPI, DDR3-1333, LGA1366, 95W, AT80614005130AA, SLBV7, B-1)

KC.56701.EPX

KC.567W1.EPX

Intel Xeon DP Six-Core X5660 (Westmere-EP, 2.80GHz, 12MB, 6.4GT/s

QPI, DDR3-1333, LGA1366, 95W, AT80614005127AA, SLBV6, B-1)

KC.56601.EPX

KC.566W1.EPX

Intel Xeon DP Six-Core X5650 (Westmere-EP, 2.66GHz, 12MB, 6.4GT/s

QPI, DDR3-1333, LGA1366, 95W, AT80614004320AD, SLBV3, B-1)

KC.56501.EPX

KC.565W1.EPX

Intel Xeon DP Quad-Core E5640 (Westmere-EP, 2.66GHz, 12MB, 5.86GT/s

QPI, DDR3-1066, LGA1366, 80W, AT80614005466AA, SLBVC, B-1)

KC.56401.EPE

KC.564W1.EPE

Intel Xeon DP Quad-Core E5630 (Westmere-EP, 2.53GHz, 12MB, 5.86GT/s

QPI, DDR3-1066, LGA1366, 80W, AT80614005463AA, SLBVB, B-1)

KC.56301.EPE

KC.563W1.EPE

Intel Xeon DP Quad-Core E5620 (Westmere-EP, 2.40GHz, 12MB, 5.86GT/s

QPI, DDR3-1066, LGA1366, 80W, AT80614005073AB, SLBV4, B-1)

KC.56201.EPE

KC.562W1.EPE

Intel Xeon DP Quad-Core X5667 (Westmere-EP, 3.06GHz, 12MB, 6.4GT/s

QPI, DDR3-1333, LGA1366, 95W, AT80614005154AB, SLBVA, B-1)

KC.66701.EP5

KC.667W1.EP5

Intel Xeon DP Six-Core L5640 (Westmere-EP, 2.26GHz, 12MB, 5.86GT/s

QPI, DDR3-1066, LGA1366, 60W, AT80614005133AB, SLBV8, B-1)

KC.56401.EPL

KC.564W1.EPL

Intel Xeon DP Quad-Core L5630 (Westmere-EP, 2.13GHz, 12MB, 5.86GT/s

QPI, DDR3-1066, LGA1366, 40W, AT80614005484AA, SLBVD, B-1)

KC.56301.EPL

KC.563W1.EPL

Intel Xeon DP Quad-Core L5609(Westmere-EP, 1.86GHz, 12MB, 5.86GT/s

QPI, DDR3-1066, LGA1366, 40W, AT80614005940AA, SLBVJ, B-1)

KC.60901.PL5

KC.609W1.PL5

FAN

80x38MM 9.5K RPM PWM fan for SC827 (4 pcs included in chassis) HI.30900.006

FAN HOLDER

SC827 FAN holder hold 2 80x38 fans ( 2pcs included in chassis) 33.R6109.002

HEATSINK

1U PASSIVE CPU HS FOR INTEL LGA1366 HI.30900.003

Memory module

Category ODM Description Acer PN

6Chapter 1

Samsung 1GB, M393B2873EH1-CH9,1333 CL9, 1Rx8, 1Gb E-die KN.1GB0B.032

KN.1GBWB.032

Samsung 2GB, M393B5673EH1-CH9,1333 CL9, 2Rx8, 1Gb E-die KN.2GB0B.016

KN.2GBWB.016

Samsung 4GB, M393B5273BH1-CH9,1333 CL9, 2Rx8, 2Gb B-die KN.4GB0B.008

KN.4GBWB.008

Samsung 8GB, M393B1K73BH1-CF8,1066 CL7, 4Rx8, 2Gb B-die KN.8GB0B.002

KN.8GBWB.002

Samsung 1GB,M391B2873EH1-CH9,1333, 1Rx8, 1Gb E-die KN.1GB0B.031

KN.1GBWB.031

Samsung 2GB,M391B5673EH1-CH9,1333, 2Rx8, 1Gb E-die KN.2GB0B.015

KN.2GBWB.015

Samsung 4GB,M391B5273BH1-CH9,1333, 2Rx8, 2Gb B-die KN.4GB0B.004

KN.4GBWB.004

TAPE DRIVE (OPTIONAL)

400/800GB, LTO Ultrium-3, External, 1U Rackmount, 3Gb/s SAS,

black color, 2 x eSATA to SFF8088 cable (2m), NA/Asia/Europe power

cables)

TR.40000.007

Quantum ext. LTO-4 1U SAS rackmount TR.40000.009

NAME PLATE

Acer SC827 (GW2000ht) Logo Mylar(Also included in chassis) TBC

Category ODM Description Acer PN

Chapter 2 7

Required tools

You need the following items for some procedures:

•T-10/T-15 Torx screwdriver (included with the server)

Preparation procedures

To access some components and perform certain service procedures, you must perform one or more of the

following procedures:

•Extend the server from the rack

If you are performing service procedures in an Acer branded, telco, or third-party rack

cabinet, you can use the locking feature of the rack rails to support the server and gain access to

internal components.

For more information about telco rack solutions, refer to the RackSolutions.com website

•Power down the server

If you must remove a server from a rack or a non-hot-plug component from a server, power down

the server.

•Remove the server from the rack

If the rack environment, cabling configuration, or the server location in the rack creates awkward

conditions, remove the server from the rack.

•Access the product rear panel

If you are performing certain service procedures, access the product rear panel.

Removal and replacement procedures

Chapter 2

8Chapter 2

Extend the server from the rack

1. If the server is screwed into the rack, remove the screws and set them aside.

Chapter 2 9

2. Grasp the handles and extend the server from the rack.

WARNING:To reduce the risk of personal injury or equipment damage, be sure that the rack is

adequately stabilized before extending a component from the rack.

3. After performing the installation or maintenance procedure, slide the server back into the rack, and then

press the server firmly into the rack to secure it in place.

WARNING:To reduce the risk of personal injury, be careful when pressing the server rail- release

latches and sliding the server into the rack. The sliding rails could pinch your fingers.

4. If necessary, secure the server to the rack with the screws you removed in step 1.

10 Chapter 2

Power down the server

WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment, remove

the power cord to remove power from the server. The front panel Power On/Standby button does

not completely shut off system power. Portions of the power supply and some internal circuitry

remain active until AC power is removed.

IMPORTANT:If installing a hot-plug device, it is not necessary to power down the server.

1. Back up the server data.

2. Shut down the operating system as directed by the operating system documentation.

NOTE: If the operating system automatically places the server in Standby mode, omit the next step.

3. Press the Power On/Standby button to place the server in Standby mode. When the server activates

Standby power mode, the system power LED changes to amber.

IMPORTANT:Pressing the system ID button illuminates the system ID LEDs on the front and rear panels. In a

rack environment, this feature facilitates locating a server when moving between the front and rear of

the rack.

4. Disconnect the power cords.

The system is now without power.

Chapter 2 11

Remove the server from the rack

To remove the server from the rack:

1. Power down the server.

2. Extend the server from the rack

3. Disconnect the cabling and remove the server from the rack. For more information, refer to the

documentation that ships with the rack mounting option.

4. Place the server on a sturdy, level surface.

12 Chapter 2

Chapter 3 13

Hardware specifications

System unit

Specifications Value

Processor socket Two Intel LGA1366

Processor support Quad-Core Intel Xeon 5500 Series

Six-Core Intel Xeon 5600 Series (when available)

Core logic chipsets Intel 5520 IOH-36D - north bridge

Intel ICH10R - south bridge

LAN controller Intel 82576EB Gigabit Ethernet

Memory controller Integrated in 5520 IOH-36D

Storage controller Integrated in ICH10R

VGA controller Matrox G200eW

I/O subsystem Two PCIe x8 slots (per mainboard)

Memory Twelve DDR3-1333 sockets

48GB (Registered) maximum system memory

Independent, mirroring, sparing and lockstep modes

1GB, 2GB, 4GB and 8GB (Registered) DIMMs

Media storage Twelve 3.5-inch bays for hot-plug SATA drives (six per mainboard)

I/O ports Rear (per mainboard): One COM port, One VGA port, Two USB ports, One

embedded NIC port for management, Two Gigabit Ethernet ports, One

Infiniband port (option)

Status LED indicators Front: Power, HDD activity, LAN activity, System ID/status

Rear: LAN activity/status, System ID

Thermal solution Four internal fans (two per mainboards)

One heatsink per processor

System specifications

Chapter 3

14 Chapter 3

Environmental specifications

Specifications Value

Temperature range

Operating

Non-operating

10°C to 35°C (50°F to 95°F) at sea level with an altitude

derating of 1.0°C per every 305 m (1.8°F per every 1000 ft)

above sea level to a maximum of 3050 m (10,000 ft)

-20° - 60° C (-4° - 140° F)

Humidity (non-condensing)

Operating

Non-operating

8 to 90% RH (28°C (82.4°F) maximum wet bulb temperature)

5% to 95% RH (38.7°C (101.7°F) maximum wet bulb

temperature)

Page is loading ...

Acer AW2000ht-AW170ht F1 User manual

This manual is also suitable for

Acer AW2000ht-AW170ht F1 User manual

Related papers

Other documents