Xiamen V7232-8 Wall Hung Smart Toilet User manual

Brand: Xiamen

Model: V7232-8 Wall Hung Smart Toilet

Type: User manual

Thank you for choosing our products. Please read the instructions carefully before installation

and keep it available for future maintenance or reference.

Model: V7232-3 / V7232-8

User Manual

Content

Technical specification

Parts identification

Lid auto open/close

Safety instructions

Specification Parameter

e Others

Description of the knob function

Troubleshooting guide

LED display description

Only for the toilet with LED display

Maintenance

1. Main unit care and maintenance

2. Spray nozzle care and maintenance

3. Filter

maintenance

Emergency troubleshooting

1. Power and water failure

2. Failure of remote control

SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING

When using electrical products, especially when children are present, basic safety precautions

should always be followed, including the following:

1. The appliance is not to be used by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction.

2. This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning use of the appliance in a safe

way and understand the hazards involved.

3. Children shall not play with the appliance.

4. Cleaning and user maintenance shall not be made by children without supervision.

DANGER–To reduce the risk of electrocution:

WARNING– To reduce the risk of burns, electrocution, fire, or injury to persons.

1. Do not place or store product where it can fall or be pulled into a tub or sink.

3. Do not reach for a product that has fallen into water. Unplug immediately.

4. Do not wash the main unit or electrical plug with water or detergent.

5. Do not handle the electrical plug with wet hands.

6. Never block the outlet of the air dryer.

7. Never disassemble, repair or modify this product.

8. During installation, disassembly, repair and maintenance of the product, the power plug

must be switched off and water supply be shut off.

2. Do not place in or drop into water or other liquid.

1. Close supervision is necessary when this product is used by, on, or near children or

individuals with disabilities.

2. Use this product only for its intended use as described in this manual. Do not use

attachments not recommended by the manufacturer.

3. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it

has been dropped or damaged, or dropped into water. Return the product to a service

center for examination and repair.

4. Keep the cord away from heated surfaces.

5. Never use while sleeping or drowsy.

6. Never drop or insert any object into any opening or hose.

7. Do not use outdoors or operate where aerosol (spray) products are being used or where

oxygen is being administered.

8. Connect this product to a properly grounded outlet only. See Grounding Instructions.

9. Do not throw cigarettes and other burning materials into toilet, otherwise it might cause fire.

10. This product is an electric appliance, so it must be placed far away from water and other

liquid.

11. Do not lay the product on its side or upside down during the electrical circuit.

12. It is prohibited to use other electric appliances in the same socket.

13. It is forbidden to use the power extension or unstable loose outlet.

14. Do not reuse any existing water supply hoses, otherwise it might cause leakage, fire or

electrical shock. Installation should include specified components and a new water supply

hose.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION – Failure to follow the instructions may cause bodily injury or property

damage.

GROUNDING INSTRUCTIONS

This product should be grounded. In the event of an electrical short circuit, grounding reduces

the risk of electric shock by providing an escape wire for the electrical current.

The plug must be plugged into an outlet that is properly installed and grounded.

DANGER – Improper use of the grounding plug can result in a risk of electric shock.

If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to

either flat-head terminal.

Check with a qualified electrician or serviceman if the grounding wire instructions are not

completely understood, or if in doubt as to whether the product is properly grounded.

This product is factory equipped with a specific electric cord and plug to permit connection to

a proper electric circuit. Make sure that the product is connected to an outlet having the same

configuration as the plug. No adapter should be used with this product. Do not modify the plug

provided — if it will not fit the outlet, please have the proper outlet installed by a qualified

electrician. If the product must be reconnected for use on a different type of electric circuit, the

reconnection should be made by qualified service personnel.

SAVE THESE INSTRUCTIONS

1. Do not install or use the product in wet places such as a steam room etc.

2. It is recommended to use water-proof electrical outlet which should be installed in a place

where is not easily to get wet.

3. This product should be used with 110V-120V, 50/60Hz electrical current only, load current

is at least 15A. Power plug must be equipped with ground fault circuit interrupter or ground

fault electrical leakage protector or similar high sensitive, rapid type leakage switch. (Rated

sensitive current under 6mA).

4. When it thunders, it is strongly recommended to pull out the power plug.

5. Do not stand on product unit, seat and lid.

6. Do not lean against the lid when using the product, to avoid damage.

7. This product is equipped with a soft-closing seat and lid. Do not push the toilet seat closed,

or damage may occur.

8. Do not use any caustic chemicals or scrubbing brush to clean this product.

9. Exposure to direct sunlight is prohibited.

10. Only use tap water or potable water; otherwise it may cause chafing.

11. Do not connect water supply to a hot water supply. Make sure inlet water temperature is

between 3~35℃/37.4~95℉.

12. Raise room temperature to prevent the toilet from damage due to freezing.

13. When not using the product over three(3) days, drain the water out of the toilet and pull

the electrical plug from the wall outlet.

14. Stop using the product and shut off the power when product malfunctions. Call for

professional service.

15. Means for full disconnection must be incorporated in series in the power input loop of

the same room where the product is installed, that is at the front end of the fixed wiring

to ensure safe use.

Technical specification

Heated seat

Seat sensor, temperature sensor, thermal fuse,

thermostat, leakage protection device

Surface temperature

Heating power

Burn protection

Safety device

6-level adjustment (Neutral level included)

50W

After 10 minutes of use, the seat temperature will

automatically drop slowly to a low level

110V-120V, 50/60Hz

0.08MPa - 0.8MPa (static pressure)

Over 4m/s

6-level adjustment (Neutral level included)

Thermal fuse, Leakage protection device,

Thermostat

200W

1.6/1.1Gpf, 6.0L(full flush) /4.2L(half flush)

Rated power

Main Unit

Toilet

Rated voltage

Cleaning

device

Drying

device

Model

Water proof IPX4

905W

Water pressure range

Flush volume

Flushing mode Washdown

Outlet height

Outlet outside diameter

Drainage method P-trap

102mm

212mm

Heating power

Water temperature 6-level adjustment (Neutral level included)

Water volume

5-level adjustment

Cleaning mode Rear washing /Oscillating washing,

Front washing /Oscillating washing

Automatic nozzle cleaning, Anti-syphon device,

Anti-backflow device, Filter device

1400W

Nozzle position

Water pressure protector

Anti-fouling device

Safety device

3-level adjustment

Warm air speed

Warm air temperature

Heating power

Safety device

V7232-3 / V7232-8

Pressure maintaining device,

Automatic pressure relief device

Thermal fuse, Water temperature sensor,

Ground protection, Thermostat, Over temperature

protection, Leakage protection device

Photocatalyst-free

Deodorization method

Plasma sterilization

Sterilization device

Deodorization

(optional)

Sterilization

(optional)

Seat, Nozzle

Caring device

Night light assembly

User ID setting

Automatic flushing

Intelligent, Always on, Always off

To avoid interference when used by multiple users

Toilet will automatically flush as user walks away

from bowl.

The buzzer is off at night for a quiet environment.

Noise-free setting

Antibacterial site

Difference

description

Lid opening

(optional)

Soft close Lid auto-open

Activate lid opening (optional)

Activate a half flush (optional)

Foot sensor function

(optional)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause

undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected. Consult the dealer or an experienced radio/TV technician for help.

Rated power:

Under the condition of ambient temperature 23℃/73℉, water static pressure 0.18MPa±0.02MPa,

water temperature 15℃/59℉, power toilet on, set water pressure, seat temperature, water

temperature to the highest level in turn and perform one rear washing cycle.

The remote control operates at 2.4 GHz frequency. The main unit performs corresponding

function upon the signal from remote control.

The lid auto open sensor module operates at 24 GHz frequency. The module will sense

movement and open the lid when approached.(Only for the product with lid auto opening/

closing function)

Parts identification

Left side

Right side

Lid

Knob

Bumper

Seat

Ceramic toilet

Touch the sensing

area with foot

(optional)

Spray nozzle

Front washing

Rear washing

Drying shield

Nozzle shield

Night light sensor

Bumper

Lid auto open/close

1. Only for the product with lid auto opening/closing function. This function

is turned off by default. For the first use, please turn on this function by

remote control.

2. If the model you purchased is with foot sensor,

1. When the seat and lid are both closed, touch the sensing area with your foot to open the lid.

2. When the lid is open and seat is closed, touch the sensing area with your foot to close the

lid and activate a half flush.

3. When the seat and lid are open, touch the sensing area with your foot to activate a half

flush.

When user enters the sensing range, the ECO lights

up and the lid opens automatically.

The lid closes automatically 180 seconds after user

leaves.

1. Approaching the toilet

2. Leaving the toilet

Maintenance

Main unit care and maintenance

1. Shut off power supply before doing

maintenance.

2. Use only a soft, damp cloth to clean.

Avoid using harsh chemicals.

3. Once cleaning is completed and all

surfaces are dry, re-connect the power

plug.

Note:

The spray wand will retract automatically

after 10 minutes or if the seat is used.

3. Use only a soft cloth or soft brush to

clean. Do not pull or push the wand, to

avoid damage.

2. When the nozzle moves forward, the

nozzle can be removed and cleaned

separately.

Spray nozzle care and maintenance

1. When no one is seated, turn the knob

clockwise. The nozzle will automatically

stretch out to allow access for cleaning.

4. Put the nozzle back and press the knob

to return the spray wand to its normal

position.

Emergency troubleshooting

Failure of remote control

1. Operate via knob on the main unit.

2. Battery replacement

Remove the remote control from holder.

Open the battery cover and replace the

batteries.

Put the remote control back.

Note:

After battery replacement, the settings

of auto functions and energy saving will

be restored to the defaults. Please reset.

·Put around 8L water into a barrel and flush

the ceramic bowl.

Note: Avoid water spilling from bowl.

Power and water failure

Connect the end

of the bidet

Filter maintenance

1. Turn off power and ball valve, unscrew

water supply hose.

If poor spray performance occurs under

normal conditions:

2. Remove the filter.

3. Clean out filter under running water.

4. Reinstall filter and water supply hose, turn

on ball valve and connect power.

Description of the knob function

1. When seated, turn the knob clockwise to start front washing function, and turn

counterclockwise to start rear washing function. Drying and flushing function are activated

automatically after first washing completion or pressing knob during washing. When

washing again, the same operation only activates drying.

2. When no one is seated, turn the knob clockwise to start manual cleaning function of the

nozzle.

3. During rear and front washing, turn the knob clockwise to move the spray wand forward,

and counterclockwise to move the spray wand backward; Long press the knob to switch

to the water pressure adjustment function. Clockwise rotation increases the water

pressure, while counterclockwise rotation decreases the water pressure. (Note: During

washing, long press the knob to switch between the functions of water pressure

adjustment and spray wand position adjustment.

4. During drying, clockwise rotation increases air temperature and counterclockwise

rotation decreases air temperature.

5. In functional mode, press the knob to stop function in progress: rear washing, front

washing, drying or nozzle cleaning. In addition, press the knob to flush the toilet.

6. To enter into standby mode (not seated), press and hold the knob.

7. To enter into functional mode, press and hold the knob.

Note: Default settings for all functions are intermediate when powering on. Use remote control

to switch to the function level set before.

LED display descriptionOnly for the toilet with LED display

Description of LED display:

1. During self-inspection, icons of sterilization, water temperature, seat temperature and

ECO light up, and the temperature is displayed at 88℉. After self-inspection, sterilization,

water temperature and ECO icons go off and seat temperature icon lights up, showing

current seat temperature. The temperature shows “--” at neutral level.

2. In non-energy-saving mode, seat temperature icon lights up, showing current seat

temperature (temperature in neutral shows "--"). During water temperature adjustment,

seat temperature icon goes off and water temperature icon lights up, showing current

water temperature (temperature in neutral shows "--"). Water temperature icon goes off

and seat temperature is displayed after 10 seconds.

3. During washing, seat temperature icon goes off and water temperature lights up, showing

current water temperature (temperature in neutral shows "--").

4. Sterilization icon lights up when this function turned on, otherwise it goes off.

5. In energy saving mode, ECO icon lights up. Seat temperature in neutral shows "--",

otherwise it shows Level 1.

6. LED display goes off completely when shutting down.

7. LED display goes off completely after 30 seconds once no longer being used. When

seated or pressing any button, LED display is activated to show current status.

8. When user enters the sensing range, LED display lights up showing current status.

Display goes off completely 30 seconds after user leaves. (Only for the toilet with lid auto

open/close function.)

ECO energy savingseat temperature temperature displaywater temperaturesterilization

Troubleshooting guide

Problem Cause

No water from

nozzle

Water supply hose is kinked

Angle valve is off

A water failure occurred

Poor water

spraying

Water supply hose is kinked

Angle valve is not fully

turned on

Filter is clogged

Low water

temperature

The water temperature is not

set properly

Solution

Straighten the hose to remove the

kink

Turn on the angle valve

Restore the water supply

Straighten the hose to remove the

kink

Turn on the angle valve fully

Clean the filter

Adjust the water temperature

Low dryer

temperature

Dryer not blowing

Spray wand

cannot retract

Spray wand

cannot stretch out

Remote control

cannot display

Malfunction of

deodorization

Caution

The dryer temperature is not

set properly

In standby mode or energy

saving mode

Power off

Get stuck by impurities

Power off

User is not within the sensing

area of the seat

The positive and negative

direction of the batteries is

incorrect

User is not within the sensing

area of the seat

Deodorization function

continues after user leaves

If the problem cannot be resolved as per above solutions, please

disconnect the power and contact service providers.

If the power leakage protection switch always trips, it means that

the product is leaking. Please disconnect the power and contact

service providers.

It is normal for the deodorizing

function to continue operating after

user leaves, for complete odor

removal.

Adjust position on seat to activate

the sensor

Reload the batteries

Adjust position on seat to activate

the sensor

Turn on the power

Low battery Replace new batteries

Remove the impurities

Push back the spray wand gently

and put power on

Switch to functional mode to use dry

function

Adjust the dryer temperature

Low seat

temperature

The seat temperature is not

set properly Adjust the seat temperature

In standby mode Switch to functional mode and wait

for 3+ minutes

ASVFA72320008A-1.1

The picture of product may not be entirely consistent with actual appearance and

color because of product improvements, please in kind prevail.

Xiamen V7232-8 Wall Hung Smart Toilet User manual

Brand: Xiamen

Model: V7232-8 Wall Hung Smart Toilet

Type: User manual

Download PDF

report

Xiamen V7232-8 Wall Hung Smart Toilet User manual

Xiamen V7232-8 Wall Hung Smart Toilet User manual

Related papers

Other documents