Funkwerk AUDIO 2010 Operating instructions

Brand: Funkwerk

Model: AUDIO 2010

Type: Operating instructions

Handsfree System

156 8010 1.01

Operating Manual

-2-

Audio 2010

Funkwerk Dabendorf GmbH

Maerkische Straße

D - 15806 Dabendorf

Phone: +49 3377 316 - 0

Fax: +49 3377 316 - 300

[email protected]

www.fwd-online.de

Rights to changes and deviations from the scope of delivery reserved as required by technical pro-

-3-

Table of contents

Audio 2010

Table of contents

Notes on safety ................................................................................ 4

Functions of the Audio 2010 ........................................................... 5

Functional overview ........................................................................... 5

Symbols ............................................................................................ 6

Key functions ..................................................................................... 6

Symbole der Statusleiste ................................................................... 8

Speller symbols .................................................................................. 8

Menu item symbols ........................................................................... 8

Speller ................................................................................................ 9

Operational startup .......................................................................... 9

Bluetooth® technology ..................................................................... 10

Switching on / Switching off ............................................................ 10

Entering PIN Bluetooth® .................................................................. 10

Handsfree mode (handsfree profile) ................................................ 11

Automatic connecting ...................................................................... 11

Calling ............................................................................................... 11

The menus ....................................................................................... 13

Voice control .................................................................................. 24

Language .......................................................................................... 24

Activation and sequence .................................................................. 25

Service ............................................................................................. 28

FAQ - Frequently Asked Questions .............................................. 29

Software updating ......................................................................... 31

Hotline ............................................................................................. 31

-4-

Audio 2010

Notes on safety

IMPAIRMENT OF TRAFFIC SAFETY!

Inattention can lead to dangerous traffic situations. Also in the

handsfree mode, you must always pay attention to the traffic situa-

tion. The telephone may be used by the driver during driving in

handsfree mode only! Dispense with a telephone call in difficult

situations, as appropriate!

NOTE:

Dependent on the software, it can be that individual functions are

not yet available! Please note the information about this at

www.fwd-online.de.

-5-

Functions of the Audio 2010

Audio 2010

Functions of the Audio 2010

Functional overview

•Call functions ➯Incoming call

➯Outgoing call

➯Automatic redialing

•Status indicator ➯Rechargeable battery status of the mobile telephone

➯Network status indicator

➯New SMS

➯Call in absence

➯User icon with initials

➯Multipoint / single connection

•Integrated voice control ➯Call in absence

•Recorded announcement ➯Connection confirmation by voice

➯Name announcement of the incoming

caller

•SMS ➯Reading and answering of SMS messages

•Takeover of the call lists and the telephone directory of the mobile telephone

•Multipoint technology ➯2 mobile telephones are simultaneously

connected with the Audio 2010

•Registration of up to 10 mobile telephones

•Reproduction of music files of the mobile telephone via

Bluetooth® audio-streaming (A2DP)

•iPodTM Player*

* Requires accessories

-6-

Audio 2010

Symbols

The actuator of the Audio 2010 is provided with an OLED display and a total of 8

keys. The display shows a short overview of the existing keys. The functions of

the individual keys are explained in this section.

Key functions

➔

Die -key (green) serves for call acceptance.

A further function is the selection of menu items. During the play-

back of music, the key takes over the function of „Play“ and

„Pause“.

Brief description

Accepting, selection of menu items,

termination of the screen saver

➔

The -key (red) can reject an incoming call and end an ongoing

call. During the playback of music, the title can be stopped with the

-key.

Furthermore, the system can be switched off by short pressing.

Brief description

Hang up, reject, stop, termination of the

screen saver, activate voice dialing of

the telephone

-Key

-Key (red)

-Key (green)

-Key

-Key (Buzzer)

(green)

(red)

-7-

Symbols

Audio 2010

➔

During the music playback, a skip to the next title can be made with .

Furthermore, navigation through the menu and the Speller can be

implemented with this key (explanation Pg. 9.

Brief description:

Title skip forward, navigation through menu and

Speller, termination of the screen saver

➔

The -key serves to skip to the previous title during the music

playback. Furthermore, navigation through the menu and the Speller

can be implemented with this key.

Brief description

Title skip backward, navigation through menu

and Speller, termination of the screen saver

➔

With the -key the volume is increased during a telephone call, with

voice control and during music playback. In addition, navigation

through the menu and the Speller can be implemented with this key.

Brief description

Volume increase, navigation through menu and

Speller, termination of the screen saver

➔

With the -key the volume is reduced during a telephone call, with

voice control and during music playback. In addition, navigation

through the menu and the Speller can be implemented with this key.

Brief description

Volume reduction, navigation through menu

and Speller, termination of the screen saver

➔

The voice control of the Audio 2010 is activated by short pressing of

the voice command key (buzzer). For possible speech commands,

refer to Chapter „Voice control“ (see Page 24).

The mobile telephone's own voice control is activated by long pressing

of the voice command key

NOTE:

The Audio 2010 is provided with a screen saver. After 60 seconds inac-

tivity, the display switches itself off automatically. With any arbitrary

key press, the display can be turned on again. This key press does not

implement any function, rather it switches the display, however this

does not apply for the - key (buzzer) which remains permanently

active.

-8-

Audio 2010

Symbols

Symbols of the status bar

Field strength symbol - Display of the

current reception field strength of the

mobile telephone

SMS symbol - Display for received

SMS

Arrow symbol - Display for call in

absence

Display of the initials of the user

Battery symbol - Mobile telephone is charged

Battery symbol - Display of the storage battery capacity of the

mobile telephone

Display of the initials of the user, as well as display that a

„Multipoint“ connection exists

Speller symbols

Symbol for confirming the input

Symbol for deletion of the last character

Symbol for change to the number input

Symbol for change to the input of lower case letters

Symbol for change to the input of upper case letters

Symbol for change to the input of additional characters

Symbol, to exit the voice command key

Menu item symbols

Activated option: This symbol appears before a menu item if it is

activated as an option.

Deactivated option: This symbol appears before a menu item if it

can be activated as an option.

-9-

Operational startup

Audio 2010

Speller

The Speller is controlled with the -, -

keys. The -key (green) or the -key is

used for confirming the selection, and the

-key (red) in order to end the Speller.

The Speller enables the compiling of individual alphabetic characters or numbers,

as well as telephone numbers or names. It is available for various functions of

the Audio 2010, for example for the dialing of a telephone number or the gene-

ration of a telephone directory entry. The operation of the Speller is explained

below:

➔

Entering numbers

Navigate to a digit by activating the -, -keys and accept this through

pressing the -key (green). You can delete the last digit of the number in

each case through pressing the - symbol. If the number is entered com-

pletely, this can be selected through pressing the - symbol. In order to

exit the Speller, press the -key (red).

➔

Entering name or text

Analogous to the number input, you can also enter names or whole texts

with the Speller. Navigate to a character by activating the -, -keys and

accept through pressing the - key (green). You can delete the last

character in each case through pressing the - symbol. If the name is

entered completely, this can be saved through pressing the - symbol. In

order to exit the Speller, press the -key (red). A switchover between

upper case letters, lower case letters, digits and additional characters is

possible using the symbols described under Chapter „Speller symbol“,

which can be selected with the -, - keys.

Operational startup

Take time to become familiar with the operation of the Audio 2010 in connection

with the mobile telephone. First of all, make some telephone calls where you can

determine the optimal conditions for volume and speech direction before you

use the Audio 2010 in traffic. For operational startup, the vehicle should be par-

ked in a quiet place. A prior arrangement with another call subscriber who can

take some time is advantageous in supporting you in making test connections.

-10-

Audio 2010

Operational startup

Bluetooth® technology

Bluetooth

technology is a radio technology and thus it makes possible commu-

nication without cables. Data and voice can be transmitted simultaneously. No

line of sight connection between the participating devices has to exist for this

purpose. The radio range is 10 m. Faults through other electrical devices or

obstacles in the free field can lead to a lower range. The frequency band in which

Bluetooth

works is released almost worldwide. That, and the fact that every

Bluetooth

product is tested and qualified for trouble-free cooperation with other

Bluetooth

devices, ensures maximum compatibility of devices from different

manufacturers. The Audio 2010 supports the Bluetooth

hands-free profile. This

means that you can operate mobile telephones which support the Bluetooth

hands-free profile. As appropriate, look up in the operating instructions of your

mobile telephone which profile it supports. A2DP (Advanced Audio Distribution

Profile) is a technology which allows the transmission of stereo audio signals wit-

hout wires via Bluetooth

to a corresponding receiver. Please refer to our Inter-

net homepage to find out about compatible mobile telephones.

Switching on / Switching off

With the first operational startup of your Audio 2010, you must start the Audio

2010 through switching on the ignition. You will see the start logo and the main

screen is displayed. If no connection to the mobile telephone exists, or if no user

is found, the main menu has limited functionality. In order to establish a connec-

tion to the Audio 2010, you must select the menu item „User administration“

with the - key (green). A „New user“ is selected there. The Audio 2010 then

searches for mobile telephones in your reception area. If your mobile telephone

should not be found, you can start the search again. As appropriate, please refer

to the section „Problem elimination“. If the name of your mobile telephone is

displayed, select it with the -key (green). After the connection with the

Audio 2010, the full functionality of the main menu is provided. Functionalities

which the mobile telephone does not support are not optional. If the ignition is

switched off, the Audio 2010 switches itself off. If the ignition is switched off

during a telephone call, this telephone call is maintained and continues. The

Audio 2010 is then switched off only on ending the telephone call with hanging

up.

Entering PIN Bluetooth®

After some seconds, you are requested to enter the Bluetooth

PIN. Enter in the

mobile telephone the PIN which is indicated on the display of the Audio 2010.

-11-

Operational startup

Audio 2010

Handsfree mode (handsfree profile)

Under certain circumstances, the coupling with your mobile telephone does not

function in handsfree mode with the above-designated method. If you are sure

that your mobile telephone supports the Bluetooth

hands-free profile, please

proceed as follows: Select the point „Coupling of the telephone“ in the list of the

found devices. You must now search from the mobile telephone for Bluetooth

devices. Please refer to the corresponding operating instructions as to how you

proceed here. The mobile telephone then starts the device identification. In the

list of the devices found by your mobile telephone, select „Audio 2010“. You are

requested to enter a PIN or a password during the coupling procedure of your

mobile telephone. Please enter the series of digits indicated in the display of the

Audio 2010. After a short time, the mobile telephone should report that the

devices are coupled. You can also interrupt the coupling at any time through

pressing the - key (red). If the coupling should not succeed, please refer to

the section „Problem elimination“.

Automatic connecting

If a mobile telephone should already be coupled with the Audio 2010, then the

Audio 2010 attempts to connect with this mobile telephone. The last connected

mobile telephone is always searched for. If the search was successful, a connec-

tion is established automatically. On the other hand, if the search is without suc-

cess, it can be that the Bluetooth

on your mobile telephone or the mobile tele-

phone itself is not switched on, or that you were not the last user. If you wish to

dial, activate this user in the user administration and log them on.

Calling

If a Bluetooth

link exists between the Audio 2010 and the mobile telephone,

you can use the hands-free function of your Audio 2010. If no connection exists,

then the hands-free function cannot be used. Please first establish a Bluetooth

link. You can dial a number by voice dialing, by menu or directly on the mobile

telephone.

Incoming call

The call is signaled to you with the ring tone of your mobile telephone, provided

that the ring tone is supported over the Bluetooth

link. Otherwise a ring tone is

generated in the Audio 2010. If the caller has not blocked the communication of

his call number and the mobile telephone supports this function, the number, or

if a corresponding entry is found in the telephone directory, the name of the cal-

ler, is shown in the display.

-12-

Audio 2010

Operational startup

You can decide whether you accept the call ( -key green) or reject the call

( -key red). If you accept the call, you can regulate the volume with the -,

-keys. The setting-adjustment remains stored. You can end the call by pres-

sing the -key (red).

Making a call

Making a call from the Audio 2010 is possible only if a Bluetooth

link exists bet-

ween the Audio 2010 and the mobile telephone. You have the possibility to

structure a call over the voice dial or over the menu.

In order to activate the voice dial, press the -key. With the command „Select

number“ you have the possibility to speak the telephone number to be selected

and, with the command „Dial <Name>“, a name can be dialed directly from the

telephone directory. You can find further information on that in Chapter „Voice

control“.

In order to start a call, there are available the following possibilities:

➔

Dialing from the telephone directory of the mobile telephone,

➔

Direct dialing of a number with the Speller,

➔

Dialing from the call lists of your mobile telephone,

➔

Using the callback possibility from received SMS messages.

Finally, you still have the possibility to dial a number directly on your mobile tele-

phone.

Start of the voice dial of the telephone

As a result of short pressing of the - key, the telephone-internal voice dial can

be started. With the key -(red) this can be ended again.

Ended call

On completion of the telephone call, the main menu is entered again. If an inco-

ming call is rejected with the -key (red), a skip into the previous menu item

is made.

Volume control

The reproduction volume can be regulated during a call and during an active

speech recognition with the -, -keys.

Options during the telephone call

During the telephone call, the following options can be carried out when the

-key (green) is activated:

-13-

Operational startup

Audio 2010

➔

DTMF tones

➔

Microphone mute

➔

Private mode

➔

DTMF tones

Here, the key tones are selected with Speller and subsequently sent.

➔

Microphone mute

Using this option, the microphone can be switched mute. At this moment, the

call participant cannot hear you any longer. A renewed pressing deactivates the

muting of the microphone.

➔

Private mode

A change into private mode can also be made during a telephone call, where the

point „Private mode“ is selected and confirmed with the -key (green). The

call is now possible over the mobile telephone only. A communication over the

Audio 2010 is suppressed at this moment and the other vehicle occupants

cannot overhear the call. A renewed pressing of the -key (green) ends the

private mode.

IMPORTANT NOTE:

Please consider the legal provisions of your country for making a call in

the car! In most countries, making a call is allowed during driving only

when using a handsfree system.

The menus

With the -, - keys you can navigate to a menu item. Select a menu item

with the -key (green) or the -key and exit the menu with the -key

(red). With renewed pressing of the -key (green), select the submenu of the

current menu. The following menu items are available for selection and are listed

in the following menu overview:

➔

User administration

Under this menu item, user-specific setting-adjustments, such as „Change initi-

als“, „Log on“, „Log off“ etc. can be carried out. However, new users can also

be logged on. Further information on that under Chapter „User administration“.

-14-

Audio 2010

Operational startup

➔

Setting-adjustments

Under this point general setting-adjustments can be carried out for the Audio 2010.

These extend from „Ring tone“ to „Update software“. A precise subdivision can

be taken from the following overview, where the menu structure is represented.

You can find further information in Chapter „Setting-adjustment“.

➔

iPod

Player

The menu „iPod

Player“ offers the possibility to control the iPod

using the

Audio 2010. Under „Options“, a search can be made in different title lists, as is

well known from the iPod

. You can find further information on this in Chapter

„iPod

Player“.

➔

Music Player

The menu „Music Player“ offers the possibility to play music titles and to control

these as usual with „Play“, „Pause“, „Stop“, „Forward“ and „Backward“.

Under „Options“ the playback devices can be coupled with the Audio 2010. You

can find further information on this in Chapter „Music Player“.

➔

Call lists

Includes information of the last selected numbers, the calls accepted and mis-

sed. You can mark an entry with the -, -keys and start a call with the

-key (green). You can find more precise information in Chapter „Call list“.

➔

Telephone directory

The telephone directory includes the entries downloaded from the mobile tele-

phone. Every number of an entry can be accessed. In addition, a direct dial can

be implemented here. You can find further details in Chapter „Telephone direc-

tory“.

➔

Messages

Includes the list of the short messages („SMS“). Unread messages are marked

accordingly. The message menu is sub-divided into „Messages read“ and „New

message“. Further information in Chapter „Messages“.

-15-

Operational startup

Audio 2010

-16-

Audio 2010

Operational startup

User administration

Symbol:

The Audio 2010 allows the administration of up to 10 user profiles, between

which a switchover can be made simply and rapidly during the operation of the

Audio 2010. For every user, the following data (among other things) are stored

individually:

➔

Telephone directory

➔

Display brightness

➔

Ring tone

➔

Display language

➔

Volume settings

➔

Call lists

Open user administration

In order to reach user administration, go into the main menu on symbol and

press -key (green).

You can then view the users who have made a coupling with the Audio 2010 and

the point „New user“. If no users are coupled, select only the point „New user“.

Creating new user

In order to log on a new user, select the point „New user“ with the -, - keys

and press the -key (green). All further steps are analogous to the Chapter

„Operational startup“.

Changing initials of the user

Open the user administration. Then select a user and press the -key (green).

Now you reach a submenu. There you select the point „Change initials“. With

the aid of the Speller you can now change the name of the user.

User change

In order to carry out a user change, go into the user administration and select the

required user. Confirm with pressing the -key (green). A submenu is ope-

ned. Select the point „Log on“. If the selected user can be found, an instant user

change then occurs. If the user cannot be found, a return is made again to the

user administration.

-17-

Operational startup

Audio 2010

Logging on a second user - „Multipoint“

Multipoint is a function which enables the connection of two telephones syn-

chronously with the handsfree system. In this case, the possibility exists to log

on a second user, as well as the active user.

The active user can continue to use all functions of the Audio 2010 which the

mobile telephone supports, where the second user is limited to the functions

„Log on“/„Log off“/„Hang up“.

As a result of the function, you can for example connect your private and com-

mercial telephone synchronously with the Audio 2010.

In order to log on the second user with the Audio 2010, proceed as follows:

➔

Create a new user (see point „Logging on a new user“)

➔

Then change to the active user (see point „User change“)

➔

Go into the menu „User“

➔

Then click on the user which you would like to log on as second user

➔

Now click on „Log on 2nd user“

Logging off users

You can disconnect the current Bluetooth

link under point „Log off“ in the user

administration under the respective user.

Settings

Symbol:

The following setting-adjustments can be carried out:

➔

Ring tone

➔

Software update

➔

Brightness

➔

Information

➔

Main menu configuration

➔

Language

➔

Call settings

➔

Voice control

➔

Connection settings

➔

Audio

➔

Power off delay

➔

Switching off

➔

Reset

Ring tone

The menu „Ring tone“ is sub-divided into „Melody“ and „Volume“. Under

„Melody“ several ring tones are available, which can be correspondingly adju-

sted according to personal taste. The „Volume“ of the ring tone can be set with

the -, - keys.

-18-

Audio 2010

Operational startup

Brightness

➔

Brightness

Here the display lighting can be adapted according to the requirements of the

user.

Main menu configuration

You can fade out certain functions in the main menu. These points are then no

longer displayed in the main menu.

The following points can be configured:

➔

iPod

player

➔

Call lists

➔

Telephone directory

➔

Messages

Call settings

➔

Automatic call acceptance

If this option is activated, an incoming call is accepted automatically after

ringing three times.

Connection settings

➔

User search

You can select between „Search for last user“ and „Search for all users“.

➔

Connection type

You can select between „Connect manually“ and „Connect automatically“.

Power off delay

You can determine how long the Audio 2010 should remain active after shut-

down of the ignition. The delayed switch-off time can be adjusted in steps of bet-

ween 0 and 30 minutes.

Reset

Reset all setting-adjustments to default settings. All user setting-adjustments

also disappear in this case, including telephone directory data.

Software update

The software of your Audio 2010 can be updated over Bluetooth

. You can find

further information in the Chapter „Software updating“.

-19-

Operational startup

Audio 2010

Information

Get informed about the different software and hardware versions of your Audio

2010. Use this information when referring to our service with questions and pro-

blems.

Language

The Audio 2010 supports several display languages. Under this menu item, you

have the possibility to change the display language.

Voice control

➔

Activate

If this point is implemented, the voice control starts. Control is by using sti-

pulated commands. You can find more detailed information on that in the

Chapter „Voice control“.

➔

Language

If your Audio 2010 is provided with several languages for voice control, you

have here the possibility to reset these.

Audio

➔

Microphone sensitivity

Under certain circumstances it can be necessary that the microphone sensi-

tivity be adapted, for example when the microphone was installed very far

from the driver or also very near. In the case of the Audio 2010, ten possible

levels of sensitivity can be selected between. The sensitivity levels are repre-

sented to the right in the display as bars. A total of five bars can be seen,

where one bar represents two stages. The sensitivity can be adapted with

the -, - keys.

➔

Line-In

In this menu item, you can activate the line-in and vary the input volume of

the audio device connected to the line-in of the electronic box.

NOTE:

Please note that the connection of one audio device only is permissible

with line level. If the line-in of the electronic box is overdriven by too

high a signal of the line-out of the audio device, then the volume of the

line-out of the audio device is to be reduced.

-20-

Audio 2010

Operational startup

➔

Telephone announcements

If the connected telephone has navigation functions, it can be set-adjusted

here whether navigation announcements should be output over the Audio

2010. The radio is switched mute during this output. However, key tones of

the telephone are output in the same way as if the telephone generated

these. The status is saved for every user and set to the previously set-adju-

sted status with new start of the system.

Possible states: ON / OFF

➔

Mute delay

Here it can be set-adjusted how long should be waited between the activa-

tion of the mute-switching line and the speech recognition. This is appro-

priate, since car radios require different times for the identification of a mute

signal and the changeover of the audio paths in the radio. The time should be

set-adjusted so that the first announcement of the Audio 2010 „Main menu“

can be heard complete

Possible states: 0.5 sec. / 1.0 sec. / 1.5 sec. / 2.0 sec. / 2.5 sec. / 3.0 sec.

➔

Reset

Reset all audio settings to default values.

Switching off

With this point, the current Bluetooth

link is disconnected and switched off.

The Audio 2010 can be switched on by pressing on a key again.

iPodTM Player

Symbol:

The iPod

Player is activated over the main menu. The activation can be imple-

mented only when the accessory „iDapter“ has been acquired or when acces-

sories have been retrofitted. The iPod

Player can also be activated if no mobile

telephone is coupled with the Audio 2010. In order to enable the playing of music

by the iPod

, an iPod

must be connected on the iDapter cable.

Connecting / Coupling

The connection with the iPod

is implemented automatically after plugging into

the iDapter cable. If the iPod

icon in the main menu remains gray, the connec-

tion has failed. Then the connector of the iDapter cable must be plugged into the

Page is loading ...

Funkwerk AUDIO 2010 Operating instructions

Funkwerk AUDIO 2010 Operating instructions

Funkwerk AUDIO 2010 Operating instructions

Other documents