INSTRUCTION MANUAL
CM-505
5” TFT LCD COLOR MONITOR
Thank you for purchasing this product.
For proper usages and application,
Please read this instruction manual thoroughly.
PRINTED IN KOREA ver. 1.1 * Design and specifications are subject to change without notice.
2
CONTENTS
SAFEGUARD INSTRUCTIONS
FEATURE
CONTENTS
FUNCTION OF EACH PART
FUNCTION
CONNECTIONS
INSTALLATION
Changing REMOTE CONTROL Battery
SPECIFICATION
....................................... 3
............................................................................. 5
.......................................................................... 5
............................................ 6
......................................................................... 8
............................................................... 12
............................................................... 13
.................... 14
.............................................................. 15
3
5” TFT LCD COLOR MONITOR
SAFEGUARD INSTRUCTIONS
Please read the “Safety Rules” carefully before using this product. Following the safety rules pre-
vents users from damages related with the misuse of the product. It is very important to follow
these safety rules. We state “Caution” and “Warning” to clarify any potential risk for a damage
associated with the misuse of the product.
CAUTION
Before install the body, take enough place at least more than 15cm from the wall to
emit heat.
Should install while power off. (After install products, connect DC jack)
- It may cause to electronic shock or malfunction.
Do not place near magnet.
- It may cause malfunction and trouble.
Unplug product when do not use for a long time.
- It may case fire by short circuit due to heating.
Do not use multi socket or extended adaptor.
- It may cause unexpected heating, fire and malfunction.
While stop driving (parking), set the car in motion.
- It may cause battery discharge.
WARNING
This information is for preventing bodily harm or even death and
use should follow this safety rules.
This information is for preventing damage or shorten the life time
of the products.
This information is for user’s reference for better usability.
CAUTION
NOTICE
The battery for remote controller is not rechargeable and should replace same or simi-
lar model. Used battery may cause environmental pollution, so trash it carefully.
- This may cause a malfunction and problem.
4
WARNING
After installing, check it break lamp, head lamp and wipe works properly.
Do not use bolts or nuts from a parts for vehicle.
- Using bolt or nuts from steering column or break may cause an accident.
When the power cable cord touches a metal case, cover it with a friction tape.
- Short circuit or disconnection of wire may cause a fire or accident.
Do not disassemble, repair and remodeling.
- It may cause malfunction and injury, can not get warranty.
- Make inquiries to agent for repair and checkup.
Do not use in problem condition as like smoking, smell something burn.
- It may cause fire. Stop to use and make inquiries to agency.
Do not put a pin or needle on the hole or crack in the body.
- In case of inserting them, stop to operate, it may cause electronic shock, fire and
malfunction.
Do not place where vibration and shock.
- It may cause throw down and then malfunction and accident.
When clean exterior, power off and wipe with dry cloth.
- Wet cloth may cause a electronic shock.
Do not clean exterior with volatility or oily solvent.
Neither keep touching rubber and plastic for long time.
- It may cause change of surface, fall of paint, malfunction and fire.
Keep clean dust on power socket.
- It may cause electronic shock and fire by bad connection.
Do not pull cord with a jerk, should catch a plug and pull. Do not use damaged cord.
- It may cause cord malfunction, electronic shock and fire.
Do not place near of air bag effective range.
- It may cause malfunction of air bag or accident, injury due to hitting monitor by
air bag.
Do not put the product in place where sudden temperature increasing and should use
on optimum voltage, temperature and humidity.
- It may cause to electronic shock or malfunction.
Take care that the product doesn’ t get wet.
- It may cause electronic shock or malfunction.
1
2
* Design and Specications are subject to change without notice.
Monitor Cable TRG Extension
Cable(x2)
5
5” TFT LCD COLOR MONITOR
5” TFT LCD COLOR MONITOR
• Application of TFT LCD with high resolution and low reflection
• All functions are displayed on screen (OSD function)
• PWM volume control
• Mode selection function
• Low energy consuming rate
• Language Display Selection
(ENG-DEU-ITA-FRA-SPA-KOR-JPN)
• 1 Cable solution
• Free voltage (From DC 12V to DC24V)
FEATURE
CONTENTS
• Before use this products, please check below contents. If there is something missing parts,
please contact sales agent.
Cigar CableMonitor Stand(CL-5)
Instruction
Manual
Remote Control
3
MONITOR
6
5” TFT LCD COLOR MONITOR
FUNCTION OF EACH PART
1. MODE
2. DIMMER
3. POWER
4. HEADPHONE
5. REMOTE SENSOR
CAM1 / CAM2 / AV Select function
DAY / NIGHT
POWER ON / OFF Button
Headphone jack
Sensor for receiving signal from the remote control
REMOTE CONTROL
7
1. POWER
2. MODE
3. MENU
4. VOLUME UP/DOWN
5.
6. MUTE
7. RECALL
8. AUTO PIC
Power ON/OFF key
CAM1 / CAM2 / AV selection function
Selecting MENU and changing functions
Adjust volume level
Moving and Adjusting in menu
Mute mode ON/OFF
Displaying the current mode and volume level
Adjusting the screen setting
4
* This manual is written based on remote controller.
CAM1
8
5” TFT LCD COLOR MONITOR
FUNCTIONS
POWER ON / OFF
1
1. Push POWER button to on the power.
(Stand-by LED is OFF)
2. Push Power button again to off the power.
MODE
2
- It is a function to change video signal.
- The display is disappeared 6 sec. later after setting.
1. Push MODE button.
2. CAM1 or CAM2 or AV appears on the
screen it is disappeared after 6 sec.
MUTE
3
- This function can be operated by the remote control.
- This function works to MUTE sound instantly and display mute icon.
CONTRAST
BRIGHTNESS
COLOR
TINT
70
40
40
40
9
VOLUME CONTROL
4
VOLUME 30
1. Press VOL+/- (or VOL / ) button.
2. The monitor shows volume on the screen and volume is UP/DOWN.
AUTO PIC
5
When press the AUTO PIC button, PICTURE SETUP menu is displayed on screen.
RECALL
6
Press RECALL to check the MODE and Volume.
VOLUME 30
CAM1
PICTURE CAM1, 2SETUP
ENGLISH DEUTSCH ITALIANO FRANCAIS
ESPAnOL
한한한 한한한
DIMMER
LANGUAGE
DIRECTION
RESET
ENGLISH
0˚
2. Use button to select SUB MENU, use button to adjust.
SETUP
- DIMMER
- LANGUAGE
- DIRECTION
DIMMER
LANGUAGE
DIRECTION
RESET
ENGLISH
0˚
DIMMER
LANGUAGE
DIRECTION
RESET
ENGLISH
180˚
- RESET : A factory default reset will clear all of OSD information.
DIMMER
LANGUAGE
DIRECTION
RESET
ENGLISH
0˚
10
MENU
7
1. Use MENU button to change MAIN MENU, Changed
color in red when it is selected.
This button is for SETUP, PICTURE SETTING.
PICTURE
CONTRAST
BRIGHTNESS
COLOR
TINT
70
40
40
40
CAMERA(option)
CAM1 NORMAL
11
1. Use button to select CONTRAST, BRIGHT-
NESS, COLOR, TINT menu.
(Selected menu is in red.)
2. Press button and BAR and number are
changed and screen is adjusted.
(BAR sign is in red.)
Press button to select NORMAL / MIR-
ROR.
12
55” TFT LCD COLOR MONITOR
CONNECTIONS
CAMERA 1
CAMERA 2
DC 12V~24V
YELLOW(VIDEO 1)
WHITE(AUDIO 1)
BLACK(STAND BY1)
GREEN(STAND BY2)
CAMERA(OPTION)
CIGAR CABLE
- STAND BY1(Black, Priority) STAND BY(+) (for REAR VIEW)
* Connect this line to (+) of reverse light lamp.
- STAND BY2(Green) STAND BY(+) (for SIDE VIEW)
* Connect this line to (+) of side light lamp.
6
Monitor Cable Connection
Cable guidance use Normal connection
13
5” TFT LCD COLOR MONITOR
INSTALLATION
1. Choose a location where you install the monitor. Clean the place for the Stand with
cleaner and remove the protective tape. And then attach it exactly where you want.
2. Fasten the monitor with tapping screw.
3. Adjust angle of stand and install monitor.
4. Connect each connecting cable as in the product installation reference.
Cable guidance
Tapping screw
Safeguard tape
Control Knob (Angle)
Stand base
Fix Knob (Bracket)
7
1. Pull the battery cover to the direc-
tion of the arrow.
2. Place a battery with the (+) sign
upward. (No. CR2025)
3. Put the battery case back into the
remote control in the direction of
the arrow.
14
5” TFT LCD COLOR MONITOR
Changing REMOTE CONTROL Battery
8
15
5” TFT LCD COLOR MONITOR
SPECIFICATION
5 inch
QVGA (320x234)
400cd/m²
400:1
70˚ / 70˚ / 40˚ / 60˚
DC 12V ~ 24V
450mA (DC 12V, monitor set only)
AUTO (NTSC / PAL)
H : 15.734 kHz / V : 60 Hz
H : 15.625 kHz / V : 50 Hz
Composite Video 1Vp-p (75 ohm)
MONO INPUT 400 mVrms
0.5 Watt max.
7 languages
-10˚C ~ 60˚C
-20˚C ~ 70˚C
150(W) x 115(H) x 30(D) mm
400g (monitor only)
Screen size
Resolution
Brightness
Contrast ratio
View angle(L/R/U/D)
Voltage
Current
NTSC
PAL
Video Signal
Audio Signal
Input System
Speaker
Language display selection
Operating temperature
Storage temperature
Dimension
Weight
LCD Panel
Power Supply
Frequency
Input Signal
INSTRUCTION MANUAL
/
