Minka Group 924-695-L User manual

Brand: Minka Group

Model: 924-695-L

Type: User manual

Minka Group 924-695-L is a dimmable light fixture designed for indoor use. It is compatible with ELV and LED compatible wall dimmer switches, allowing you to adjust the brightness of the light to create the perfect ambiance for any occasion. The fixture's elegant design makes it a stylish addition to any room, complementing a variety of décor styles. Installation is relatively straightforward, requiring basic electrical knowledge and tools. With its versatility and ease of use, the Minka Group 924-695-L is a great choice for both residential and commercial lighting applications.

INSTALLATION INSTRUCTIONS

Item#924-695-L (New. 2023/02/20)

READ AND SAVE THESE INSTRUCTIONS

W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Fig. 1

Fig. 2

Fig. 3

MOUNTING THE FIXTURE (Fig.1)

Shut off power at the fuse box or circuit breaker box and remove

the old fixture including the mounting hardware.

2. Carefully unpack

your new fixture and lay out all the parts in a

clear area. Take care not to misplace any small parts necessary

for installation.

3. Loosening screws (D) to remove mounting plate (A) from

back

plate (C). Position mounting plate (A) on the wall and mark

the

location for two drywall anchors (F). Pre-drill the hole

s for

drywall anchors (F). Insert drywall anchors (F) into the wall.

4. Attach mounting plate (A) to the junction box (not included)

using mounting screws (B). The side of mounting plate (A)

marked “GND” must face out.

5. Screw wood screws (E)

through the holes into drywall anchor

(F) to secure mounting plate (A) as shown in Fig.1.

CONNECTING THE WIRES (Fig. 2)

Connect the electrical wires as shown in Fig. 2, making sure that

all wire connectors are secured

. If your junction box has a

ground wire (green or bare copper), connect the fixture’s ground

wire to it. Otherwise, connect the fixture’s ground wire directly to

the mounting plate (A

) using the green screw provided. After the

wires are connected, tuck them carefully inside the junction box.

FINISHING THE INSTALLATION (Fig.1)

7. Place back plate (C) over mounting plate (A) an

d secure with

screws (D).

Replacing LED module (Fig.3)

The LED module can be replaced by a qualified electrician

without cutting of wi

re and without damage to any decorative

element to which the fixture is attached. See installation steps

for more details (Fig 3.)

a. Shut off the power.

b. To remove fixture from the wall, loosen screws (D

) and back

plate (C) from mounting plate (A). Disconnec

t wire connectors

and place back plate (C) on a clean surface.

c. Loosening screws (G), remove white faux alabaster (N) from

back plate (C).

d. Loosening screws (I) using wrench (J) (included)

, remove

acrylic shade (M) from heating panel (H).

e. Press the button on pri

nted “L” quick connector on LED module

(K) with screwdriver (not included) to disconnect the black wire

Repeat by pressing the button on printed “N” quick connector

LED module (K) to disconnect the white wire.

f. Loosening screws (L)and remove LED module (K) from

back

plate (C).

g. Reverse steps b-f for installing the new LED module.

Note: Illustration (Fig. 1

) on this manual is for

installation purposes only. It may or may not be identical

to the fixture purchased.

Dimmable with ELV and/or LED compatible wall dimm

switches.

LA-3662E

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Green or

Bare

Copper

(Ground)

HOUSE

WIRES

Green

(Ground)

Set#A-021-118182

-Mounting Screw*2

-Ground Screw

-Mounting Plate

Screw Driver

Minka Group 924-695-L User manual

Minka Group 924-695-L User manual

Minka Group 924-695-L User manual

Related papers

Other documents