INSTRUCTIONS
Light Kit Bag #2
A4236
2
Introduction
Thank you for choosing Impact.
The Impact A4236 is a lightweight, sturdy, and durable case that
is ideal for any application where delicate and bulky lighting
equipment needs to be safely transported or stored.
This roomy bag has the capacity to t three monolight strobes and
reectors, as well as quartz or LED lights. The inner lid secures the
lights and provides enough space to hold up to four light stands
along with umbrellas, softboxes, or any gear you need to transport to
your shoot. Three large zippered mesh accessory pockets are ideal
for storing cables and organizing other gear or personal items.
A padded water-resistant nylon outer shell offers protection
from the elements and against bumps or impacts to your gear.
The interior of the bag is lined with a soft cotton tricot fabric
that will not scratch your equipment. It also rmly holds the
touch-fastener strips of the dividers and inner lid, assuring
that your equipment will not move during transport.
3
Dual handles are easily lengthened to convert into dual shoulder
straps. And the bottom of the bag features three rubber feet for added
protection when placing the bag on the ground. The bag folds down
to a quarter of its height for convenient storage and easy setup.
Precautions ⚠
• Please read and follow these instructions,
and keep this manual in a safe place.
• Clean the unit with a soft, dry cloth.
• Make sure the item is intact and that there are no missing parts.
• Excercise caution when using this product
with the maximum load capacity.
• All photos are for illustrative purposes only.
4
Overview
1
Light Kit Bag
2
Adjustable dual
handles/shoulder strap
3
Large internal
dividers (4)
4
Small internal
dividers (2)
5
Bottom panel
6
Inner lid
2
1
43
5
6
5
1. Open the bag and remove
all the contents.
2. Insert the bottom panel
so it lays at on the
bottom of the bag.
1
3. Insert the internal dividers
according to your needs. Press
the touch fastener strips on
the sides of the dividers to the
cotton interior lining of the bag
to hold them in position.
2
Note: It’s recommended
to space the large internal
dividers far enough apart so
they can support the inner lid.
21
Assembly Instructions
6
4. Place the inner lid over the
dividers and press the touch-
fastener strips to the sides of
the cotton interior lining.
3
5. Zip up the bag and adjust
the length of the handles as
needed. When fully extended,
the handles become a shoulder
strap.
4
Use the handle
wrap as a shoulder pad.
43
7
Specications
Specications
Outer shell material Water-resistant nylon
Interior lining material Cotton tricot
Type of closure Dual zippers
Folded dimensions (H × W × D) 3.5″ × 34.5″ × 13″ (9 × 87.6 × 33 cm)
Exterior dimensions (H × W × D) 14″ × 34.5″ × 13″ (35.6 × 87.6 × 33 cm)
Interior dimensions (H × W × D) 13.5″ × 34″ × 12″ (34.3 × 86.4 × 30.5 cm)
Carrying/transport options Dual 2″ wide strap handles with wrap that
convert to shoulder straps
Weight 5.75 lb. (2.6 kg)
One-Year Limited Warranty
This Impact product is warranted to the original purchaser to be free from defects
in materials and workmanship under normal consumer use for a period of one (1)
year from the original purchase date or thirty (30) days after replacement, whichever
occurs later. The warranty provider’s responsibility with respect to this limited
warranty shall be limited solely to repair or replacement, at the provider’s discretion,
of any product that fails during normal use of this product in its intended manner and
in its intended environment. Inoperability of the product or part(s) shall be determined
by the warranty provider. If the product has been discontinued, the warranty provider
reserves the right to replace it with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse, neglect, accident,
alteration, abuse, improper installation or maintenance. EXCEPT AS PROVIDED
HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES
NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This
warranty provides you with specific legal rights, and you may also have additional
rights that vary from state to state.
To obtain warranty coverage, contact the Impact Customer Service Department to
obtain a return merchandise authorization (“RMA”) number, and return the defective
product to Impact along with the RMA number and proof of purchase. Shipment of the
defective product is at the purchaser’s own risk and expense.
For more information or to arrange service, visit www.impactstudiolighting.com or call
Customer Service at 212-594-2353.
Product warranty is provided by the Gradus Group.
www.gradusgroup.com
Impact is a registered trademark of the Gradus Group. © 2015 Gradus Group LLC. All Rights Reserved.
GG1
/
