The Omega ODW707XB dishwasher offers efficient and convenient dishwashing with its 14 place settings capacity, dual zone wash function, and a variety of wash programs. Its intuitive control panel features a digital display, program selection buttons, and delay start option, allowing you to customize the wash cycle as per your needs. The machine ensures sparkling clean dishes with its powerful spray arms, efficient filtration system, and the use of rinse aid for spot-free drying.
The Omega ODW707XB dishwasher offers efficient and convenient dishwashing with its 14 place settings capacity, dual zone wash function, and a variety of wash programs. Its intuitive control panel features a digital display, program selection buttons, and delay start option, allowing you to customize the wash cycle as per your needs. The machine ensures sparkling clean dishes with its powerful spray arms, efficient filtration system, and the use of rinse aid for spot-free drying.
DWF8010
14 place settings
Alt function
www.fulgor.com.au
Witheachwashcycle.
Compartment
For programmes with pre-wash only.
(Follow the user instructions!)
Electric indicator on control panel (if provided).
Check the rinse aid level
Load the baskets
Select a programme
Running the dishwasher
Switch off the appliance
Turn off the water tap,
unload the baskets
Fill the detergent dispenser
Warning: wait a few minutes (about 15 minutes) before unloading the dishwasher to avoid handling
the dishes and utensils while they are still hot and more susceptible to break.
They will alsodry better.Unload the appliance, starting from the lower basket.
Changing theprogramme
Add forgotten dishes in the
dishwasher.
Scrape off any large amount of leftover food. Soften remnants of burnt food in pans,
then load the baskets. Refer to the dishwasher loading instructions.
When the working cycle has finished, the buzzer of the
dishwasher will sound 8 times, then stop.
Turn off the appliance using the On/Off Button.
If the appliance is switched
off during a wash cycle.
Open the door carefully.
Hotsteam may escape
when thedoorisopened!
If the appliance is switched off during a wash cycle, when switched
on again, please re-select the washing cycle and operate the dishwasher
according to the original Power-on state.
Switch on the appliance
For detailed operating method read the corresponding content onthe instruction manual.
Close the door, turn on the water tap. The machine will start working
after about 10 seconds.
Press the Programme Button, the selected programme indicator lights up.
( See the section entitled Operation instruction )“”
Open the door, press the On/Off button to switch on the appliance.
1. Arunning cycle can only be modified if it has been running for a short time. Otherwise the detergent
may have already been released and the water already drained. If this is the case, the detergent
dispenser must be refilled.
2. Open the door, press the program button more than 3 seconds, the machine will be in
standby state, then you can change the program to the desired cycle setting.
1.Open the door a little to stop the washing.
2.After the spray arms stop working, you can open the door
completely.
3.Add forgotten dishes.
4.Close the door, the dishwasher will run after 10 seconds.
To review the section on troubleshooting Tips
willhelp you tosolve some common problems
by yourself .
Dear Customer,
Please carefully readthismanualbefore usingthe
dishwasher,itwill help you to use and maintain the
dishwasher properly.
Pass it on toany subsequent owner of the appliance.
Thismanual contains sections on safety Instructions,
Operating Instructions, InstallationInstructionsand
Troubleshooting Tips, etc.
The manufacturer, following a policy of constant
development andupdating of the product, may
make modifications without giving prior notice.
Keep it as a refer in the later days.
If you can not solvethe problems by yourself ,
please ask forthe help of professional technicians.
This appliance is intended tobe used in household
andsimilar applications suchas:
-staff kitchen areas in shops, offices and other
working environments;
-farm houses;
-byclients inhotels,motels and otherresidential
type environments;
-bed and breakfast type environments.
Dishwasher Features.................................... ...2
AttentionbeforeorafterloadingtheDishwasher
Baskets..........................................................6
Filtering System.............................................11
Caring for the Dishwasher..................... .........12.
A Fill the RinseAidDispenser............. .. ..3、..... ...
B Function of Detergent .........................4、........
..............7
The Method Loading Normal Dishware
Wash CycleTable...........................................9
Turning on theAppliance................................9
Change the Programme.............. ................10....
At theEnd of the Wash Cycle...........................10
Positioning theAppliance................... ..........13..
Water Connection.................................. .......14.
AboutPowerConnection........................ .......13.
Startof dishwasher................................ ......15..
Before calling for service........................... .....16.
Errorcodes.................................... ..............17.
Technical information.............................. .....18..
Control Panel...................................................2
This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce
the risk of anelectric shock by providing a path of
least resistance of electric current. This appliance
is equipped with a cord having an equipment-
grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with
all local codes and ordinances.
When using your dishwasher, follow the precautions listed below:
Improper connection of the equipment-grounding
conductor can result in the risk of an electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded. Do not modify the
plug provided with the appliance; If it does not fit
the outlet. Have a proper outlet installed by a
qualified electrician.
Keep children away from detergent and rinse aid, keep
child away from the open door of the dishwasher,
there could still be some detergent left inside.
ren
Donotabuse,siton,orstandonthedoorordish
rack of the dishwasher.
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent. For plastic items
not so marked, check the manufacturer's
recommendations.
Use only detergent and rinse additives
designed for an automatic dishwasher.
Never use soap, laundry detergent, or hand
washing detergent in your dishwasher. Keep
these products out of the reach of children.
During installation, the power supply must not
be excessively or dangerously bent or flattened.
Do not tamper with controls.
Do not place any heavy objects the
door when it is open. The appliance could tip
forward.
on or stand on
When loading items to be washed:
1) Locate sharp items so that they are not likely
to damage the door seal;
2 Warning: Knives and other utensils with
sharp points must be loadedin the basket
with their points down orplaced in a
horizontal position.
)
Ifthesupplycordisdamaged, it must bereplaced
bythemanufactureroritsserviceagentora
similarly qualified person in order to avoid a
hazard.
Please dispose of packing materials properly.
Use the dishwasher only for its intended function.
Remove the door to the washing compartment when
removing an old dishwasher from service or discarding it.
Dishwasher detergents are strongly alkaline, they
can be extremely dangerousif swallowed.Avoid
contact with skin and eyes and keep children away
from the dishwasher when the door is open.
Check that the detergent comparment isempty
after completionof thewash cycle.
The applianceis to be connected to the water
mains using new hose sets and that old hose-sets
should not be reused.
The maximum number of place settings to be
washed is14.
The maximum permissible inlet water pressure is
1Mpa.
The minimum permissible inlet water pressure is
0.04Mpa.
Children should be supervised to ensure that they do
not play with the appliance.
This appliance is not intended for use by persons
(including children with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge ,unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
)
The door should not be left open,
since this could increase the riskof tripping.
Do not operate your dishwasher unless all
enclosure panels are properly in place. Open
the door very carefully if the dishwasher is
operating, there is a risk of water squirting out.
beforeusing it forthe first time.
To getthe best performance fromyour dishwasher, read all operating instructions
10 11
Back View
1
2
3
4
5
6
7
89
Front view
Lower basket
Dispenser
Cupshelf
Spray arms
Filter assembly
Inletpipeconnector
Drain pipe
Upperbasket
Cutlery rack
Top spray arm
1
Inner pipe
5
6
7
8
9
11
10
3
24
On/Off Button: To turn on/off the power supply.
Display screen: to show the remaining time
and the state(running state, delay time etc )
Program indicators:
RinseAid indicator:
Indicates whenthe dispenser needs to be refilled.
Delaytime ,Remain time,or error codes indicator:
Programstep indicators:
Delay Button : To Press the button to delay. Program Button : To Press the buttonto select
appropriate Program.
Alt function indicator:
Alt Button: Dual zone wash function, press the
button to select either upper basket or lower basket
loaded, and the response indicator .
Pre-washindicator:
Main-washindicator:
Rinseindicator:
Drying indicator:
Program end indicator:
Before using your dishwasher for the first time:
A. Fill therinse aiddispenser
B. Fill in detergent
Therinse aid isreleasedduringthe finalrinse to prevent water from forming dropletsonyour dishes, which can
leave spots and streaks. It also improvesdrying by allowing water to rolloff thedishes. Yourdishwasheris
designed to use liquidrinseaids.The rinseaid dispenser islocatedinside the door next to thedetergent dispenser.
To fill the dispenser,open thecapand pour the rinse aidinto thedispenser until the level indicatorturns completely
black.Thevolume ofthe rinseaidcontaineris about110ml.
RinseAid Dispenser
Function of RinseAid
Rinse aid is automatically addedduring the last rinse,ensuring thoroughrinsing, andspot and streakfree drying.
Attention!
Only use branded rinse aid for dishwasher. Never fill the rinseaiddispenser with any other substances
(e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.
As the rinse aid diminishes, the size ofthe black dot
on the rinse aid levelindicator changes, as illustrated below.
Full
3/4full
1/2full
1/4full-Shouldrefilltoeliminatespotting
Empty
If there is no rinse-aid warning light in the control panel, you can judge the amount of rinse-aid by the color of the
optical level
indicator "C" located next to the cap. When the rinse-aid container is full, the whole indicator will be dark .As the
rinse-aid
diminishes, the size of the dark dot decreases.You should never let the rinse aid get below 1/ 4 full.
When to Refill the RinseAid Dispenser
RINSEAID DISPENSER
To open the dispenser,turn the cap to the "open" (left) arrow and lift it out.
Pour therinse aid into the dispenser, being careful not to overfill.
Replacethe cap by inserting it alignedwith "open" arrow and turning it tothe closed (right) arrow.
Be careful not tooverfillthe dispenser, because this could cause over sudsing. Wipe away any spills
witha damp cloth. Don'tforget toreplace the cap beforeyou close dishwasher door.
Attention!
Clean up any rinse aid spill during filling with an absorbent cloth to avoid excess foaming
during the nextwash.
1
2
3
Adjusting RinseAid Dispenser
The rinse aid dispenser has six or four settings.Always start with the dispenser
set on "4". If spots and poor drying are a problem,increase the amount of rinse
aiddispensed by removing thedispenserlidandrotatingthedialto"5".Ifthe
dishes still are not drying properly or show spots,adjust the dial tothe next
higher lever until your dishes are spot-free. The recommended setting is "4".
(Factory value is "4".)
Increase the dose if there are drops of wateror limespots on the dishes after washing.
Reduce itif there are sticky whitish stains on your dishes or a bluish film on glassware or
knifeblades.
duringthenext wash.
Don't forget to replacethe cap before you close dishwasher door.
Cleanup any rinse aid spilled while duringfillingwithan absorbent cloth to avoid excessive foaming
Detergents with its chemical ingredients are necessary to remove dirt, crush dirt and transport it out ofthe dishwasher.
Most of the commercial quality detergents are suitable forthis purpose.
Detergents
There are 3 sorts of detergents
1.With phosphate and withchlorine
2.With phosphate and without chlorine
3.Without phosphate and without chlorine
Based on their chemicalcomposition, detergentscan be split in two basic types:
Theuse of normal washing programs in combination with concentrated detergents
reducespollutionand is goodforyour dishes;thesewashprograms are specificallymatched
to the dirt-dissolving properties of the enzymes of the concentrated detergent.For this reason
normal washprogramsinwhich concentrated detergents are used can achieve the same
results thatcan otherwise only be achieved using intensive programs.
“”
“”
“”
Detergent tablets of differentbrands dissolve at different speeds. For this reason some
detergent tabletscannot dissolve anddevelop their full cleaning power during short
programs. Therefore please use long programs when using detergent tablets, to
ensure the completeremovalof detergent residuals.
The dispenser must be refilled before the start of each wash cycle followingthe instructions
provided in the wash cycle table .Your dishwasheruses less detergent and rinse aid than
Conventional dishwasher. Generally, onlyone tablespoon of detergent is needed for
a normal wash load. More heavily soiled itemsneed more detergent.Alwaysaddthe
detergent just before starting thedishwasher, otherwise it couldget damp and will not
dissolve properly.
Concentrated Detergent
DetergentTablets
DetergentDispenser
conventional,alkaline detergents with caustic components
lowalkalineconcentrated detergents with natural enzymes
Normally new pulveriseddetergent is withoutphosphate.Thus the water softener function of
phosphate is not given. In this case we recommend tofill salt in the salt container even when
thehardness of water is only6 dH. Ifdetergents without phosphate are used in thecase ofhardwater
often whitespots appear ondishes and glasses. In this case please add more detergent to reach
better results. Detergents without chlorine doonlybleacha little. Strong and coloured spots will not
be removedcompletely.Inthiscase please choose aprogramwitha higher temperature.
°
AmountofDetergenttoUse
ProperUseofDetergent
Use only detergent specifically made for the usein dishwashers. Keep your detergent fresh and dry.
Don't put powdereddetergent into the dispenser until you're ready to wash dishes.
Dishwasher detergent is corrosive! Take care tokeepitout of reach of children.
Always add the detergentjustbefore starting each wash cycle.
Only use branded detergent aid for dishwasher.
If thelid is closed: press release button. The lid will spring open.
Detergent tablet
Detergent powder
Fill the detergentdispenser with detergent.
Themarkingindicatesthedosinglevels ,as
illustratedontheright:
The place of main wash cycle detergent placed.
The place of pre-wash cycle detergent placed.
Please observe the manufacturersdosing andstorage
Recommendations as stated on the detergent packaging.
Close the lid and press until itlocks inplace.
If thedishesare heavily soiled, placeanadditional
detergent dose in the pre-wash detergent chamber.This detergent will take effect during the pre-wash phase.
A
B
Fill in Detergent
You find information about the amount of detergent for the single programme on the last page.
Pleaseaware, that according to the levelsoiling andthe specifichardness of water differences are possible.
Pleaseobserve the manufacturer'srecommendations on the detergent packaging.
Cutlery withwooden, horn china or
mother-of-pearl handles
Plastic items that arenot heat resistant
Older cutlery with glued parts that are not
temperatureresistant
Bonded cutlery items or dishes
Pewter or cooper items
Crystal glass
Steel items subject to rusting
Wooden platters
Items madefromsyntheticfibres
Some types of glasses can become
dull aftera large number of washes
Silver and aluminum parts have a
tendencyto discolourduring washing
Glazed patterns may fadeif machine
washed frequently
Are not suitable Are oflimited suitability
Dishesand itemsofcutlerymustnotlie insideoneanother, orcover each other.
To avoiddamage to glasses, theymust not touch.
Load large itemswhich are most difficult to cleaninto the lower basket.
The upper basket isdesigned to holdmoredelicate and lighterdishware such as glasses, coffee
andteacups
Long bladed knives stored in an upright positionare a potential hazard!
Long and/or sharp items of cutlery such as carving knivesmust be positioned
horizontallyin the upper basket.
Please do not overload your dishwasher. This is important forgoodresults and for
reasonable consumption of energy.
Load hollow items such as cups, glasses, pans etc. With the opening facing downwardsso that
water cannot collect in the container or a deepbase.
Consider buying utensils which are identifiedasdishwasher-proof.
Usea mild detergentthatisdescribed as'kind todishes'. If necessary, seek further
information from the detergent manufacturers.
Forparticular items, select aprogramwithaslowa temperatureaspossible.
To prevent damage, do not take glassandcutlery out of the dishwasher immediately
after the programme has ended.
(For best performance of the dishwasher, follow these loading guidelines.
Features and appearance of baskets and cutlerybasketsmay vary from yourmodel.)
Scrape off any largeamounts ofleftover food. Soften remnants of burnt food inpans.
It is not necessary to rinse thedishes under running water.
Place objects in the dishwasher in following way:
1.Items such as cups, glasses, pots/pans, etc. are faced downwards.
2.Curved items, or ones with recesses, should be loaded aslant so that water can run off.
3.All utensils are stacked securely and can not tipover.
4.All utensils are placed in the way that the spray arms can rotate freely during washing.
Very small items should not be washed in the dishwasher as they could easily fall out of the basket.
To prevent water dripping from the upper basket into the lower basket, we recommend thatyou
empty the lower basket first and then the upper basket.
The upper basket is designed to hold more delicate
and lighter dishware such as glasses, coffee and
teacups and saucers, as well asplates,small bowls
andshallowpans (as long astheyare not too dirty).
Positionthedishes andcookwaresothatthey will
notgetmoved bythespray of water.
We suggest that you place large items and the most
difficulttocleanitemsareto be placedintothelower
basket: suchas pots, pans, lids, serving dishes and
bowls, as shown in the figure below. It is preferable to
place serving dishes and lids on the side of the racks
in order to avoid blocking the rotation of the top spray
arm.
Pots,servingbowls,etc,mustalwaysbeplacedtopdown.
Deep pots should be slanted to allow water to flow out.
Please bereminded that:
The Bottom Basket features folding spikes so that largeror more pots and pans can be loaded.
Folding Spikes of Lower Basket
For better stacking of pots and pans,
the spikescan be folded down as
show in the picture right.
Folding back the cup shelives
For better stacking of pots and pans,
the spikes can be folded down as
show in the picture right.
Cutleryshouldbe placed inthecutlery rackseparately
from each other in the appropriate positions, and do
make sure the utensils do not nest together,this may
causebadperformance.
For a top quality cleaning, place the silverware in the basket
makingsurethat:
They do not nest together.
Silverware is placed with the maleface up.
Long utensils in the middle.
Adjusting the Upper Basket
The height of the upper basket can be adjusted in order to
create more space for large utensilsboth for the upper
/lower basket. The height of the upper basket can be
adjusted by lift up the basket for the upper position, and up
press the handle to lower the upper basket, see the picture
below:
Position one: lift the left basket up, both left and right
baskets are slanting.
Position two: adjust the left basket to lower position, left
basket is flat and right basket is slanting.
Position three: lift the right basket up, both left and right
baskets are flat.
Position Four: Move the right basket from right to left, two
basket are overlapping.
Position Five: Remove the right basket from the tray,
only has the left basket.
Mode 1
Mode 2
Mode3
Mode 4
Mode 5
Cutlery basket has 5positions:
Normal
Intensive
Heavy
(OrAll )in1
5/27.5g
5
(OrAll )
/27.5g
in1
(OrAll )in1
5/27.5g
Pre-wash(50 )
Wash (65 )
Rinse
Rinse
Rinse(55 )
Drying
℃
℃
℃
Pre-wash(45 )
Wash (55 )
Rinse
Rinse (60 )
Drying
℃
℃
℃
Pre-wash
Wash (45 )
Rinse
Rinse(50 )
Drying
℃
℃
175
165
165
35
1.2
0.74
1.4
0.5
16.5
13.5
12.6
10
Pre-wash(50 )
Wash(60 )
Rinse (50 )
Drying
℃
℃
℃
60 9
0.85
5/27.5g
20g
Means:need to fill rinse into the Rinse-Aid Dispenser.
()
(*AS/NZS 2007.1)
For heavily soiled loads,
suchas pots, plates,glasses
and lightly soiled pans.
* : This program is the test cycle. The information for comparability test
in accordance with , as follows:
AS/NZS 2007.1
AS/NZS 2007.1
Capacity: 14 setting
Position Upper basket: upper wheels on rails
Rinse aid setting: 6
Open the door slightly 50mm to assist in drying of the dishes after every wash
Starting a cycle wash
1 Draw out the lowerandupper basket, load the dishes and pushthemback.
It is commended to load the lower basket first, then the upper one (see the section entitled
Loading the Dishwasher ).
2 Pour in the detergent (see the section entitled Detergent and RinseAid ).
3 Insert the plug intothe socket. The power supply is 220-240 VAC /50 HZ, thespecification
of thesocket is 10A 250VAC. Makesure that the water supply is turned on tofull pressure.
4 Openthe door, press the ON/OFF Button, and the display will turnon.
5 Press theprogramButton to selected your desired program.
If a program isselected, the response light will light.Then closethe door,the dishwasher begins
tostart.
“”
“”
Rapid
1Hour
Glass
For the heaviest soiled
loads, suchas pots, pans,
casserole dishesand dishes
thathavebeen sitting with
dried food on themfor a
while.
Standard dailycyclefor
normally soiled loads, such
aspots plates glasses.、、
For lightly soiled loads that
do not need excellent drying
efficiency.
Ashorterwashforlightly
soiledloads and quickwash.
For lightly soiled crockery
andglass
20g
Pre-wash
wash(40 )
Rinse
Rinse(60 )
Drying
℃
℃
115
0.85 13.5
Wash (40 )
Rinse
Rinse(45 )
℃
℃
When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then stop. Turn off
the appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher.
Wait for afew minutesbeforeunloading the dishwasher to avoidhandling the dishes and utensilswhile they
are still hot and more susceptible to breakage. Theywillalso dry better.
Switch Off the Dishwasher
The program light is on but is not blinking, only in this case the programme has ended.
1.Switch off the dishwasher by pressingthe ON/OFF button.
2.Turnoffthewatertap!
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down around 15 minutes
before removing from the appliance.
Open the dishwasher's door, leave it ajar and wait afew minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
Unloadingthedishwasher
It is normal that the dishwasher is wet inside.
Emptythelower basket first andthen the upperone.Thiswill avoid waterdrippingfromthe upper Basketonto
thedishesinthelowerone.
If you open the door during a wash cycle , the machine will pause. The program light will
stop blinking and the buzzer will mooing every minute unless you close the door. After
you close the door ,the machine will keep on working after 10 seconds.
Premise:
Acyclethat is underway can only bemodified if it has only been running fora shorttime.Otherwise, the
detergent may have already been released, and the appliance may have already drained the wash water.
If this isthe case,thedetergentdispenser must berefilled (see the sectionentitled "Loading the
Detergent").
Open the door , the machine will pause, press theprogram button more than
3s thenyoucan change theprogramto the desiredcycle setting (seethe section entitled " Startinga wash
cycle. .." ).
1
2
A forgotten dish can be added any time before the detergent cup opens.
Add forgotten dishes.
Close the door, the dishwasher will run
after 10 seconds.
After the spray arms stop working, you can open the door
completely.
2
3
Openthe door a little .
14
Wash the arms in soapy and warm water and use a soft brush to
clean thejets. Replace them after rinsing them thoroughly.
When following this procedure from step1 to step 3, the filter system will be removed;
when following it from Step 3 to Step 1, the filter system will be installed.
It is dangerous to open the door when washing,becausethe hot water may scald you.
The filter preventslarger remnants of food orother objects from getting inside thepump.
Theresidues may blockthe filter, inthis casethey must be removed.
The filter systemconsists of a coarse filter, a flat (Main filter)
Anda microfilter(Fine filter).
Food and soil particles trapped inthis filter arepulverizedby a
special jet on the lower spray arm andwashed down to drain.
Larger items, such as piecesof bonesor glass, that could block
the drainaretrappedin the coarse filter.To removetheitems
caught by the filter, gently squeeze the tap on thetop of this
filterandliftout.
Thisfilter holds soil and food residues inthe sumpareaand
prevents itfrom being redeposit on the dishes duringwash cycle.
Main filter
1
Coarse filter
2
Fine filter
3
2
3
1
Filter assembly
Thefilter efficiently
For best performance and results, the filter must be cleaned regularly. this reason, it is a good idea to
remove thelarger food particlestrappedin the filter after each washcycle by rinsing the semicircular filterand
cup under runningwater. To remove the filter device, pull the cup handle in the upward direction.
removes food particles from the wash water,allowing it to be recycled during the cycle.
For
The dishwasher must never be used without the filters.
Improper replacementof the filter may reduce the performancelevel ofthe appliance
and damage dishesand utensils.
Step 1 Turn the filter in anti-clockwisedirection,：
Step 2 lift the filter assy up：
When following this procedure from step1 to step 2, the filter system will be removed;
when following it from Step 2 to Step 1, the filter system will be installed.
1
2
The control panelcan be cleaned by using a lightly dampenedcloth.
Aftercleaning, make sure to dry it thoroughly.
For the exterior, use a good appliance polish wax.
Neveruse sharp objects, scouring pads orharsh cleaners onany part of the dishwasher.
ProtectAgainst Freezing
1.Cut off the electrical power to the dishwasher.
2.Turn off the water supply and disconnect the water inlet pipe from the water valve.
3.Drain the water from the inlet pipe and water valve. (Use a pan to gather the water)
4.Reconnect the water inlet pipe to the water valve.
5.Remove the filter at the bottomof the tub and use a spongeto soak up water in the sump.
please take frost protection measures onthe dishwasher in winter.Every fter washing cycles,
please operate as follows time a
：
Cleaning the Filter
Cleaning The Door
To clean the coarsefilter and the fine filter, use a cleaning brush. Reassemble the filter parts as shown in the figures
on thelast page and reinsert the entire assembly in the dishwasher, positioning it in itsseat and pressing downwards.
Whencleaning the filters, don't knock on them. Otherwise, the filters could be
contorted andtheperformance ofthe dishwashercouldbe decreased.
To clean theedge around thedoor, you should use only a soft warm, damp cloth.
To avoid penetrationof waterinto the door lock and electrical components, do not
use a spray cleaner of any kind.
Never usea spray cleaner to clean the door panel as it may damage the door lock
and electricalcomponents.
Abrasive agents or some paper towels shouldnot be used because of the riskof
scratching or leaving spots on the stainless steel surface.
Cleaning the SprayArms
If your dishwasher cannot work because of the ice,
please contact professional service persons.
It is necessary to clean the spray arms regularly for hard
waterchemicalswillclogthe sprayarmjetsandbearings.
- Inspect the filters for blockingafter every time the dishwasher has been used.
- By unscrewing the coarse filter, you can remove the filter system. Removeanyfoodremnants and
clean thefilters underrunningwater.
Remarks:
The entirefilter assembly shouldbe cleaned once a week.
To remove thelower spray arm, pullout the spray armupward.
To remove the upper spray arm, hold the nut, rotate the arm
clockwisetoremoveit.
Wash the arms in soapy and warm water and use a soft brush to
clean the jets. Replace them after rinsing them thoroughly.
Itisrecommendthatyourun awashcycle with the
dishwasher empty andthen remove the plug from the
socket, turn off the water supply and leave the door of
the appliance slightly open. This will help the door
sealstolastlonger andpreventodoursfromforming
withintheappliance.
If the appliance must be moved, tryto keep it in the
verticalposition.Ifabsolutelynecessary, itcanbe
positioned on its back.
Oneofthefactorsthatcauseodourstoforminthe
dishwasher is food that remains trappedin the seals.
Periodic cleaning with adamp sponge will prevent this
from occurring.
Ensure the voltage and frequencyof the power being correspondsto
those on the rating plate. Only insert the plug into an electricalsocketwhich is earthed
properly. If the electrical socket to which the appliance must be connected is not
appropriate fortheplug, replace the socket, ratherthan usingaadaptors or the likeas
they couldcause overheatingandburns.
Pleaselook at therating label to know the rating voltage and connect the dishwasher to the appropriate powersupply.
Use the required fuse 10 amp,timedelay fuse or circuitbreaker recommended and provide separate circuit serving
only this appliance.
Position the appliance in the desired location.The back should rest against thewall behind it, and the sides,
along the adjacent cabinets or walls.The dishwasher is equippedwith water supply and drain hoses that can
be positioned either to the rightor the left sides to facilitateproper installation.
Once the appliance is positionedfor levelling, the height of the dishwasher
may be altered viaadjustment of the screwing level of the feet. In any case,
theappliance should not be inclined more than 2 .
For personal safety:
DO NOT USEAN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDERANY CIRCUMSTANCES, CUT OR REMOVE THE EARTHING
CONNECTION FROM THE POWER CORD.
Before cleaning or performing maintenance, always
remove the plug from the socket.
Tocleantheexteriorandrubberparts ofthedishwasher,
donot use solventsor abrasivecleaningproducts.
Only use acloth with warm soapy water.
To remove spots or stains from the surface of the
interior, use a cloth dampened withwater ana little
vinegar, or a cleaning product madespecificallyfor
dishwashers.
Remove the Plug
No Solvents orAbrasive Cleaning Moving theAppliance
Seals
After every wash, turn off the water supply to the
appliance and leave the doorslightlyopen sothat
moisture and odours arenot trapped inside.
After Every Wash
When not in Use for aLongTime
This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of
electric shock by providing a path of least resistance for the electric current. This appliance is equipped with a
cord having an equipment-earthing conductor and an earthing plug. The plug must be plugged into an
appropriate outlet that is installed and earthed in accordance with all local standards and requirements.
for personal safety:
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE
FROM THE POWER CORD. EARTHING
CONNECTION
Improper connection of the equipment earthing conductor can result in the risk of an
electric shock.
Check with a qualified electrician or service representative if you are in doubt whether the
appliance is properly earthed.
Do not modify the plug provided with the appliance. If the plug does not fit properly to the
outlet, please have a qualified electrician to install a proper outlet.
Ahose that attaches toa sink spray canburst if it is installed on the samewater line as thedishwasher. If your sink
has one, it is recommendedthat the hose be disconnected and the hole plugged.
Pull The safety supply hoses completely out from storage compartment located at rear of dishwasher.
Turn water fully on before starting the dishwasher.
1
Tighter the screws of the safety supply hose to the faucet with thread 3/4inch.
The safety supply hose consists of the double walls. The hose's system guarantees its intervention by blocking the
flow of water in case of the supply hose breaking and when the air space between the supply hose itself and theouter
corrugated hose is full of water.
Turn off the water.
Release thewater pressure by depressing the pressure release button. This relieves water pressure and protects you, and the
room, from severe splashing.
Unscrew the safety supply hose from the faucet.
3
2
1
2
3
The appliance must be connected to the water mains using new hose-sets.
The old hose-sets should not be reused.
Waterpressure must be between 0,04 MPa and 1 MPa. If thepressure is below the
minimum consult our Service Department for advice.
Connect the cold water supply hose to athreaded3/4(inch) connectorand make sure that it is fastened tightlyin place.
Ifthewater pipes are new or have not been used for anextended period oftime, let the water runto makesurethat the
wateris clear and free of impurities. If this precaution is not taken, there is arisk thatthe water inlet can get blocked
and damage the appliance.
MAX 1000mm
A
Counter
Front
Drain pipe
NOTE
The top of the hose
must be less than
1000mm.
40mm
B
PLEASE HANG UP THE DRAIN HOSE EITHER WAY OF A, BPLEASE HANG UP THE DRAIN HOSE EITHER WAY OF A, B
1515
Start of Dishwasher Start of Dishwasher
The content of this manual is very helpful to the users.
After installation, please make sure to keep this manual.
Attention:Attention:
Extension Hose
If you need a drain hose extension, make sure to use a similar drain hose.
It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be reduced.
Water Outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
Ensure that the water drain hose is not kinked or squashed.
If the sink is 1000 higher from the floor, the excess water in hoses cannot be drained directly
into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable
container that is held outside and lower than the sink.
How to Drain Excess Water From Hoses
Syphon Connection
The waste connection must be at a height less than 1000 mm (maximum) from the bottom of the dish.
The water drain hose should be fixed .
Drain hose Connection
Insert the drain hose into a drain pipe with a minimum diameter of 40mm, or let it run into the sink, making sure to
avoid bending or crimping it. The top of the hose must be less than 1000mm.
The following things should be checked before starting the dishwasher.
1 The dishwasher is level and fixed properly
2 The inlet valve is open
3 The power plug is correctly plugged in
4 The power is switched on
5 The inlet and drain hoses are connected
6 All packing materials and printings should be taken out from the dishwasher
Fuse blown, or the
circuit breaker tripped Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Spilled rinse-aid Always wipe up rinse-aid spills immediately.
Hard water minerals
The affected items are
not corrosion resistant.
The lid of the softer
is loose
Aspayarmis
knocking against
an item in a basket
r
Items of crockery
are loose in the
wash cabinet
This may be caused
by on-site installation
or the cross-section of
the piping.
A programme was not
run after dishwasher
salt was added.
Traces of salt have
gotten into the wash cycle.
To clean the interior, use a damp sponge with
dishwasher detergent and wear rubber gloves.
Never use any other cleaner than dishwasher
detergent for the risk of foaming or suds.
Always run the quick wash programme .
without any crockery in the dishwasher and
without selecting the Turbo function (if present),
after adding dishwasher salt.
Check the lid .Ensure it is correctly closed.
Interrupt the programme, and rearrange the items
which are obstructing the sp ay arm.r
Interrupt the programme,
and rearrange the items of crockery.
This has no influence on the dishwasher function.
if in doubt, contact a suitably qualified plumber.
Detergent with
colourant was used Make sure that the detergent is the one without
colourant.
Improper detergent
Make sure the dishwasher is turned on and the door is
closed securely.
Check that the water supply is connected properly and
the water is turned on.
Make sure to close the door properly and latch it.
Make sure the power cord is properly plugged into the
wall socket.
Power supply is not
turned on
Error code:E1;
Water pressure is low
Door of dishwasher
not properly closed.
Kink in drain hose
Filter clogged
Kitchen sink clogged
Check drain hose.
Check coarse the filter
(see section titled )" Cleaning The Filter "
Check the kitchen sink to make sure it is draining well.
If the problem is the kitchen sink not draining ,you may
need a plumber rather than a serviceman for dishwashers.
Use only the special dishwasher detergent to avoid suds.
If this occurs, open the dishwasher and let suds evaporate.
Add 4 litresof cold water to the tub. Close and latch the
dishwasher, then select anycycle. Dishwasher willdrain
outthe water at the first step. Open the door after draining
is stop and check if the suds have disappeared.
Repeat if necessary.
The dishes were not
loaded correctly. See notes in " Loading the Dishwasher Baskets ".
Select a more intensive programme.
See" Wash Cycle Table ."
Use more detergent, or change your detergent.
Rearrange the items so that the sp ay arm can rotate
freely. r
Clean and/or fit the filter combination correctly.
Clean the sp ay arm jets. See "Cleaning the Spray
Arms". r
Use less detergent if you have soft water and select
a shortest cycle to wash the glassware and to get
them clean.
Use a mild abrasive cleaner to eliminate those marks.
Re-loading the dishes properly.
Load the dishwasher as suggested in the directions.
Increase the amount of rinse-aid/refill the rinse-aid
dispenser.
Do not empty your dishwasher immediately after
washing. Open the door slightly so that the steam can
escape. Begin unloading the dishwasher only once t
he dishes are barely warm to the touch. Empty the low
basket first. This prevents water form dropping off
dishes in the upper basket.
In short program the washing temperature is lower.
This also lowers cleaning performance. Choose
a program with a long washing time.
Water drainage is more difficult with these items.
Cutlery or dishes of this type are not suitable for
washing in the dishwasher.
The programme was
not powerful enough.
Not enough detergent
was dispensed.
Items are blocking
the path of sp ay arms.r
The filter combination
inthebaseofwash
cabinet is not clean or
is not correctly fitted.
This may cause
the sp ay arm jets
to get blocked.
r
Combination of soft
water and too much
detergent.
Aluminum utensils
have rubbed against
dishes.
Dishes block
detergent cups.
Improper loading
Too little rinse-aid
Dishes are removed
too soon
Wrong program
has been selected
Use of cutlery with
a low-quality coating
Overflow.
When some malfunctions come on, the appliance will display error codes to warn you:
Longer inlet time.
Faucets is not opened, or water intake is
restricted,or water pressure is too low.
Some element of dishwasher leaks .
E4
E1
E8
Open circuit or break of distributary valve.
Failure of orientation of distributary valve.
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
The Omega ODW707XB dishwasher offers efficient and convenient dishwashing with its 14 place settings capacity, dual zone wash function, and a variety of wash programs. Its intuitive control panel features a digital display, program selection buttons, and delay start option, allowing you to customize the wash cycle as per your needs. The machine ensures sparkling clean dishes with its powerful spray arms, efficient filtration system, and the use of rinse aid for spot-free drying.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Technika Dishwasher User manual
-
Venini VDW60S User manual
-
Comfee Storm Freestanding Dishwasher 60cm User guide
-
BLANCO BDW1465X User manual
-
Brandt DFH13117X User manual
-
DeLonghi DEDW654FI Quick start guide
-
Whirlpool ADP 650 Operating instructions
-
Midea WQP12-5201C User manual
-
-
