Gfp 230 C Operating instructions
- Category
- Laminators
- Type
- Operating instructions
Gfp
2
30
C
June
2012
1
OPERATING MANUAL Gfp 230 C
Please read this manual carefully before operating!
Unpacking, assembly, and operating videos are available at
www.gfpsmoothstart.com
Gfp
2
30
C
June
2012
2
Table of Contents
Contents Page
1. Introduction …………………………………………………… 3
2. Important Safety Instructions………………………………….. 3
3. Installation Safeguards ……………………………………….. 4
4. General Safeguards……………………………………………. 5
5. Operating Conditions …………………………………………. 6
6. System Components ………………………………………….. 7
7. Control Panel …………………………………………………. 8
8. Packing List ………………………………………………… .. 9
9. Installation
A. Uncrate the machine……………………………………. 10
B. Remove cross members and machine from Skid……… . 11
C. Assemble machine stand……………………………….. 12
D. Set Machine on stand…………………………………... 12
E. Attach supply support brackets………………………… 13
10. Additional installation items …………………………………. 14
11. Loading bottom Media or Kraft Paper rolls ………………….. 14
12. Installing take up reel…………………………………………. 15
13. Loading Film………………………………………………….. 16
14. Threading Film ……………………………………………….. 17
15. Operation ……………………………………………………... 18
16. Roller Gap………….. ………………………………………… 18
17. Laminating
A. Single sheets using a sled………………………………. 19
B. Multiple sheets using a roll of Kraft Paper……………... 20
C. Media from a roll……………………………………….. 20
18. Mounting
A. Pre-coating mounting boards…………………………… 21
B. Mounting print to pre-coated mounting boards………… 21
19. Troubleshooting ………………………………………………. 22
20. Specifications …………………………………………………. 23
21. Warranty ………………………………………………………. 24
Gfp
2
30
C
June
2012
3
1. Introduction
Thank you for choosing a Gfp laminator. It has been designed and manufactured to
provide years of continuous service. Please read this manual thoroughly before
operating. Please inspect the box and the laminator for shipping damage. Damage
should be brought to the attention of the delivering carrier immediately. For a list of
shipping components see “Packing List” on page 9.
2. Important Safety Instructions
In this operating manual you will find important safety messages regarding the product.
Read these instructions carefully, failure to comply with the following safety
procedures could result in serious injury.
WAR$I$G Do not attempt to service or repair the laminator. Only
authorized maintenance and service technicians should make repairs.
WAR$I$G Do not connect the laminator to an electrical supply or attempt
to operate the laminator until you have completely read these instructions.
Maintain these instructions in a convenient location for future reference.
WAR$I$G To guard against injury, the following safety precautions must
be observed in the installation and use of the laminator
Gfp
2
30
C
June
2012
4
3.
Installation Safeguards
• Shipping damage should be brought to the immediate attention of the
delivering carrier
• Avoid locating the laminator near sources of heat or cold. Avoid locating the
laminator in the direct path of forced, heated or cooled air
• The receptacle must be located near the equipment and easily accessible.
• Connect the attachment plug provided with the laminator to a suitably
grounded outlet only. This machine must have reliable earth wire to ensure
the safety of the machine during operations
• Contact an electrician should the attachment plug provided with the laminator
not match the receptacles at your location
• Ensure that the voltages of the power supply you are using match the
rated working voltages before operations. Do not use incorrect power supply
• Do not use damaged wires or sockets. If abnormal conditions occur,
switch off the power supply first.
• Only a licensed electrician should install wiring and outlet for the
laminator
• Do not defeat or remove electrical and mechanical safety equipment such as
interlocks, shields and guards
Gfp
2
30
C
June
2012
5
4. General Safeguards
• Keep hands, long hair, loose clothing, and articles such as neckties away from
rollers to avoid entanglement and entrapment. The rollers have pinch points
that can trap body parts or clothing and cause serious injury
• Do not use the machines for purposes other than lamination and mounting,
otherwise damages to the machine or accidents may occur
• Keep out of reach of children
• Keep flammable and wet objects away from the machine.
• Do not use flammable sprays or materials when cleaning the machine
• Do not leave the machine unattended during operations.
• Do not mount metal materials or other hard objects.
• Do not put burrs, sharp blade or rigid materials in between the two rubber
rollers.
• Do not attempt to laminate items that exceed total recommended material
thickness of the unit.
• Do not place foreign object inside the machine.
• Do not cut adhesive films directly on the surface of the rollers to avoid
damaging the rubber coating.
• Shut down the machine after laminating to avoid misusing this machine by
others.
• Shut down the power before moving the machine
• Note the locations of foot wheels while moving or operating this machine to
avoid injuries to your feet.
• Disconnect from the power supply before repair or maintenance.
• Disconnect from the power supply when the machine is not in use for
a long time.
• When the machine lies idle for a long period of time, raise the top rubber
roller to avoid the distortion of the rubber surface.
• Perform only the routine maintenance procedures referred to in these
instructions
Gfp
2
30
C
June
2012
6
5. Operating Conditions
• Place machine on level surface
• Environment requirements：
Ambient temperature: 50⁰ F - 104⁰ F
Humidity：30%—80%；ideal humidity：55%
• Due to the static on film rolls, you should try to keep the environment clean.
• Provide enough space around machine to ensure the safe and effective operation.
The minimum area covered is 8 ft. x 10 ft.
• Do not directly cut the films on the surfaces of the rubber rollers to avoid
damages to the rollers.
• Do not put burrs, sharp knives or extra thick and hard materials in between the
rollers. Do not leave objects like tools, rulers, knives, etc on the working panels
or the side cabinets to avoid their being rolled into the machine accidentally and
damaging the rollers.
• For repairs and replacements, please contact your local distributor. Unauthorized
repairs and dismantling will affect future maintenances of the machines.
• The machine can laminate continuously objects less than ½” thick.
For objects over ½” but less than 1” thick, use the pedal switch.
Warning: Do not keep the machines in direct sunshine or near it.
Do not keep the machine in dusty place or places with strong vibrations.
Gfp
2
30
C
June
2012
7
6. System Components
1. Bottom supply shaft 11. Liner rewind
2. Front Support beam 12. Top Film supply shaft
3. Brake assembly 13. Brake assembly
4. Feed tray 14. Right side frame
5. Nip safety guard 15. Roller pressure adjustment
6. Left side frame 16. Power cord
7. Emergency stop switch 17. Control panel
8. Top nip roller 18. Bottom roller support bracket
9. Roller pressure linkage shaft 19. Foot switch
10. Rear exit deck
Gfp
2
30
C
June
2012
8
7. Control Panel
1. Run/ foot pedal switch 2. Speed Adjustment 3. Forward/ reverse switch
$ote: The machine does not have continuous reverse.
Reverse can only operate using the pedal switch
.
2
1
3
Gfp
2
30
C
June
2012
9
8.Packing List
Remove all parts from shipping create and boxes. Inspect parts and the machine
carefully. Any missing parts should be reported to the shipper upon receipt of
shipment.
Main Machine Crate
Part Quantity Part Quantity
Main Machine 1 Hex Screw 8mm x 80 8
Rewind tube 1 Hex Screw 5mm x 12 16
Support brackets for shafts 4 Plain washer #8 8
Supply shafts 2 Plain washer #5 16
Brake assembly 4 Lock washer #8 8
Stand legs 2 Lock washer #5 16
Stand cross members 2 Zippy knife 1
Allen wrench 6mm 1 Foot switch 1
Allen wrench 5mm 1 Operators manual 1
Allen wrench 4mm 1
Allen wrench 3mm 1
Gfp
2
30
C
June
2012
10
9. Installation
A. Uncrate the machine
1. Remove screws around the base of the crate including corner
supports
2. Lift crate straight up and off the skid
3. Stand legs are inside behind the machine
Gfp
2
30
C
June
2012
11
9. B. Remove cross members and machine from skid
1. Remove plastic cover and accessory box.
2. Remove supply shafts and stand cross members from the crate base by
loosening the screws and hold down straps
3. Remove four (4) anchor bolts holding machine to shipping skid
Supply shafts
Stand cross members
Anchor bolts
Gfp
2
30
C
June
2012
12
9. C. Assemble machine stand
1. Bolt cross members to stand legs using 8- 8mm x80 screws
2. Each screw takes a flat washer and lock washer – Flat washer against
the stand.
3. Start all screws by hand before tightening
9. D. Set machine on stand
1. Remove machine from the bottom supports of the shipping crate
2. Lift machine onto support stand
Heavy! Handle with care!!
Warning: when moving the machine, lift by side frames. Do not use roller gap adjustment hand-
wheel for lifting!
Gfp
2
30
C
June
2012
13
9 E. Attach bottom supply brackets and insert supply shaft
1. Attach Top and Bottom supply brackets to each side frame using
16- 5mm x12 screws
2. Slide brakes on round supply shafts
3. Insert supply shafts onto top and bottom supply brackets
1. Upper supply shaft 3. Supply shaft bracket
2. 5mm x12 hex screws 4. Foot switch
Gfp
2
30
C
June
2012
14
10. Additional Installation items
1. Plug foot pedal into rear panel near power cord
2. Check drive chains for tightness
3. Check all drive set screws for tightness
4. Check all electrical connections and input power and test for proper operation
11. Loading Bottom media or Kraft paper roll
1. Loosen the fastening screws on the brake assembly on one side of the supply
shaft, and slide brake assembly off the supply shaft.
2. Slide the new roll onto the supply shaft
3. Return the brake assembly to the supply shaft
4. Position the supply roll in the middle of the supply shaft and measure the
distance from one side of the roll to the side frame (You’ll use this
measurement when loading the top supply roll in section #13 to align the top
and bottom rolls)
5. Fasten the screws for brake assembly (Note: there should be 1/8” clearance
between the positioning and the adjusting sleeves of the film core adaptor to
make brake adjustment easier)
6. Adjust the brake tension by turning the adjusting sleeve
(Note: the brake tension should not prevent roll from turning)
1. Supply shaft 2. Substrate 3.Film Core 4. Positioning sleeve
5. Brake adjustment screw 6.Fastening screws for the brake assembly 7. Brake assembly
Gfp
2
30
C
June
2012
15
12. Installing Take up reel
1. Loosen the pressure-adjusting nut near the right cabinet, and the rewind
tube can then be removed from the machine
2. Slide a cardboard tube onto the rewind tube by rotating away from the core
stop clip
3. Install the rewind tube onto the positioning sleeves with the core stop clip
pointing away from the Nip Rollers or toward rear of the machine with
core stop clip positioned on top of the rewind tube. (Note: Pay attention
to the direction of the core stop clip, or the application will be affected.)
4. The rewind tube is driven by friction. The friction and tension will be
increased with a left turn of the pressure-adjusting nut, and a right turn will
decrease them.
$ote:
Adjust the rewind tube pressure-adjustment nut to allow the
backing paper to be removed and the film to enter the rollers evenly
1. Cardboard tube 2. Core Stop clip 3. Rewind Tube 4. Left side cabinet
5. Positioning sleeve 6. Positioning sleeve 7. Pressure-adjusting nut 8. Right side cabinet
Gfp
2
30
C
June
2012
16
13. Loading Film
1. Loosen the fastening screws on the film core adaptor on one side of the supply
shaft, and slide off the supply shaft.
2. Slide the film rolls onto the supply shaft
3. Return the film core adaptor to the supply shaft
4. Position the film in the middle of the supply shaft and measure the distance
from one side of the film core adaptor to the side frame ( Position the same
distance from the roll to the side frame as the bottom roll in section #11 to
align the top and bottom rolls)
5. Fasten the screws for film core adaptor (Note: there should be 1/8” clearance
between the positioning and the adjusting sleeves of the film core adaptor to
make brake adjustment easier),
6. Adjust the brake tension by turning the adjusting sleeve (Note: the brake
tension should not prevent roll from turning)
7. Position bottom roll same distance from side frame as the top supply roll
1. Supply shaft 2. Substrate 3.Film Core 4. Positioning sleeve
5. Brake adjustment screw 6.Fastening screws for the brake assembly 7. Brake assembly
Gfp
2
30
C
June
2012
17
14. Threading Film
1. Place cold film roll on top supply shaft and mounting adhesive roll on bottom.
( See “Loading film” section 13)
2. Pull the film with the paper liner by hand, making sure there is proper
resistance. The resistance can be adjusted with the adjusting sleeves near the
core chucks on each side of the supply shaft
3. Turn the pressure-adjusting hand-wheel to lift up the upper rubber roller.
4. Pass the film through the two rollers and lay on the rear working panel. Pull the
film flat then turn the pressure-adjusting hand-wheel to let down the upper
rubber roller.
5. Separate the paper liner from the film web at an appropriate place, pull up the
liner and tape it to the paper tube on the top rewind tube
$OTE: Slide film cutter between the paper liner and film to cut liner only.
Be careful not to cut the top heat roller
6. Use foot pedal to advance the film web until the adhesive is exposed on the
front of the top nip roller
7. Raise the feed tray assembly
8. Bring the bottom mounting adhesive or media web up and tack to the exposed
film web adhesive
9. Lower the feed tray assembly
10. Use foot pedal to advance both webs until cleared of the nip rollers
$ote: The film should be wrinkleless and tight to the surface of the heat
roller. If the film is not tight enough, turn increase the roller pressure. If
wrinkles appear in the film web, adjust the brake tension on both sides of
the film roll
1. Bottom Supply roll
2. Feed Tray
3. Top Nip roller
4. Pressure linkage shaft
5. Liner Rewind
6. Liner
7. Film supply roll
8. Film web
9. Bottom Nip roller
10. Media or Kraft paper web
Gfp
2
30
C
June
2012
18
15. Operation
1. Plug power cord into a proper receptacle
• Connect the attachment plug provided with the laminator to a suitably
grounded outlet only. This machine must have reliable earth wire to ensure
the safety of the machine during operations
• Contact an electrician should the attachment plug provided with the laminator
not match the receptacles at your location
• Ensure that the voltages of the power supply you are using match the rated
working voltages before operations. Do not use incorrect power supply
• Do not use damaged wires or sockets. If abnormal conditions occur, switch
off the power supply first.
2. Turn power to “ON” with the rear power switch
16. Roller Gap
1. When the pressure-adjusting hand-wheel is turned clockwise, the top rubber
roller comes down and the pressure will increase
2. With a counter-clock turn, the top rubber roller goes up and the pressure will
decrease.
3. Too much nip pressure will wrinkle the output. Bring the nip roller down to
just touch the film, then a slight increase in pressure
4. When using the 230C, bring the rollers down only to touch the film together.
Pressure
hand wheel
Gfp
2
30
C
June
2012
19
17. Laminating
$ote: It is hard to remove film adhesive once it gets onto the rubber
rollers. When laminating, always use materials same width as the film
roll. If your sheets are narrower than the film roll, use a laminating sled
or Kraft paper roll on the bottom to keep the film adhesive from sticking
to the bottom machine rubber roller. Always use media roll the same
width or wider than the film supply roll.
To clean the rollers, use rubber eraser or Isopropyl Alcohol and a shop
towel.
17. A Single Sheets using a sled
• Load a roll of laminating film on the top roller
( see loading film section 13)
• Turn the pressure-adjusting hand-wheel to lift up the upper roller.
• Select a piece of Gatorboard or other PVC mounting board the width
of the film web to use as a sled under the print to be laminated
• Insert the sled between the nip rollers and lower the top roller until it
touches the sled
• Reverse the motor to back the sled out of the rollers
• Pass the film web under the idler bar and down in front of the roller
• Separate 1” of the paper liner from the film web, attach film web to
a leader board the width of the film roll and insert leader board into
the rollers
• Use foot pedal to advance the film web half way through the roller
and stop
• Position print on the sled
• Depress the foot switch and run sled through
• Insert another leader board or next sled right behind the first sled
Gfp
2
30
C
June
2012
20
17 B. Multiple sheets using Kraft paper from all roll
• Load a roll of laminating film on the top unwind Supply Shaft
( see Loading film section 13)
• Load a roll of Kraft Paper on the bottom, front unwind Supply shaft,
unwinding from the BOTTOM of the roll
• Thread both rolls through machine ( see Threading film section 13)
• Press run
• Feed single sheets continuously
17 C. Media from a roll
• Load a roll of laminating film on the top unwind Supply Shaft
( see Loading film section 13)
• Load a roll of printed media on the bottom, front unwind Supply shaft,
unwinding from the TOP of the roll
• Thread both rolls through machine ( see Threading film section 13)
• Press run
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Gfp 230 C Operating instructions
- Category
- Laminators
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
