JBL MS-A5001 Datasheet

JBL
Brand
JBL
Model
MS-A5001
Category
Audio amplifiers
Type
Datasheet

JBL MS-A5001 is a great choice for anyone looking to add some serious bass to their car audio system. With 500 watts of power, it can easily drive even the most demanding subwoofers. It also has a variety of features that make it easy to customize the sound to your liking, including a digital input mixer, sophisticated network circuitry, and onboard setup tools.

Here are some of the things you can do with the JBL MS-A5001:

  • Connect up to two subwoofers in parallel
  • Accept any line-level or speaker-level output
  • Easily set up the crossover points and slopes
  • Adjust the input sensitivity and gain

JBL MS-A5001 is a great choice for anyone looking to add some serious bass to their car audio system. With 500 watts of power, it can easily drive even the most demanding subwoofers. It also has a variety of features that make it easy to customize the sound to your liking, including a digital input mixer, sophisticated network circuitry, and onboard setup tools.

Here are some of the things you can do with the JBL MS-A5001:

  • Connect up to two subwoofers in parallel
  • Accept any line-level or speaker-level output
  • Easily set up the crossover points and slopes
  • Adjust the input sensitivity and gain
There’s nothing like a subwoofer or two for adding major bass kick to any factory sound system. The JBL
®
MS-A5001 is
a compact amplifier with 500 watts of power and outputs to connect up to two subwoofers in parallel. It accepts any
line-level or speaker-level output, and features onboard setup tools for easy, foolproof installation. A digital input mixer
lets you map your inputs to either output, and sophisticated network circuitry puts you in precise control of the crossover
points and slopes. Serious bass is an essential element of any great car audio system, and the MS-A5001 delivers it
with easy precision.
SPECIFICATIONS
Manufacturer: HARMAN International Industries, Incorporated
Model: MS-A5001
Power output (CEA 2006): 500W RMS x 1 @ 4 ohms
500W RMS x 1 @ 2 ohms
Frequency response: 20Hz – 270Hz
Signal-to-noise ratio: >80dB (1W)
>106dB (full power)
Maximum input sensitivity: 100mV
Maximum input voltage: 20V
Power requirement: 12V DC, negative ground
Main unit dimensions (L x W x H): 7-3/16" x 8-1/4" x 2-3/4" (183mm x 210mm x 70mm)
Weight: Approximately 5.2 lbs (2.5kg)
MS-A5001
Digital signal processing amplier
HARMAN Consumer, Inc.
8500 Balboa Blvd., Northridge, CA 91329 USA www.jbl.com
© 2010 HARMAN International Industries, Incorporated. All rights reserved. JBL is a trademark of HARMAN International Industries, Incorporated, registered in the United
States and/or other countries.
Features, specifications and appearance are subject to change without notice.
HIGHLIGHTS
Mono subwoofer power amplifier – 500 watts x 1 @ 4 ohms; 500 watts x 1 @ 2 ohms
Connects to any analog signal – RCA to bare-wire adapters work with all line-level and speaker-level
inputs; selector switch for matching input to signal type; Hi2 setting for use with audio systems that
detect amp connections
Graphical setup/status display – Icons of crossover types and numeric readout of direct frequencies
simplify setup
Digital input mixer – Simplifies configuration by allowing any input signal to be routed to either
speaker output
Rotary encoder controls
FEATURES
Digital signal processing – Extremely precise control of all input mixer, electronic crossover and
output levels with a minimum of audible artifacts
Extremely sophisticated crossover functions – Outputs can be set to low-pass, high-pass or band-
pass filtered, with 97 different crossover points between 20Hz and 140Hz; independent crossover
slopes for each output-channel pair can be chosen from 6dB, 12dB or 24dB per-octave rates
Dual speaker outputs accept up to 10AWG wire – Easily connect two subwoofers in parallel with
minimal power loss
Pass-through audio outputs – Allow the use of multiple amplifiers with a single signal source
Includes input-level setup CD
Signal-sensing on/off operation
Compatible with MS-WBC wireless bass control – Boost bass without leaving the driver’s seat
(sold separately)
Compact form factor
MS-A5001
Digital signal processing amplier
  • Page 1 1
  • Page 2 2

JBL MS-A5001 Datasheet

JBL
Brand
JBL
Model
MS-A5001
Category
Audio amplifiers
Type
Datasheet

JBL MS-A5001 is a great choice for anyone looking to add some serious bass to their car audio system. With 500 watts of power, it can easily drive even the most demanding subwoofers. It also has a variety of features that make it easy to customize the sound to your liking, including a digital input mixer, sophisticated network circuitry, and onboard setup tools.

Here are some of the things you can do with the JBL MS-A5001:

  • Connect up to two subwoofers in parallel
  • Accept any line-level or speaker-level output
  • Easily set up the crossover points and slopes
  • Adjust the input sensitivity and gain
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents