2. Home
  3. Domestic appliances
  4. Sanitary ware
  5. American Standard
  6. Ceratherm M968589
Ceratherm M968589

American Standard Ceratherm M968589, Ceratherm T203430, M968589, T203430 User manual

  • Hello! I am an AI chatbot trained to assist you with the American Standard Ceratherm M968589 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
DIVERTER TRIM KIT
Installation
Instructions
M 9 6 8 5 8 9
M 9 6 8 5 8 9 M 9 6 8 5 8 9
T203430
CERATHERM
CERATHERM
DIVERTER TRIM KIT
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1
ROUGHING-IN DIMENSIONS
MODEL NUMBERS
OPERATING THE VALVE
1
Place ESCUTCHEON (1) onto ESCUTCHEON HOLDER (2).
Align ESCUTCHEON (1). Thread ESCUTCHEON HOLDER (2) onto DIRVERTER VALVE (3).
Tighten until ESCUTCHEON (1) is snug against fiished wall.
TRIM INSTALLATION
1
2
3
2
HANDLE INSTALLATION
Recommended Tools
Flat Blade Screwdriver
Phillips Screwdriver
Remove as much surface dirt and film using clear
water and soft cotton cloth (as described above).
Use any of the following to remove tough surface
film and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth.
To keep your new faucet looking new, please follow
these simple care instructions:
DO: Simply rinse the faucet clean with clear water.
Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing
acids, polish abrasives, or harsh cleaners or
soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
CARE INSTRUCTIONS:
Failure to follow these care instructions may
damage the Faucet's finish.
3
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr od uc t na me s li st ed h er ei n ar e tr ad em ar ks o f Am er ic an S ta nd ar d In c.
© AS A me ri ca , In c. 2 00 8
IN MEXICO 01-800-839-12-00
Turn water supply on and test installed fitting.
Rotate handle to all diverter positions to check operation of valve.
Check for leaks.
012288-YYY0A
ESCUTCHEON KIT
954027-YYYOA
ESCUTCHEON HOLDER
2
1
T203430
A908694-YYY420A
HANDLE
A918428-0070A
SCREW
A907143-YYY0A
HANDLE CAP
A923348-0070A
HANDLE ADAPTER
3
4
5
Install KNOB MOUNT (1) onto VALVE STEM (2).
Align HANDLE (3) and push onto KNOB MOUNT (1).
Thread HANDLE SCREW (4) into VALVE STEM (2) and tighten.
Push END CAP (5) into HANDLE (3).
OFF
ALL CONNECTIONS 1/2" NPT
FINISHED
WALL
FINISHED
WALL
41mm MIN.
(1-5/8)
66mm MAX.
(2-5/8)
71mm
(2-3/4)
57mm HOLE SIZE
(2-1/4)
70mm
(2-5/8)
CHROME
POLISHED BRASS
BLACKENED BRONZE
SATIN NICKEL
002
099
068
295
Replace the "YYY" with
appropriate finish code
DIVERTER TRIM KIT
Installation
Instructions
M 9 6 8 5 8 9
M 9 6 8 5 8 9 M 9 6 8 5 8 9
T203430
CERATHERM
CERATHERM
DIVERTER TRIM KIT
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1
ROUGHING-IN DIMENSIONS
MODEL NUMBERS
OPERATING THE VALVE
1
Place ESCUTCHEON (1) onto ESCUTCHEON HOLDER (2).
Align ESCUTCHEON (1). Thread ESCUTCHEON HOLDER (2) onto DIRVERTER VALVE (3).
Tighten until ESCUTCHEON (1) is snug against fiished wall.
TRIM INSTALLATION
1
2
3
2
HANDLE INSTALLATION
Recommended Tools
Flat Blade Screwdriver
Phillips Screwdriver
Remove as much surface dirt and film using clear
water and soft cotton cloth (as described above).
Use any of the following to remove tough surface
film and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth.
To keep your new faucet looking new, please follow
these simple care instructions:
DO: Simply rinse the faucet clean with clear water.
Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing
acids, polish abrasives, or harsh cleaners or
soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
CARE INSTRUCTIONS:
Failure to follow these care instructions may
damage the Faucet's finish.
3
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr od uc t na me s li st ed h er ei n ar e tr ad em ar ks o f Am er ic an S ta nd ar d In c.
© AS A me ri ca , In c. 2 00 8
IN MEXICO 01-800-839-12-00
Turn water supply on and test installed fitting.
Rotate handle to all diverter positions to check operation of valve.
Check for leaks.
012288-YYY0A
ESCUTCHEON KIT
954027-YYYOA
ESCUTCHEON HOLDER
2
1
T203430
A908694-YYY420A
HANDLE
A918428-0070A
SCREW
A907143-YYY0A
HANDLE CAP
A923348-0070A
HANDLE ADAPTER
3
4
5
Install KNOB MOUNT (1) onto VALVE STEM (2).
Align HANDLE (3) and push onto KNOB MOUNT (1).
Thread HANDLE SCREW (4) into VALVE STEM (2) and tighten.
Push END CAP (5) into HANDLE (3).
OFF
ALL CONNECTIONS 1/2" NPT
FINISHED
WALL
FINISHED
WALL
41mm MIN.
(1-5/8)
66mm MAX.
(2-5/8)
71mm
(2-3/4)
57mm HOLE SIZE
(2-1/4)
70mm
(2-5/8)
CHROME
POLISHED BRASS
BLACKENED BRONZE
SATIN NICKEL
002
099
068
295
Replace the "YYY" with
appropriate finish code
DIVERTER TRIM KIT
Installation
Instructions
M 9 6 8 5 8 9
M 9 6 8 5 8 9 M 9 6 8 5 8 9
T203430
CERATHERM
CERATHERM
DIVERTER TRIM KIT
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1
ROUGHING-IN DIMENSIONS
MODEL NUMBERS
OPERATING THE VALVE
1
Place ESCUTCHEON (1) onto ESCUTCHEON HOLDER (2).
Align ESCUTCHEON (1). Thread ESCUTCHEON HOLDER (2) onto DIRVERTER VALVE (3).
Tighten until ESCUTCHEON (1) is snug against fiished wall.
TRIM INSTALLATION
1
2
3
2
HANDLE INSTALLATION
Recommended Tools
Flat Blade Screwdriver
Phillips Screwdriver
Remove as much surface dirt and film using clear
water and soft cotton cloth (as described above).
Use any of the following to remove tough surface
film and build-up:
Mild liquid detergents
Clear ammonia free liquid glass cleaners
Non-acidic, non-abrasive gentle liquid or fully
dissolved powder cleansers mixed according to
manufacturers directions.
Non-abrasive liquid polishers
Once clean, rinse faucet again with clear water to
thoroughly remove cleaner or polish and blot dry with
a soft cotton cloth.
To keep your new faucet looking new, please follow
these simple care instructions:
DO: Simply rinse the faucet clean with clear water.
Dry the faucet with a soft cotton cloth.
DO NOT:
Do not use any abrasive cleaners, cloths, or
paper towels.
Do not use any cleaning agents containing
acids, polish abrasives, or harsh cleaners or
soaps.
Regular and routine cleaning will reduce the need for
heavy cleaning and polishing. If heavy cleaning is
required, the following procedures are recommended:
CARE INSTRUCTIONS:
Failure to follow these care instructions may
damage the Faucet's finish.
3
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr od uc t na me s li st ed h er ei n ar e tr ad em ar ks o f Am er ic an S ta nd ar d In c.
© AS A me ri ca , In c. 2 00 8
IN MEXICO 01-800-839-12-00
Turn water supply on and test installed fitting.
Rotate handle to all diverter positions to check operation of valve.
Check for leaks.
012288-YYY0A
ESCUTCHEON KIT
954027-YYYOA
ESCUTCHEON HOLDER
2
1
T203430
A908694-YYY420A
HANDLE
A918428-0070A
SCREW
A907143-YYY0A
HANDLE CAP
A923348-0070A
HANDLE ADAPTER
3
4
5
Install KNOB MOUNT (1) onto VALVE STEM (2).
Align HANDLE (3) and push onto KNOB MOUNT (1).
Thread HANDLE SCREW (4) into VALVE STEM (2) and tighten.
Push END CAP (5) into HANDLE (3).
OFF
ALL CONNECTIONS 1/2" NPT
FINISHED
WALL
FINISHED
WALL
41mm MIN.
(1-5/8)
66mm MAX.
(2-5/8)
71mm
(2-3/4)
57mm HOLE SIZE
(2-1/4)
70mm
(2-5/8)
CHROME
POLISHED BRASS
BLACKENED BRONZE
SATIN NICKEL
002
099
068
295
Replace the "YYY" with
appropriate finish code
/