Shinko Quick Reference User manual

Shinko
Brand
Shinko
Model
Quick Reference
Type
User manual

This manual is also suitable for

S G D □ - □ □ □ □ - □ - □
Option
0: No option needed, 1: Multi-rotation trimmer
2: Moisture-proof treatment
3: Multi-rotation trimmer+Moisture-proof treatment
Power supply
0: 100 to 240 V AC, 1: 24 V AC/DC
*2
Output 2
*1
Output
*2
, Output 1
*1
Input
Series name
SGD: 1-output, SGDW: 2-outputs
SGDL: 1-output + Serial communication
(
F
or detailed input/output spec, refer to the full Instruction Manual.
)
*1: For SGDW only
*2: For SGD, SGDL only
Default Display
Custom display
mode 3
Custom display
mode 4
Unlit
display mode
All unlit
display mode
Model display
mode
RUN display
mode 1
DISP
key
RUN display
mode 2
RUN display
mode 3
RUN display
mode 4
RUN display
mode 5
RUN display
mode 6
Custom display
mode 1
DISP
key
DISP
key
DISP
key
DISP
key
DISP
key
DISP
key
Custom display
mode 2
DISP
key
DISP
key
DISP
key
DISP
key
DISP
key
DISP
key
MODE
key
for 5 sec
MODE
key
Input
setting mode
Output 1
setting mode
Output 2
setting mode
Instrument
setting mode
Communication
setting mode
C
ustom
display
setting mode
Manual mode
DOWN
key
for 3 sec
key
for 3 sec
Decimal
point place
key
Output 0%
value
DI
SP
key
Output
100% value
key
Indication
unit
key
Save
settings
key
Output 1
type
O
utput
1
decimal
point place
Indication
value at
output 0%
Ind
ication
value at
output 100%
Output 1
Normal/Reverse
Save
settings
Output 2
type
O
utput 2
decimal
point place
Indication
value at
output 0%
Indication
value at
output 100%
Output 2
Normal/Reverse
Save
settings
Filter time
constant
Sensor
correction
Indication
time
Auto/Manual
Manual mode
auto return time
Save
settings
Instrument
number
Communication
speed
Data bit/
Parity
Stop bit
Response
delay time
Save
settings
Multi-Display
A
Multi-Display
B
Save
settings
Default DisplayDefault Display
Default Display
Default Display
Default Display
Default Display
M
ODE
k
ey, or after
Manual mode auto return
time has elapsed
key
key
key
for 3 sec
key
key
key
key
key
for 3 sec
key
key
key
key
key
key
MODE
key
MODE
key
MODE
key
MODE
key
MODE
key
key
for 3 sec
key
key
key
key
key
key
key
key
key
key
key
key
key
for 3 sec
key
key
key
key
for 3 sec
Square root
function
key
Low level
cutoff
key
No.
1
No. 6
No.
1
No.
6
No. 1 COM
No. 2 NC
No. 3 YB(+)
No. 4 YA(-)
No. 5 NC
No.
6
COM
Output 1
circuit
Output 2
circuit
CPU
Input
circuit
Front
trimmer
Power
circuit
Display/
Setting key
circuit
A/V
+
-
+
-
24V
power
circuit
250
Power for
2-wire
transmitter
+
-
QUICK REFERENCE [Applicable model: SGD, SGDW, SGDL] No. SGD12JE1 2018.10
Decimal point place
No decimal point
1 digit after point
2 digits after point
3 digits after point
Indication unit
No unit
%
mA
V
°C
Square root function
Enabled
Disabled
Save settings
Save
Not save
Output 1, Output 2 type
4 to 20 mA
0 to 20 mA
0 to 16 mA
2 to 10 mA
0 to 10 mA
0 to 10 mV
0 to 100 mV
0 to 1 V
0 to 5 V
1 to 5 V
0 to 10 V
-5 to 5 V
※1
Output 1,2 decimal point place
No decimal point
1 digit after point
2 digits after point
3 digits after point
Selection Item List
Model Name
Circuit Configuration
SGD, SGDL
SGDW
Characters
Indication
Number, °C/°F -1 0 1 2 3 4 5 6 7 8 9 °C °F
Indication
Alphabet A B C D E F G H I J K L M
Indication
Alphabet N O P Q R S T U V W X Y Z
Terminal Arrangement
SGD, SGDL SGDW SGDL only
RS-485 serial communication
Modular jack pin arrangement
Output 1,2 Normal/Reverse
Normal
Reverse
Auto/Manual
Auto
Manual
Communication speed
9600 bps
19200 bps
38400 bps
Data bit/Parity
8 bits/No parity
8 bits/Even
8 bits/Odd
Stop bit
1 bit
2 bits
Key Operation Flowchart
Display Mode
• : Available only for the SGDW.
• For the details of the display mode, refer to the full Instruction Manual.
Default Display
• If the MODE and DISP keys (in that order) are pressed together for approx. 3
seconds in any display mode, the display mode will become the Default Display.
• Once the Default Display is set, the DISP key will be in lock status.
• If the DISP key is pressed for approx. 3 seconds, the key lock status will be
cancelled.
• If the DISP key is pressed while the DISP key is in lock status, Multi-Display A
will indicate
.
Setting Mode
• Output 2 setting mode is available only for the SGDW.
• Communication setting mode is available only for the SGDL.
• If the MODE key is pressed for approx. 5 seconds in each setting mode, the
unit will move to the Default Display.
※1 Not available for the SGDW.
和文は裏面をご覧下さい。
Output
circuit
C
ommu
-
nication
circuit
Modular
jack
CPU
Input
circuit
Front
tri
mmer
Power
circuit
Display/
Setting key
circuit
A/V
+
-
+
-
For SGDL
24 V
power
circuit
250
Power for
2-wire
transmitter
1
4
8
9
13
14
12
2
6
3
5
7
10
11
1
8
  • Page 1 1

Shinko Quick Reference User manual

Shinko
Brand
Shinko
Model
Quick Reference
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents