Sanyo VHR-630 is a video cassette recorder featuring VHS high picture quality technology. It can be connected with a standard aerial or, for high quality of picture and sound, via AV to a TV receiver. It's equipped with G-CODE timer recording capability, featuring on-screen programming. It can play NTSC tapes and features extended playback modes, including endless play, variable speed playback and index search. It supports frame advance and has a counter with reset function, as well as a digital clock that can be set manually.
Sanyo VHR-630 is a video cassette recorder featuring VHS high picture quality technology. It can be connected with a standard aerial or, for high quality of picture and sound, via AV to a TV receiver. It's equipped with G-CODE timer recording capability, featuring on-screen programming. It can play NTSC tapes and features extended playback modes, including endless play, variable speed playback and index search. It supports frame advance and has a counter with reset function, as well as a digital clock that can be set manually.
INSTRUCTION MANUAL
Video cassette recorder
si/j14
VHR-630
G-CODEIHQ BEl
PAL NTSC443
Makesuretomakethese
settingsbeforeoperatingthe
VCR.
NOTE
Thismanualcoversthemodel
VHR-630,whichissoldin New
ZealandandinAustralia.
Thewarrantyofferedisdifferent
accordingonwheretheunitis
sold,Forcustomersin New
Zealand,pleaserefertothe
WarrantycardforNewZealand.
ForcustomersinAustralia,
pleaserefertotheWarrantycard
andtotheExtended
Manufacturer’sWarrantyPlan
forAustralia,
WarrantycardforNewZealand
Warrantycard
for Australia
Q
--”-*
-------- %.+
--... ----+-
-----
-...
“=%%?
I
ExtendedManufacturer’s
WarrantyPlanforAustralia
iii
CONTENTS
1
PRECAUTIONS
.....................................................
2
CONTROLS
.........................................................
3
INTRODUCTION
Remote control batteries insertion ............................ 3
2
PREPARATION
CONNECTIONS
.....................................................
4
Accessories ............................................................... 4
“..
.“ “..-..“......, ......
VCR PRESETTING
.................................................
5
Iml!lm
Adjusting the TV receiver to the video channel ......... 5
-
Tuning control (Auto) ...... ........................................ 5
-
Clock setting ........ ...... ...... ..................................... 6
VCR Setup ................................................................. 7
ON-SCREEN MENUS AND BASIC CONTROL ................... 8
3
BASICOPERATION
PLAYBACK
..........................................................
Variable playback modes ............... ...... ...................
Playback of an NTSCtape .........................................
Counter memo~ .......................................................
Index search .............................................................
Endless play ..............................................................
RECORDING TV PROGRAMMED
................................
Quick Start Recording timer .....................................
9
9
10
10
10
10
11
11
4
G-CODE TIMER RECORDING PROGRAMMING ................... 12
On-screen programming ........................................... 12
ON-SCREEN
Programming on the VCR display ............................. 13
OPERATION
ON-SCREEN TIMER RECORDING PROGRAMMING ........... 14
Confirmation/Cancelling ............................................ 15
5
ADVANCED
OPERATION
TAPE COPY
.........................................................
15
6
TROUBLESHOOTING
..............................................
16
SPECIFICATIONS
..................................................
17
OTHER
1
PRECAUTIONS
Safety precautions
Operating precautions
DANGER:
This VCR contains live parts. Do not remove
the cabinet.
WARNING:
To prevent fire or shock hazard, do not
ex~ose this product to rain or moisture.
CAUTION:
Do not put your hand or other objects in the
cassette loading slot because of the risk of
injury or an accident. Be sure to keep small
children away from the VCR.
Caution concerning condensation
Be careful of condensation
Condensation can form inside a VCR when it
is suddenly moved from a cold place to a
warm, humid one, or when a heater has been
turned on to quickly heat the room.
Do not insert a video cassette if you use
this
VCR in areas subject to condensation.
Wait for 1-1/2 to 2 hours to completely
eliminate condensation before using the
VCR.
●
●
●
●
●
●
●
●
●
●
●
Place the VCR on a flat, stable, level
surface. Never subject it to violent shaking
or any other shock or impact.
Do not expose the unit to high
temperatures. Excessive heat (heat
sources such as heaters, ovens, closed
car on hot days, etc. ) may damage the unit.
Be sure to use this VCR only in a
temperature range of 5°C to 40°C (41 “F to
105”F) and at less than 80’%0humidity.
Do not use the unit under the following
conditions:
—
in locations with high humidity
—
in presence of excessive dirt or dust
—
in areas subject to strong vibrations
—
near strong magnetic fields (e.g.
transmitting antennas, motors,
fluorescent lights, etc.)
Do not stack anything on top of your VCR,
or block the air vents, to prevent damaging
or overheating.
Do not place anything, except VHS video
cassette tapes, in the unit.
Do not allow rain, steam, dew, salt water,
sand, oily smoke, metal objects, etc. to
enter the unit
Clean with a dry and soft cloth, or soft cloth
slightly moistened with a mild detergent
solution.
Do not use any type of solvent, such as
alcohol or benzine.
Do not forget that even in the power off
state there is an electrical voltage inside
the VCR as long as it is connected to a wall
socket.
Disconnect the power cord from the wall
socket if the VCR is not to be used for a
long time.
I
INTRODUCTION
Onlycassettesmarked~ canbe
usedwiththisVCR.
Videocassetterecordersbearingthe
“#=lQ” markincorporateVHShigh
picturequalitytechnology.Notethat
thereisinterchangeabilitywithformer
VHSvideocassetterecorders,
Note:
Iftheunitdoesnotoperateproperly,
switchit off,referto
“TROUBLESHOOTING”orcontact
yourSanyoauthorizedserviceagent.
Power on/off
Powerisswitchedon/offbypressing
thePOWERbutton. .
VCRdisplay
Poweron
Powerotf
“Poweroff istheconditioninwhich
onlythetimeisdisplayed
2
INTRODUCTION
Remote control batteries
insertion
1
2
Slideopenthelid.
Insert2 “AA (IECR6)” 1.5
volt batteries(supplied)
according to the@ and@
signs.
3 Replacethe lid,
Functionindicator
—
Mode
Playback
Forwardsearch
Fast-forward
Rewind
Reverse search
Record
Record pause
Still picture
Frame advance
Display
(;;;: Flashing)
M
CONTROLS
Remote control sensor
Operate the remote control unit within a range of
approx. 30” and approx. 6m (20 ft.) from the front of
the VCR.
Indication
Function
CHANNEL+, –
Tuner programme selection
FF Fast-forward, forward search during playback
PAUSE/STILL
Pause during recording, still picture during playback
PLAY Playback
POWER Power onloff
REC Recording
REW Rewind, reverse search during playback
STOPIEJECT
Tape stop, cassette ejection
(On the remote control only)
CH+, CH–
Programme selection
CLEAR Clears data
G-CODE G-Code timer programme set
INDEX Index search
INPUT External input mode selection
MEMORY Counter “0:00:00” position memory
MENLf/TV
On-screen operation
OK Confirms data
PRESET Tuner preset
RESET Counter reset
o-9 Direct programme selection, for various input
CONNECT
ONS
Aerial/RF connection
Connect as indicated below.
l%=!
Aerial
.F?
To a wall socket
Power cord
d~
m
m
1411
b’
AV
Aerial output cable
connection
If your TV receiver has an AV terminal, the
following AV connections are also possible.
● The advantage of this connection is a
higher quality of picture and sound during
playback.
TV Aerial
m
c=l====1=12===il
IIrl—l-l FillI
1111 II
w. II I
%==
I H ‘Mm?”
I I I AV-cable (not supplied) I I I
Aerial output cable
2
PREPARATION
Accessories
Is everything inthebox?
Power cord
Aerial output cable
Remote control unit
I
2 “AA (IEC R6)” size,
1.5-voit batteries
2
VCRPRESETTINGPREPARATION
D
...............
r:~:—
...............
After all the connections are completed, please follow steps
- to - before using the VCR.
_ Adjusting the TV receiver to the video channel
_ Tuning control (AUTO)
_ Clock setting
—OK
Emzl
s When the AUTO SETUP screen is clear,
Adjusting the TV receiver to the video
press the OK button.
channel
● Auto tuning will start.
1 Press the POWER button
-
2 TumonvourTV
Tuning control (AUTO)
IfyouwanttorecalltheAUTOSETUP
screen,simplypress both CHANNEL
(+
and-) buttonsontheVCRfor 3
seconds or more.
.
For more details, please refer to your TV
receiver instruction manual.
Auto tuning
This VCR has a built-in tuner capable of
tuning up to 44 TV stations. Each TV station
broadcasting channel is memorized by the
VCR as a programme position number (01 -
44).
The TV stations available in your area will be
Note:
If the VCR has been connected to the TV using the
“AV
connection”, simply set your TV receiver to
the
“AV” mode and the AUTO SETUPscreen will
appear on your
TV screen. Go to step 5.
If in your area, UHF channel36
(37- 38) isusedbya
broadcaster,followthesteps
below.
3
4
In case of an “RF connection”, set your
TV receiver to “VCR” or the position
designated for VCR use (usually a
position where no TV programme is
received),
For more details, please refer to your TV
receiver instruction manual.
automatically preset in orde; starting from
programme position number “01”.
Because of this you may have to sort the TV
stations into the correct order. Please refer to
“Sorting the TV stations”.
When all available TV stations have been
preset, the function will stop and the TV
station preset to programme position number
1
2
3
Tunethe
TVreceiverto an
availableUHFchannelbetween
channel32and41(33and43)(a
UHFchannel
not used by aTV
station).
Usingasmallscrewdriver,slowly
turnthevideochanneladjustment
screw“RF CHANNEL” on the
backof the VCR,to the right for a
higher channel than 36 (37-38)
and to the leftfor a lower channel
than 36 (37-38),
Adjust thetuning on the TV, if
necessary,so that theAUTO
SETUPscreenis clear.
Adjust the tuning on the TV to UHF
“01” will be tuned on-your TV screen.
channel 36 (37 - 38) so that the AUTO
SETUP screen is clear.
TV screen
Notes:
● During the auto tuning operations, please do not
press any of the buttons or controls on the VCR
or remote control
● Auto tuning is not possible if the VCR is set to
AV input mode.
● The skip function will be automatically set for all
position numbers
where no TV station has been
weset,
AUTO SETUP
[OKI +ENTER
[MENU] +TV
—
This is your video channel.
To view a tape playback or to watch a TV
broadcast tuned on the VCR tuner, set the TV
to the video channel.
~ “?:
RF CHANNEL
Australia 37-38 33-43
5
Emn
Clock setting
&an@e: Date. 9 December, 1996
Time... 16:15
1 Press the MENLVTVbutton.
2 Set the date and time using the numeric
buttons (O- 9).
Enter in sequence, 0912961615.
\
CLOCK SET
09.12.96
16:15
[+/-] +Tl ME SHIFT
[CLEAR] +TO CORRECT
[OKI +ENTER
If you entered a wrong number, press the
CLEAR button to delete it, then enter the
correct number.
For time shifting adjustment, simply press the
(CH+ or CH-) button.
3 When finished, press the
OK button.
● Seconds will start counting from “00” as
the OK button is pressed.
● The normal TV broadcast screen will return,
Additional tuning adjustments
Sorting the TV stations
&/e: TOchange TV1 from programme
position “4” to programme position “1”.
I TV4 TV2 TV3 ! Tvl \
..............
TV station
Programmepositionl ~ 2 3 ~ 4 ~
1
2
~
J ~J/
4 ~1~
i............i
Press the PRESET button.
Using the (CH+ or CH–) button select the
desir;d TV station
(e.g.’TVl).
TV1
I
3 Using the numeric buttons (O - 9), enter the
target programme position number (e.g.
“01 “).
4 Press the OK button
Repeat steps 2 to 4 to change another TV
station programme position number.
5 When finished, press the
PRESET button.
Fine tuning
If the tuning is not optimum, it can be
improved by manual fine tuning.
1 Press the PRESET button.
2 Press the
FF or REW button to obtain the
best possible picture and sound.
3 Press the OK button.
4 When finished, press the PRESET button.
Skip function
If only programme position numbers 1 to 30
have been preset, set the skip function for
programme position numbers 31 to 44, so
that only the preset TV stations will appear
when pressing the
(CH+ or CH-) button.
1 Press the PRESET button,
2 Using the numeric buttons or the
(CH+ or
CH–)
button, select the programme
position number to skip,
3 Press the
CLEAR button.
● The “S” indicator will light,
To cancel the skip function, press the
CLEAR button again to erase the “S”
indicator,
4 Press the
OK button.
Repeat steps 2 to 4 for every programme
position number to skip.
5 When finished, press the
PRESET button.
Manual tuning
This tuning mode can be used to modify the
settings entered by the Auto tuning function,
or to manually preset the TV stations to
particular programme position numbers
1
2
3
4
Press the PRESET button.
Using the
(CH+ or CH-) button, select the
desired programme position number.
Press the
PLAY button.
If the search stops on a broadcast other
than the one desired, press the
PLAY
button again until the broadcast from the
desired TV station appears on the TV
screen.
Press the
OK button when the desired TV
station appears on the TV screen.
Repeat steps 2 to 4 to preset another TV
station to another programme position
number,
5 When finished, press the
PRESET button.
2
PREPARATION
i
‘REsET7Fil
PLAY
u
ower interruption
thepower to the VCRhasfailed or
is beendisconnectedfor morethan
hour, the VCRdisplay shows
,,
.,-—
owever,the tuner presetmemorywill
]t beerased,So there isno needto
tune the
VCRstations.
]e
date,timeandrecording
formationregardingfuture
cordingsshouldbereset,
rstrefer
to “m Clock
!tting” on page6, to set theclock
ateand time), then, the timer
cording programmedshould beset
lain asdesired.
MewZealand only
runingorpresettingtheVCR
;hannels
rhis isvery important for correct
;-Code operation.
deallyfor simpleroperation,
:hannelsshould bepresetasfollows:
Television
Programme
station
position numbar
Tvl
1
TV2
2
TV3
3
coradditional channels in your
~reait is overto you to selectthe
nest logical channel position to
]Iace them.
*SkyTelevision
4
* CanterburyTV
5
*ActionTV
6
● Whenyou usetheG-Codefunction
to prograrnmearecordingfroma
certainchannelfor thefirsttime,itwill
askyou theprogrammeposition
numberthatchannelwaspresetto,
Thatsettingwill bememorizedand
automaticallysetthenexttimethe
samechannelisselected.
2
PREPARATION
-o-9
Thesettings indicated by the “O”
symbols arethe factory default
settings.
7
VCRPRESETTING
VCR Setup
The VCR Setup is done using the VCR Setup menu.
1
2
Press the MENWTV button, then press the numeric 3 button.
0. AUTO TUNING MEMORY
1. NTSC PBOPAL-TV NTSC443
Each item to setup is selected by pressing the corresponding numeric button. To set a
different mode, press repeatedly the numeric button corresponding to the item to set, until the
symbol c’.” is displayed to the left of the desired setting.
Note:
Be careful not to press the numeric button O if you do not wish to reprogramme all programme positions
If the numeric
Obutton is pressed .....
O. AUTO TUNING MEMORY
Auto tuning
The Auto tuning function will start, and all programme
positions will be automatically reprogrammed.
If the numeric
1 button is pressed .....
1.NTSC PB
NTSC playback
0 PAL-TV: When using a PAL system TV.
NTSC443: When
using an NTSC4,43 system TV.
Please use the
AUDIOMDEO OUT terminals.
3
When finished, press the MENUTW button.
ON-SCREENMENUS ANDBASIC CONTROL
The VCR can easily be programmed by using the menus displayed on-screen.
The menus are controlled from the remote control.
The buttons that can be used with each menu are displayed at the bottom of the screen.
If you learn the basic operations, each setting can easily be made by following the steps of the
concerned menu.
If a wrong sub-menu has been selected, press the
MENLVTVbutton to return to the main menu,
and start again
MENI.UTV
4
1. Timer recording
programming
(see
page 14)
MENU
1. T IMER PROGRAM SET
2. PROGRAM CHECK/ CLEAR
3. VCR SETUP
F
.m
4. CLOCK SET
mm
[0-91 +SELECT
[MENUI +TV
09.12.96
16:15
I
G-tom
o
$,
::,
G-CODE NUMBER
489135 ---
[OKI +ENTER
[CLEARI +TO CORRECT
[G-CODE] +TV
G-Code timer recording
programming
(see
page 12)
.
.
PR DATE START END
02 25.12 10:30 11:00
+--------- :----: --
---- ---
--:-- --:--
----.-- --:--
--:--
-- -- -- --: ---- :--
-------
--:-- --:--
[CLEARI +TO CORRECT
[MENUI +TV
\
2. Confirmation/Cancelling
(see page 15)
PR DATE START END
+01 23.12
15:30 16:00
02 25.12 10:30 11:00
-- -- -- --: ---- :--
----,-- --: ---- :--
-- --, ---- :---- :--
------
----- -----
[+1-I &LECT”
[CLEARI +CANCEL
[MENUI +TV
3. VCR Setup
(see page 7)
-+
I
I
[0-91 +SELECT
[MENUI+TV
4. Clock setting
+
(see page 6)
CLOCK SET
09.12.96
16:15
[+/-] +Tl ME SHIFT
[CLEARI
●TO CORRECT
[OKI +ENTER
2
PREPARATION
ii
P
G-COOE
MENWTV ~ ; ~
o-9
0
OK
8
3
BASICOPERATION
%
000
000
0-9
CH+, - ~
PLAY
FF
REW
PAUSEI
STILL
STOP
EJECT
Auto power on
Thepowerisautomaticallyswitched
onasacassetteisinsertedwhilethe
VCRis inthestand-bymode.
Auto play
TheVCRwill playbackatape
automatically
when avideocassette is
insertedwhose erasure-preventiontab
hasbeen removed.
Autoeject
Whenavideocassettewithoutan
erasure-preventiontabisplayedtoth[
end of the tape,the tapewill be
automatically rewound andthen the
cassettewill beejected,
Power oft eject
The
video cassettewill be ejected
whentheEJECTbuttonis pressed,
evenwhen theVGRisinstand-by
mode.
PLAYBACK
1
2
3
4
Turn on the TV, then set it to the preset
video channel or AV mode.
Insert a recorded video cassette.
Cassette loading
Gently push the centre of the cassette
until it is loaded automatically
Press the
PLAY button,
To stop the playback, press the
STOP
button.
● TO rewind the tape, press the REW button.
● To advance (fast-forward) the tape, press
the
FF button.
● To eject the video cassette, press the
EJECT button on the VCR.
Variable playback modes
Forward search
1
Press the FF button during playback or
fast-forward operation.
2
Press the PLAY button to resume normal
playback, or the FF button to resume
fast-forward operation.
Reverse search
1
Press the REW button during playback or
rewind operation.
2 Press the
PLAY button to resume normal
playback, or the
REW button to resume
rewind operation.
Still picture
1
Press the PAUSEISTILL button during
normal playback.
2 Press the PLAY button to resume normal
playback.
Frame advance
1
Press the PAUSEA3TILL button during still
playback to advance the picture frame by
frame.
2 Press the
PLAY button to resume normal
playback.
Tracking adjustment
This VCR starts the automatic tracking
function when you insert the tape, During
playback this function will adjust the tracking
to the best possible image. If noise appears
in the playback picture, press the
(CH+ or
CH–) button, to reduce the noise interference
in the image
Noise interference
Note:
Depending on the cassette tape, you may find that
some noise interference cannot be completely
corrected using the tracking controls.
If the still picture moves up and down
Use the
(CH+ or CH–) button, to correct.
When noise interference is corrected using
the
(CH+ or CH–) button, the settings will be
effective until the cassette tape is unloaded.
Once the cassette tape is unloaded, the VCR
is reset and the next time the VCR is
used
you may need to do the corrections again.
Notes:
●
●
During variable playback modes the picture may
contain some noise or vibration that cannot be
corrected. This is not a malfunction.
If still picture playback is continued for about
five minutes, the VCR will automatically change
to stop mode in order to prevent the tape from
being damaged.
Playback of an NTSC tape
Endless play
This VCR can playback an NTSC tape on a
PAL standard TV receiver.
However, please note the following points.
●
●
●
●
If the image is unstable, rolling vertically,
use the TV vertical hold button to stabilize
the image.
The image may shrink vertically and a
black band may appear at the top and
buttom of the screen,
An NTSC tape cannot be copied normally.
Picture quality of NTSC tapes cannot be
This function will play back a tape to the end,
rewind it then replay it again, and again until
you stop it.
1 In the stop or playback mode, first press
the
PLAY button then while holding it down
press the REW button.
2 To cancel the endless play, press the
STOP button.
If the counter memory function is used in
combination with endless play, the VCR will
play back the tape to the counter reading
—
guaranteed with this VCR
Counter memory
The counter memory is used to find a point on
the tape, At the desired point, press the
RESET button to reset the counter to
“0:00:00’.
Then, press the MEMORY button to display
“~” to the left of the counter reading.
After recording or playback, that point can be
easily found by pressing the REW button (or
the FF button if the counter reading is
negative), the tape will be rewound (or
fast-forwarded) and stop at the memorized
position.
Notes:
● Whenever you load a cassette tape, the counter
is reset to “0:00:00”.
. If you play back a blank tape or a blank Dortion
of tape, the counter will not operate.
Index search
This VCR will go automatically to the
beginning of the next (or present) recording
and start playback.
An index signal is automatically placed at the
beginning of each recording made on this
VCR, This index can be used to search for
the next (or present) recording,
1
2
Press the
INDEX button while in the stop or
playback mode.
To cancel the index search mode, press
the INDEX button again.
Press the FF or REW button.
The search function will start.
mmml
To stop the search function, press the
STOP button.
Notes:
● Make sure that indexes are at least five minutes
apart from each other.
● Index signals are not recorded after a recording
pause.
“11’vl_0:00:00” then start again from the
beginning
Counter”~
0:00:00” position
Beginning
Playback
I
End
Rewind
Notes:
● During endless play, please do not press FF,
REW or PAUSE/STILL button because the
endless play will be cancelled.
● This function can only be activated using the
controls on the
VCR itself
from the remote control.
It cannot be activated
3
BASICOPERATION
*
PLAY
J
REW
MEMORY
STOP
—FF
—INDEX
—RESET
PLAY STOP
REW
44
CH+,-
REC
P:tJJ:[
STOP
Erasure-prevention tab
Topreventaccidentalerasure,
removethetabafterrecording
@
❑
Torecordagain,covertheholewith
vinyltape.
I
Mis-erasurepreventioneject
Thecassettewill automaticallybe
ejectedifrecordingisattemptedona
videocassettewithoutan
erasure-preventiontab.
Auto rewind
TheVCRautomaticallyrewindsthe
tapewhenit reachesthe
end. This
functiondoesnotoperatewithtimer
recordingorQuickStartRecording
timer,
11
RECORDINGTV PROGRAMMED
1
2
3
4
5
Turn on the
TV then set it to the preset
video channel or AV mode.
Insert a video cassette with
erasure-prevention tab.
Press the numeric buttons, or the
(CH+ or
CH-) button, to select the TV station to be
recorded.
Press the
REC button.
The
“REC”indicator will light, and
recording starts.
To stop the recording, press the
STOP
button
If you wish to avoid recording
unwanted material
1
During recording, press the PAUSE/STILL
button.
The TV picture and sound will not be
recorded,
2 Press the
PAUSE/STILL button or REC
button.
The recording will resume.
Note:
If the record pause mode continues for about five
minutes, the VCR will automatically go into the stop
mode in order to prevent damage to the tape.
Recording one programme while
watching another
1
2
Start recording the desired TV station
programme selected on the VCR.
Select on the TV receiver the TV station you
want to watch,
If the VCR has been connected to the TV
using the
‘(AVconnection”, set the TV to
the TV mode.
Quick Start Recording timer
Timer recording is simple.
You can start a recording and then
programme when the VCR is automatically
recording and turn its power off.
1 Press the REC button twice.
2 Within 10 seconds, set the recording end
time by using REC and (CH+ or
buttons.
REC: units of 30 minutes
(CH+, CH-) : units of 1 minute
Rmlllll
The timer indicator (~) will light after the
recording end time is set.
To stop the recording at any time, press the
STOP button
Checking/Changing
When the REC button is pressed during
Quick Start Recording, the recording end
time will blink for 10 seconds.
The recording end time can be changed by
pressing REC and (CH+ or CH–) buttons
during this 10-second period.
G-CODETIMER RECORDING
PROGRAMMING
There are two ways of programming G-Code
timer recordings.
One is using the on-screen display and the
other one is using the VCR
display.
● You can set up to 6 programmed to be
recorded upon a period of
up to 1 year.
On-screen programming
1 l,,rn on d,cTVthcm se, i, to [he prrxcl
video channel or AV mode.
Z Press dwG-CODEbutton.
● If 6 timer recordings have already been
set, the programmed timer recordings list
will appear on the TV screen,
Please refer to “Confirmation” and
“Canceling” on page 15,
m
3
Using the numeric buttons, enter the
Code number for the programme you
want to record,
&mrp/e; Enter the Code number 489135,
G-CODE NUMBER
489135 ---
I
If you entered a wrong number, press the
CLEAR button to delete it, then enter the
correct number.
q Press the OK button
● The settings for the programmed
recording are displayed.
G-CODE NUMBER
489135 ---
PR DATE START END
+01 25.12 15:00 16:00
Notes:
If the programme position number (PR) displays
“-_, ~:
. Enler the programme position number the TV
station has been preset to.
● That setting will be memorized and set the next
time the same TV station is selected.
s When all the settings areas desired,
press the OK button.
You can programme another recording by
repeating steps 3 to 5.
6 Insert a video cassette with
●
erasure-prevention tab.
Make sure the tape is longer than the total
recording time.
T Press thcG-CODE button.
● The timer indicator (~) will light on the
VCR display and the VCR goes into timer
recording stand-by mode,
Additional settings
After pressing the OK button in step 4.
Daily/Weekly recording
Prcw lhc
MENWTV button rcpcatccfiy to
select:
“M-F”: ior daily recording (Monday through
Friday)
I
“WK”: for weekly recording (the same
programme every week)
No display: for one time recording
Note:
Daily recording starting on a Saturday or Sunday
will not be possible.
Changing the off time
Each press of the
(CH+ or CH-) button will
change the recording off time by units of 10
minutes.
Notes:
●
●
●
If the date and time are not set, the G-CODE
button will not function.
The (PI) indicator will flash if no video cassette is
loaded when
going into timer stand-by mode.
Ttw (B) indicator will flash and the video
cassette is ejected if a video cassette with no
erasure-prevention tab is loaded.
4
ON-SCREENOPERATION
i
– G-CODE
—--o-9
—OK
— _——___ .—..-
IisVCRhasabuilt-in G-Code
s[em.Programmingtimer
cordingsisnowassimpleas
IteringaCodenumbernumber(1to
digits)listednexttoeach
ogramme
in your local TVguide or
!wspaperTVprogramme listing.
G-Code isatrademarkarmliedforbv
GemstarOevelDpmerrlCo~p. ‘
G-Code systemismanufactured
underlicensefromGemstar
DevelopmentCorporation.
NewspaperorTVguide
Code number
0
Jj
—..-,
L
MENWTV -1 {I , ,
-- G-CODE
:::’2:
-–-o-9
CH+, ---I,-, ~; _–.. oK
CLEAR –-
13
i
G-CODE TIMER RECORDINGPROGRAMMING
——
Programming on the VCR display
You can programme or confirm a G-Code
timer recording on the VCR display even if
the TV is turned off.
1
Press the G-CODE button.
● 9 bars (-) will appear on the display,
● If 6 timer recordings have already been
set, the 9 bars (-) are not displayed.
Please refer to “Confirmation” and
“Canceling” on page 15.
z Using the numeric buttons, enter the
Code number for the programme yo!~
want to record,
&/e: Enter the Code number 489135
If you entered a wrong number, press the
CLEAR button to delete it, then enter the
correct number,
3
Press the OK button.
The programmed recording programme
position number ;]rrd recording on tirnc
are displayed.
Notes,
If the programme position number (Pf’1) displays
$1--1’:
● f?nterthe programrrm position number the l-V
station has been prmx?t10,
● TIwl sc[ting will be mcrn )rizerf ancl s[
ON-SCREENTIMER RECORDING
PROGRAMMING
_——
~xanT~/e: Prouramme position.., 02
1
2
3
4
Dat;... 25 December
Start time... 21:30
End time... 23:15
Turn on the
TV then set it to the preset
video channel or AV mode.
Press the
MENLVTVbu({on.
Pr(?s:;Ihrl! numeric 1 b(ll[O1l.
Usilng [he numeric bu[lons, SCIthe
prog;amrne posi[ion number (c,g. ‘102”).
Example: Enter 02,
~ Using the numeric buttons, set the date
(e.g. 25 December).
~xampfe: Enter 2512.
if you entered a wrong number, press the
CLEAR button to delete it, then enter the
correct number
PR DATE START END
+02 25.12
--: ---- -:-.
n
b Set the recording start and end times
(e.g. start 21:30, end 23:15).
E’xamp/e: Enter213023 15.
{
PR DATE START END
*O2 25.12
21:30 23:15
I
T When alithe settings areas desired,
press the OK button.
You can programme another recording by
repeating steps 4 to 7.
8
Insert a video cassette with
erasure-prevention tab.
● Make sure the tape is longer than the
total recording time.
g Press the PC)VVERbutton.
The timer indicator (H) will light on the VCR
display and the VCR goes into timer
recording stand-by mode.
To record from an external source
At step
4,
Press the INPUT button.
“L1” is displayed instead of the programme
position number.
If a programme position number is already
displayed, first press the
CLEAR button.
Additional settings
After step 5,
Daily/Weekly recording
Press the (CH+) button repeatedly to select:
“M-F: for daily recording (Monday through
Friday)
“WK”: for weekly recording (the same
programme every week)
No display: for one time recording
Note:
Daily recording starting on a Saturday or Sunday
will not be possible.
ON-SCREENOPERATION
POWER---–=
MENU/TV
CH+ —
CLEAR -
!!
[
L::: 0-9
-00
Y“ 0’
—
INPUT
0
14
ON-SCREENOPERATION
B
[~
MENWTV--~:::____~_9
CH+, - -,=u:
CLEAR --
1
Programme priority
● Ifseveraltimer recordings have
overlapping recording time, the
recording wilh Ihe earlieststart
time will be recorded first, until the
end,
1900
20;00 21;00 2~oo 2~oo
L-]
-
These portionswill notberecorded
5.
ADVANCEDOPERATION
External
input mode selection
PresstheINPUTbutton.
“L1” is displayed instead of the
programme position number,
“L1”: AUDIOiVIDEOIN (Rear)
CAUTION:
Theunauthorizedrecordingof
televisionprogrammed,videotapes,
filmsandothersuchmaterialmay
infringeuponcopyrightortherights
ofthirdparties,
15
i
ON-SCREEN TIMER RECORDING PROGRAMMING
Confirmation
● To correct a programmed timer recording,
first cancel it, then reprogrammed it as
1 Press the MENU~V button.
MENU
1. T I MER PROGRAM SET
2. PROGRAM CHECK/ CLEAR
3. VCR SETUP
4. CLOCK SET
I
[0-91 +SELECT
[MENUI +TV
09.12.96 16:15
2 F’ress the numeric2 button.
● Programmed timer recordings are listed.
PR DATE START END
*O I 23.12
15:30 16:00
02 25.12 10:30 11:00
----, --
_-: ____ :-_
------- --------- :__
----. --
--: ---- :--
_______ __:---- :__
[+/-] +SELECT
[CLEARI *CANCEL
[MENUI+TV
desired,
● To cancel a programmed timer recording,
continuewithstep 3,
● To return to the normalTVbroadcast
screen, press the MENU/lVbutton,
Canceling
3
4
5
—..
Using the (CH+ or CH–) button, select the
programme to cancel.
f
PR DATE START END
01 23.12 15:30 16:00
+02 25.12
10:30 11:00
---- ----- :----- :_-
------- --: ____ :-_
------- ------- ___
---- ,---- :---- :--
[+/-] +SELECT
[CLEARI +CANCEL
[MENUI +TV
\
Press the CLEAR button,
When finished, press the MENU/TV
button,
TAPE COPY
Copying (dubbing) a tape can be done using
two video recorders, a playback VCR and a
recording VCR.
Recording VCR
,---
———-
—
I
Playback VCR (Camcorder)
I Camcorder
VCR
for RECORDING VCR
1 Insert avideo cassette with
erasure-prevention tab.
z Set to the record pause mode,
The record pause mode is set by
pressing the REC button then the
PAUSE/STILL button.
for PLAYBACK VCR (Camcorder)
s Insert the recorded videocassette.
d Start playback bypressing the PLAY
button.
for RECORDING VCR
5
6
When the desired starting position is
reached, start recording by pressing the
PAUSE/STILL button or the REC button,
When finished, press the STOP button on
the RECORDING VCR then on the
PLAYBACK VCR,
TROUBLESHOOT
NG
Symptom Check points
POWER TROUBLE
No power c The power cord is disconnected.
.-
The remote control unit
. The batteries are low.
doesn’t operate
RECEIVER TROUBLE
No TV programmed
. Are the connections between your VCR and TV correct?
received
. Was tuning correctly preset?
—.
Off
the air reception on the ● The video channel setting of the TV receiver does not
VCR is poor
correspond to the video channel presetting of the VCR!
PLAYBACK TROUBLE
Playback picture does not
● The video channel setting of the TV receiver does not
appear
correspond to the video channel presetting of the VCR.
Interference in playback
● Adjust the tracking control.
picture
● Dust or dirt on video heads, Take the VCR to an
Authorized Service Centre or dealer.
RECORDING TROUBLE
No recording
● The erasure-prevention tab on the cassette has been
removed.
.
Timer recording is not . The starting day and time have not been set correctly.
possible
● The clock time is not set correctly.
. There has been a power interruption of more than 1 hour.
6
ii
OTHER
6
OTHER
:
SPECIFICATION:)
General
Video format:
Television system:
Video heads:
Tape speed:
RF converter:
Converter output:
Timer indication:
Power failure backup:
Timer recording:
Power requirement:
Dimensions (W x H x D):
Weight:
Power consumption:
Electrical characteristics
Video input:
Video output:
Audio input:
Audio output:
Video SIN:
Horizontal resolution:
‘.lHS PAL/NTSC4.43
CCIR: 625 lines, PAL colour signals
:?heads
i“AL: 23.39 mm/see
dTSC (Playback only): 33.35
mm/see
1luilt-in UHF converter
(In channel G: 32-41, B: 33-43
:!4-hour indication
,‘\pprox. one hour
I year 6 programmed with every day (Monday through Friday)
:
lnd weekly recording function
:‘20-240 V AC, 50Hz
:160 x97x 290 mm
,
\pprOx. 5 kg
:‘OW (in operation), less than 6 W (power off)
:’I.5 - 2.OVp-p, 75 + 5 ohms
i.0 t 0.2Vp-p, 75*5 ohms
8.0 dBs, more than 50 kohms
8.0 cIBs, less than 10 kohms
!Aore than 43 dB
!Aore than 240 lines
Appearance and specification IS are subject to change without notice.
Automatic head-cleaning systc .n
This VCR is eql tipped with an: utomatic head-cleaning system which automatically cleans
the heads every time a casset’ ?is loaded or unloaded. However this system cannot
completely clean the VCR hea ISand if during playback noise appears in the picture, it is
recommended to have the he::% cleaned professionally by an Authorized Service Centre.
Repairs
This VCR is a l~recision instrun ent and if treated with care will provide satisfactory
performance, However, in the went of difficulty, the owner is advised not to attempt to make
repairs or open the cabinet. SI rvicing should always be referred to your dealer or
Authorized Service Centre.
I
I
s
*o
lAC6Pl Pi233--
PP2N/A3Cl P (0596 KP-NIO1)
SANYO Electric Co., Ltd.
Printed in Indonesia
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
Sanyo VHR-630 is a video cassette recorder featuring VHS high picture quality technology. It can be connected with a standard aerial or, for high quality of picture and sound, via AV to a TV receiver. It's equipped with G-CODE timer recording capability, featuring on-screen programming. It can play NTSC tapes and features extended playback modes, including endless play, variable speed playback and index search. It supports frame advance and has a counter with reset function, as well as a digital clock that can be set manually.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Panasonic NVSJ550AM Operating instructions
-
-
-
-
-
-
-
-
-